Example: barber
ecocirc XL ecocirc XLplus - Xylem Inc.
2. Pull down the contact retention spring 3. Connect the cable according to the wiring diagram 4. Align the two parts of the connector 5. Push the two parts one inside the other 6. Close the connector and tight carefully the cable gland For terminal-connected models, see Figure 5 and follow the subsequent steps: 1.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Statement on Efforts to Combat Modern Slavery …
www.xylem.comStatement on Efforts to Combat Modern Slavery and Human Trafficking in Supply Chains Xylem is a leading global water technology company with operations in more than 150 countries, featuring
dewatering pump - Xylem US
www.xylem.comFlygt 2400.402 dewatering pump tough pumps for dewatering The Flygt dewatering pumps from Xylem are designed for tough operating conditions. The pumps are ideal for …
Design Recommendations - Xylem US
www.xylem.com3 This brochure is intended to help application engineers, designers, planners, and users of sewage and stormwater systems who are incorporating submerged submersible
Flygt ENM-10 liquid level regulators
www.xylem.com3. The pumping process stops when the lower regulator re-turns to the vertical position and signals a stop. 1. Media to be pumped reaches the pre-set level and tilts the upper regulator, which signals the start of the pumping process. In a two-pump station, four level regulators are generally used. One is positioned at the stop level,
The Flygt N-technology pump series for water and …
www.xylem.comAdvanced technology guides the design of every component From the motor and seals to the shaft and impellers, every component in a Flygt N-pump is designed, engineered and manufactured to optimize operation and prolong service life. Advanced technology guides the design of all aspects of the pump. One example is the
THE COMPLETE GUIDE TO Stormwater Management
www.xylem.comstormwater collection system, applying best management practices (BMPs) and implementing the right pumping storage and treatment infrastructures can help these individuals protect their communities from evolving natural hazards.
Design Recommendations - Xylem Inc.
www.xylem.comfoR pump stations with miDRange centRifugal flygt wastewateR pumps. 2 This document is intended for designers, planners, and users of sewage and storm-water pumping systems that incorporate Flygt submersible pumps in the range of 3152-3301 (320 gpm-5500 gpm).
Design Recommendations - For Pump Stations ... - Xylem Inc.
www.xylem.comchamber dimensioning, valve selection, etc. should also be considered in wastewater pump station design. These matters are not addressed in this brochure, but we can offer advice on these topics. Please consult with our engineers to achieve optimum pump performance, maximum pump life, and a guarantee that product warranties are met. The design
MultiTrode - Xylem Inc.
www.xylem.comMultiTrode, Inc - USA 990 South Rogers Circle, Suite 3 Boca Raton, Florida 33487 Tel: 561.994.8090 Fax: 561.994.6282 USsales@multitrode.com MultiTrode - UK
Best practices in pump system design
www.xylem.comNet positive suction head required (NPSHr) is a pump characteristic that is not related to the system. All pump NPSHr’s are different and the values can be obtained from the pump manufacturer. Hole in pump impeller vane. Impeller damage. 4 By definition, because there is a large cross section at position
Related documents
dsPIC33/PIC24 FRM, High-Speed PWM Module
ww1.microchip.com• Complementary mode • Push-Pull mode • True Independent mode • FCLCONx: PWMx Fault Current-Limit Control Register - Selects the current-limit control signal source - Selects the current-limit polarity - Enables or disables the Current-Limit mode - Selects the Fault control signal source - Configures the Fault polarity
AN1279 - Offline UPS Reference Design Using the dsPIC DSC
ww1.microchip.comAug 02, 2011 · and the primary current meas urement (IP) protects the converter in case of transformer flux walking. The PWM outputs from the dsPIC DSC are firing pulses to the driver to control the output voltage. Table 2 lists the resources used by the dsPIC DSC device for a push-pull converter. FIGURE 5: PUSH-PULL CONVERTER RESOURCE DIAGRAM
Nexys A7 FPGA Board Reference Manual - Digilent Reference
digilent.comThe audio output (AUD_PWM) needs to be driven open-drain as opposed to push-pull on the Nexys 4. 1 Functional Description 1.1 Power Supplies The Nexys A7 board can receive power from the Digilent USB-JTAG port (J6) or from an external power supply. Jumper JP3 (near the power jack) determines which source is used.