EN 300 220-1 - V2.1.1 - Electromagnetic …

1 ETSI EN 300 220-1 (2006-04)European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Short Range Devices (SRD);Radio equipment to be used in the 25 MHz to 1 000 MHzfrequency range with power levels ranging up to 500 mW;Part 1: Technical characteristics and test methods ETSI ETSI EN 300 220-1 (2006-04) 2 Reference REN/ERM-TG28-0403-1 Keywords radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistr e la Sous-Pr fecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).

2 In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2006. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.

3 3 GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3 GPP Organizational Partners. ETSI ETSI EN 300 220-1 (2006-04) 3 Contents Intellectual Property Rights ..8 1 Scope ..10 2 References ..10 3 Definitions, symbols and abbreviations ..11 Definitions ..11 Symbols ..12 Abbreviations ..12 4 Technical requirement specifications ..13 General requirements ..13 Receiver classification ..13 General performance criteria for receiver ..13 Presentation of equipment for testing Choice of model for testing ..13 Auxiliary test equipment ..14 Declarations by the provider ..14 Definitions and declarations of Switching Range (SR), alignment range and operational frequency range ..14 Definition and declaration of Definition and declaration of alignment range.

4 14 Definition of operating frequency range ..14 Definition of the categories of the alignment range (AR0, AR1, AR2 and AR3) ..14 Testing of equipment of category Testing of equipment of category Testing of equipment of category Testing of equipment of category Testing of equipment capable of being aligned to operate with more than one frequency Number of samples for testing ..15 Testing of a family of equipment with a total operating range in excess of each equipment's alignment range ..16 Testing of frequency agile or hopping equipment ..16 Testing of equipment with alternative power levels or frequency Declaration and testing of equipment that does not have an external 50 ohm RF connector (integral antenna equipment)..17 Equipment with an internal permanent or temporary antenna connector ..17 Equipment with a temporary antenna connector ..17 Mechanical and electrical Controls.

5 18 Transmitter shut-off facility ..18 Marking ..18 Equipment identification ..18 Receiver mute or 5 Test conditions, power sources and ambient temperatures ..18 Normal and extreme test conditions ..18 Test power External test power source ..19 Internal test power source ..19 Normal test Normal temperature and humidity ..19 Normal test power source ..19 Mains voltage ..19 Regulated lead-acid battery power sources ..19 ETSI ETSI EN 300 220-1 (2006-04) 4 Other power Extreme test conditions ..20 Extreme temperatures ..20 Extreme temperature Procedure for tests at extreme Procedure for equipment designed for continuous operation ..20 Procedure for equipment designed for intermittent operation ..20 Extreme test power source.

6 21 Mains voltage ..21 Regulated lead-acid or gel-cell type batteries ..21 Power sources using other types of Other power 6 General Normal test signals and test Normal test signals for analogue speech ..22 Normal test signals for data ..22 Artificial antenna ..22 Test fixture ..22 Test sites and general arrangements for radiated measurements ..23 Modes of operation of the transmitter ..23 Measuring receiver ..23 7 Measurement uncertainty ..24 Interpretation of results ..24 Measurement uncertainty is equal to or less than maximum acceptable Measurement uncertainty is greater than maximum acceptable 8 Methods of measurement and limits for transmitter parameters ..25 Frequency error or frequency drift ..25 Definition per equipment category.

7 26 Definition for narrowband systems ..26 Definition for wideband Narrowband ..26 Method of Wideband ..26 Method of Carrier power (conducted)..27 Definition ..27 Method of measurement ..27 Effective radiated power ..28 Definition ..28 Methods of measurement ..28 Spread spectrum modulation ..29 Frequency hopping spread spectrum devices (FHSS) ..30 FHSS definitions ..30 FHSS declarations ..30 Limits ..30 Direct sequence or spread spectrum other than FHSS ..31 Definition.

8 31 Limits ..31 Transient power ..31 Definition ..31 Method of measurement ..31 Characteristics of the transient power measuring device ..32 Adjacent channel power ..33 Definition ..33 Method of measurement ..33 ETSI ETSI EN 300 220-1 (2006-04) 5 Modulation bandwidth for wideband Definition ..34 Method of measurement ..34 Spurious emissions ..34 Definition ..35 Method of measuring the power level in a specified load, clause a) i) ..35 Method of measuring the effective radiated power, clause a) ii) ..35 Method of measuring the effective radiated power, clause b) ..36 Frequency stability under low voltage conditions.

9 37 Definition ..37 Method of measurement ..37 Duty Definitions ..37 Duty cycle class limits ..38 Principle for Listen Before Talk (LBT)..38 LBT timing parameters ..39 Minimum transmitter off-time ..39 Limit ..39 LBT minimum listening time ..39 Limit for minimum listening time ..39 Acknowledge transmissions ..40 Maximum transmitter on-time ..40 Limit ..40 Declaration of LBT Equipment with or without LBT using transmitter time-out-timer ..40 9 Receiver parameters ..40 Maximum usable sensitivity (conducted)..41 Definition ..41 Method of measurement with continuous bit Method of measurement with messages.

10 42 Receiver LBT threshold and transmitter max on-time ..43 Definitions ..43 Method of measurements ..43 Adjacent channel Definition ..44 Method of measurement ..44 Limit for adjacent channel selectivity ..45 Limit for receiver saturation at adjacent channel ..46 Blocking or desensitization ..46 Definition ..46 Method of measurement ..46 Limit for blocking ..47 Limit for blocking for receivers with Limit for receiver Intermodulation response rejection ..47 Definition ..47 Method of measurement ..48 Limit for intermodulation rejection ..48 Spurious response rejection.