English - Power Washers from Power Washer.US

1 2 EnglishDate of Purchase: / /200 Your Model Number is: HD1500 IMPORTANTA ttention Valued Customer: The serial number of your machine and date of purchase is necessary information to facilitate warranty claims and the ordering of replacement ease of reference, please record this information in the space provided Number: ..Additionally, you can conveniently register your new HD1500 HSDS at the mounting template is designed to ac-commodate stud layout of 16 inch ( cm) on : Stud layouts may your wall studs are not located 16 apart, use a 1/2 ( mm) thick, 8 ( cm) wide, plywood panel long enough to attach to the studs using (4) # 12x2 wood screws (not provided).The mounting brackets may then be attached to the plywood panel using the 4 screws (28) plywood installation, to prevent the unit from falling, make sure you select the proper length of fastener for the secure mounting of plywood to the wall is necessary to affix the mounting plate directly to a framing stud or other ap-propriate surface able to support 67 lbs (30 kg).

2 Fig. 1 Fig. 2 WARNINGWARNINGWARNINGM ounting bracket is designed for use with HD 1500 HSDS local hardware professional for proper mounting to use proper mounting fasteners or follow mounting instructions may result in damage to equipment, property or personal MOVING AND STORAGE ASSEMBLY INSTRUCTIONS(Refer to pages 3, 4, 6, and 7).Mount wall bracket (15) using template (14). See fig. 1 and 2 on page the wall bracket (15) level at a height not lower than 1 m ( ft) from the floor ( ).Assemble the support arm (16) to the base (17) by using screws supplied (18) as shown in Fig. the hose reel (20) under the mounting flange (19) and assemble retaining brackets (21) using four screws provided (22) as shown in Fig. handle (23) to lever on hose reel with the remaining screw (24) as shown in Fig.

3 The assembled home storage docking station to the wall bracket (15) as shown in Fig. high pressure cleaner on the docking station See LIST (Fig. 8)1 spray Gun2 Variable nozzle with Lance3 GFCI4 Water Inlet Filter Screen5 Quick Connect Assembly6 High-Pressure Hose 7 Safety Lock8 Motor and Pump in Case9 Power Supply Cord10 ON/OFF Switch11 Soap Lance Assembly12 High Pressure Outlet13 Shipping Plug14 Mounting template (provided)15 Wall bracket16 Support arm17 Base18 Screw19 Hose reel mounting flange20 Hose reel21 Retaining brackets22 Screw23 Handle24 Screw25 Soap dispenser storage location26 Lance storage location27 spray gun storage location28 # 12x1 6/8 Phillips Flat Head Wood screws (US equivalent # 12x1 1/2 Phillips Flat Head Wood screws) 8 English MOVING AND STORAGE INSTRUCTIONS.

4 Page 3 ASSEMBLY INSTRUCTIONS .. page 5 SAFETY INSTRUCTIONS .. page 12 OPERATING CONNECTIONS .. page 12 HIGH PRESSURE HOSE .. page 12 WATER CONNECTION .. page 12 Power SUPPLY CONNECTION .. page 12 OPERATING INSTRUCTIONS .. page 13 START-UP PROCEDURE .. page 13 VARIO spray nozzle .. page 13 USE OF CLEANING CHEMICALS .. page 16 CLEANING TECHNIQUES .. page 16 END OF OPERATION .. page 16 HOSE REEL KIT .. page 16 MAINTENANCE .. page 17 SERVICING A DOUBLE-INSULATED APPLIANCE .. page 17 TROUBLESHOOTING .. page 18 TECHNICAL DATA .. page 19 INDEX12 EnglishThe pressure washer is equipped with a stop device which will sense when the trigger on the gun is released. It will open the Power circuit to the motor and cause the pressure washer to : The pressure washer is also equipped with a main Power on/off switch located on the unit.

