Example: stock market

EN 1993-1-8: Eurocode 3: Design of steel structures …

The European UnionIn order to promote public education and public safety, equal justice for all, a better informed citizenry, the rule of law, world trade and world peace, this legal document is hereby made available on a noncommercial basis, as it is the right of all humans to know and speak the laws that govern them. EDICT OF GOVERNMENT EN 1993-1-8 (2005) (English): Eurocode 3: Design of steelstructures - Part 1-8: Design of joints [Authority: TheEuropean Union Per Regulation 305/2011, Directive 98/34/EC,Directive 2004/18/EC]EUROPEAN STANDARD EN 1993-1-8 NORME EUROPEENNE EUROpAISCHE NORM ICS May 2005 English version Supersedes ENV 1993-1-1 :1992 Incorporating Corrigenda December 2005 and July 2009 Eurocode 3: Design of steel structures -Part 1-8: Design of joints Euroeode 3.

BS EN 1993-1-8:2005 EN 1993-1-8:2005 (E) Foreword This European Standard EN 1993, Eurocode 3: Design of steel structures, has been prepared by Technical

Tags:

  Design, Structure, Steel, Design of steel structures

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of EN 1993-1-8: Eurocode 3: Design of steel structures …

1 The European UnionIn order to promote public education and public safety, equal justice for all, a better informed citizenry, the rule of law, world trade and world peace, this legal document is hereby made available on a noncommercial basis, as it is the right of all humans to know and speak the laws that govern them. EDICT OF GOVERNMENT EN 1993-1-8 (2005) (English): Eurocode 3: Design of steelstructures - Part 1-8: Design of joints [Authority: TheEuropean Union Per Regulation 305/2011, Directive 98/34/EC,Directive 2004/18/EC]EUROPEAN STANDARD EN 1993-1-8 NORME EUROPEENNE EUROpAISCHE NORM ICS May 2005 English version Supersedes ENV 1993-1-1 :1992 Incorporating Corrigenda December 2005 and July 2009 Eurocode 3: Design of steel structures -Part 1-8: Design of joints Euroeode 3: Caleul des structures en aeier - Partie 1-8.

2 Calcul des assemblages Eurocode 3: Bemessung und Konstruktion von Stahlbauten - Teil 1-8: Bemessung von Anschlussen This European Standard was approved by CEN on 16 April 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-tO-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

3 This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

4 EUROPEAN COMMITTEE FOR STANDARDIZATION COMlTE EUROPEEN DE NORMALISATION EUROpA I HES KOMlTEE FUR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEI\J national Members. Ref. No. EN 1993-1-8: 2005: E BS EN 1993-1-8: 2005 EN 1993-1-8: 2005 (E) Contents Page Introduction .. 8 1.] Scope .. 8 N01111ative references .. 8 Distinction between Principles and Application Rules .. 1 0 ] .4 Tenns and definitions .. 1 0 SY111bols.

5 13 2 Basis of Design .. 18 AsslIlnptions .. 18 General requirenlents .. 18 Applied forces and 1l101l1ents .. J 8 Resistance of joints .. 18 Design assunlptions .. 19 Joints loaded in shear subject to impact, vibration and/or load reversal .. 19 Eccentricity at intersections .. 19 3 Connections made \vith bolts, rivets or pins .. 20 3.] Bolts, nuts and "vashers .. 20 General .. 20 PreJoaded bolts .. 20 Rivets .. 20 Anchor bo1ts .. 2] Categories ofboJted connections .. 21 1 Shear connections .. 2] Tension connections.

6 21 Positioning of holes for bolts and rivets .. 23 Design resistance of individual fasteners .. 24 Bolts and rivets .. 24 Injection bolts .. 28 Group of fasteners .. 29 .Longjoints .. 29 Slip-resistant connections using or bolts .. 30 J Design Slip resistance .. 30 Combined tension and shear .. 31 Hybrid cOl1nections .. 31 Deductions for fastener holes .. 31 General .. 31 Design for block tearing .. 32 Angles connected by one and other unsymmetrically connected members in tension .. 33 Lug.

7 34 J Prying forces .. 34 of forces between fasteners at the ultimate limit state .. 34 Connections made with 3. J General .. 35 Design of pins .. 35 4 \Velded connections .. 38 General .. 38 Welding consu1l1ables .. 38 Geollle1ry and dilnensions .. 38 ] Typeof\veld .. 38 Fillet welds .. 38 fillet \ve1ds all rOLlnd .. 40 Butt \-velds .. 40 Plug vvelds .. 41 2 BS EN 1993-1-8: 2005 EN 1993-1-8: 2005 (E) Flare groove welds .. 41 Welds with pa(~Kllt1g~ .. Design resistance of a fillet \veld .. 42 Length of welds.)

8 42 Effective throat thickness ..42 Resistance of fillet welds ..42 resistance of fillet welds all round .. 44 Design resistance of butt welds ..45 Full penetration butt welds ..45 Partial penetration buH welds ..45 T-butt joints .. 45 Design resistance of plug welds ..45 Distribution of forces .. 46 Connections to unstiffened tlanges ..46 ] Long joints .. 48 Eccentrically loaded single fillet or single-sided partial penetration butt welds ..48 connected by one leg .. 48 Welding in cold-formed zones.

9 49 5 Analysis, classification and modelling .. 50 Global analysis .. 50 General .. 50 Elastic global .. 50 Rigid-plastic global analysis .. 51 Elastic-plastic global analysis .. 51 Global analysis of lat6ce girders .. 52 Classification of joints .. 54 General .. 54 Classification by stiffness .. 54 Classification by strength .. 55 Modelling of beam-to-column joints .. 56 6 Structural joints connecting H or 1 sections .. 60 General .. 60 Basis .. 60 Structural properties .. 60 Basic components of a joinL.

10 6] Design Resistance .. 65 Internal forces .. 65 Shear forces .. 65 Bending lnOlnents .. 66 Equivalent T-stub in tension .. 67 Equivalent T -stub in compression .. 70 Resistance of basic components .. 71 moment resistance of beam-to-column joints and splices .. 84 resistance of column bases with base plates .. 89 Rotational stiffness .. 92 Basic tllodel .. 92 Stiffness coefficients for basic joint components .. 94 End-plate joints with two or more bolt-rows in tension .. 97 Colulnn bases .. 98 Rotation capacity.


Related search queries