ENGINE Workshop Manual 4G9 (E-W)

1 11 AMITSUBISHIENGINE4G9 SERIES (E - W) Workshop No. PWEE9502-FFOREWORDThis Workshop Manual contains procedures forremoval, disassembly, inspection, adjustment,reassembly and installation, etc. for information, illustrations and productdescriptions contained in this Manual are currentas at the time of publication. We, however, reservethe right to make changes at any time withoutprior notice or INSTRUCTIONP lease keep these Manual pages in the binderNo. these pages according to the signs Added , Revised and Deleted on the Listof effective pages which are :File the pages with this sign additionally inyour , Deleted.

2 Replace the existing pages with thecorresponding pages with this sheets will be suppliedupon Motors Corporation July 1999 INTRODUCTIONM aintenance and Servicing Procedures(1) A diagram of the component parts isprovided near the front of each section inorder to give the reader a better under-standing of the installed condition ofcomponent parts.(2) The numbers provided within the diagramindicate the sequence for maintenance andservicing procedures.: Indicates a non-reusable tightening torque is provided steps:The part designation number correspondsto the number in the illustration to indicateremoval steps:The part designation number correspondsto the number in the illustration to indicatedisassembly steps:Specified in case installation is impossiblein reverse order of removal steps.

3 Omittedif installation is possible in reverse orderof removal steps:Specified in case reassembly is impossiblein reverse order of disassembly if reassembly is possible in reverseorder of disassembly of Major Maintenance/Service PointsWhen there are major points relative to maintenance and servicing procedures(suchasessentialmaintenanceand servicepoints, maintenanceand servicestan-dard values, information regarding the use of special tools, etc.), these are ar-ranged together as major maintenance and service points and explained in ": Indicates that there are essential points for removal or disassembly.

4 "AA: Indicates that there are essential points for installation or for Lubrication, Sealants and AdhesivesInformation concerning the locations for lu-brication and for application of sealants andadhesives is provided, by using symbols, inthe diagram of component parts, or on thepage following the component parts page,and explained.: Grease (multipurpose grease unlessthere is a brand or type specified): Sealant or adhesive: Brake fluid, automatic transmission fluidor air conditioner compressor oil: ENGINE oil or gear oilEXPLANATION OF Manual CONTENTSI ndicates thegroup thesection thegroup thepage non-reusable number corresponds tothe number appearing in Removal steps , Disassembly steps , Installation steps or Reassembly steps.

5 Issue datePublication number-Revision code4G9 ENGINE (E - W) - Water Pump and Water Hose11A-7-17. WATER PUMP AND WATER HOSEREMOVAL AND INSTALLATION <SOHC>Removal hose hose coolant temperature gauge outlet inlet inlet pumpINSTALLATION SERVICE POINTSWATER PUMP INSTALLATION(1)Apply a 3 mm diameter of Form-In-Place Gasket (FIPG)to the location shown in the sealant:Mitsubishi Genuine Part No. MD970389 orequivalent."GA"DA"BA"BA"AA"CAEM itsubishi Motors CorporationMay 1995 PWEE9502"AA"BA29 Nm10 Nm24 Nm14 Nm14 Nm14 Nm14 Nm12111092431876524 NmIndicates thesection procedures, cau-tions, etc.

6 On removal, installa-tion, disassembly and reas-sembly are described."FA" and 11A-0-4 CJuly199711A-1-1 to and to and and to and to and to Revised11A-5-3 to to to and 11A-6a-2 DJun. 199811A-6a-3 and to to to to to 11A-8a-5 ANov. 199511A-8b-1 and 11A-8b-2 ANov. 199511A-9-1 and and 11A-9-3bCJuly 199711A-9-4 to 199511A-10-1 May 199511A-10-2 DJun. 199811A-10-3 to to 11A-11-8 May199511A-12-1 CJuly 199711A-12-1a and to 11A-12-6 ANov. OF EFFECTIVE PAGESPageRevisionCodeDateRemarksPageRevi sionCodeDateRemarksMissing sheets willbe supplied 1999 Mitsubishi Motors CorporationRevis