5 It should always be moved to the off position when the pressure washer is not being used to prevent possible injury or OVERLOADThe electric motor in this pressure washer is equipped with an overload protection device which will automa-tically shut off the motor in the event the motor draws excessive current or device will automatically reset itself and resume normal operation after a short period of time. IMPORTANT SAFETY INSTRUCTIONS GROUND-FAULT CIRCUIT-INTERRUPTER PRO-TECTIONThis pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the Power supply cord. This device provides additional protection from the risk of electric shock. If replacement of the plug or cord is needed, use only identical replacement Power SUPPLY CONNECTIONThe pressure washer is factory-equipped with an electrical cord and a ground fault circuit interrupter (GFCI) plug ( ).

6 This cord should only be connected to an electrical outlet installed in accordance with local safety : The Power supply must be 120V, 60hz and a minimum 15 amp dedicated : Test GFCI before each use. DO NOT use pressure washer if test below :Proper water connection ( ). HIGH PRESSURE HOSER emove and discard the water plug. ( )Attach the high pressure hose by carefully inserting the fitting with the o-ring into the high pressure outlet and tighten the threaded nut by hand. ( ) WATER CONNECTION (Cold water)Before connecting, run water through the garden hose (not supplied) to flush out any foreign matter. Attach garden hose to the pressure washer water inlet con-nection. (Fig. 11)If your water source is a well, the garden hose length can only be 30 ft. (9m) max. OPERATING CONNECTIONS (See pages 9-11)WARNINGWARNING: When using this product basic precautions should always be fol-lowed, including the following:1 Read all the instructions before using the To reduce the risk of injury, do not operate near Be thoroughly familiar with the Stay alert - watch what you are Do not operate the product when fatigued or under the influence of alcohol or Keep operating area clear of all Do not overreach or operate unit on unstable surface.

7 Keep good footing and balance at all Follow the maintenance instructions specified in the : Risk of injury - Do not direct discharge stream at THESE INSTRUCTIONSGFCI Test Procedures ( ): 1. Plug GFCI into Power receptacle. Indicator should turn Press test button. Red indicator should Press reset button for use. Do not use if above test failsNOTE: The GFCI must be reset each time the pressure washer is connected to an electrical outlet. Reset by simply pushing the reset button on the GFCI Power Connect only to properly grounded outlet. B. Inspect cord before using. Do not use if cord is damagedC. Keep all connections dry and off the Do not touch plug with wet The pressure washer is provided with a ground-fault circuit interrupter built into the Power plug. If replacement of the plug or cord is needed, use only identical replacement parts.

8 Contact Customer Service for proper replacement using an extension cord, observe the specifi-cation below:Cable Length Wire Gauge Up to 25 ft. 12 AWG OutdoorWARNING: To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet Inspect cord before using. Do not use if cord is damagedB. Keep all connections dry and off the Do not touch plug with wet CIRCUIT-INTERRUPTER PRO-TECTIONA. Connect to only a properly grounded GFCI circuit. B. This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the Power -supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary , use only identical replacement parts that include GFCI protection.

9 OPERATING INSTRUCTIONSWARNING: Risk of Injury. Do not direct discharge stream at Press Power switch on the pressure washer to the ON position. ( ) As shown on page Squeeze the gun trigger to start the pressure : Make sure the wand is pointed in a safe direction when starting the pressure washer. Do not point at face or feet as serious injury could START-UP PROCEDURE1. Make sure water supply is connected and turned Make sure the unit is plugged Release gun safety if locked. (Fig. 17) Shown on page Remove any dirt or foreign matter from the gun outlet and the male connector of the Insert the wand into the gun s quick connect cou-pling by pushing firmly and twisting wand of a turn to lock into place. (Fig. 13) Shown on page To allow air to escape from the hose, squeeze trigger on the gun until there is a steady stream of water coming from the : Make sure wand is locked.

10 (see ) As shown on page : Make sure wand is : If the wand is not securely locked into place, it could be ejected under high pressure when operating the VARIABLE spray NOZZLEThe variable spray nozzle can adjust spray from fan to pencil point. The spray is adjusted by turning the nozzle . ( ) See page CORDSUse only extension cords that are intended for outdoor use. These extension cords are identified by a marking Acceptable for use with outdoor appliances: store indoors while not in use . Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not pull on any cord to disconnect.