Environmental Conditions for Human Occupancy

1 ANSI/ASHRAE Standard 55-2004(Supersedes ANSI/ASHRAE Standard 55-1992)ThermalEnvironmentalConditions forHuman OccupancyApproved by the ASHRAE Standards Committee on Janu-ary 24, 2004; by the ASHRAE Board of Directors on Janu-ary 29, 2004; and by the American National StandardsInstitute on April 16, Standards are scheduled to be updated on afive-year cycle; the date following the standard number isthe year of ASHRAE Board of Directors approval. Thelatest copies may be purchased from ASHRAE CustomerService, 1791 Tullie Circle, NE, Atlanta, GA : Fax: 404-321-5478. Tele-phone: 404-636-8400 (worldwide) or toll free 1-800-527-4723 (for orders in and Canada). Copyright 2004 American Society of Heating,Refrigerating and Air-Conditioning Engineers, 1041-2336 When addenda or interpretations to this standard havebeen approved, they can be downloaded free of chargefrom the ASHRAE web site NOTEThis American National Standard (ANS) is a national voluntary consensus standard developed under the auspices of the AmericanSociety of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).

2 Consensus is defined by the American National StandardsInstitute (ANSI), of which ASHRAE is a member and which has approved this standard as an ANS, as substantial agreement reachedby directly and materially affected interest categories. This signifies the concurrence of more than a simple majority, but not necessarilyunanimity. Consensus requires that all views and objections be considered, and that an effort be made toward their resolution. Compliance with this standard is voluntary until and unless a legal jurisdiction makes compliance mandatory through obtains consensus through participation of its national and international members, associated societies, and Standards are prepared by a Project Committee appointed specifically for the purpose of writing the Standard.

3 TheProject Committee Chair and Vice-Chair must be members of ASHRAE; while other committee members may or may not be ASHRAE members, all must be technically qualified in the subject area of the Standard. Every effort is made to balance the concerned interestson all Project Committees. The Manager of Standards of ASHRAE should be contacted for:a. interpretation of the contents of this Standard,b. participation in the next review of the Standard,c. offering constructive criticism for improving the Standard,d. permission to reprint portions of the INDUSTRIAL ADVERTISING POLICY ON STANDARDSASHRAE Standards and Guidelines are established to assist industry and the public by offering a uniform method of testing for rating purposes, by suggesting safe practices in designing and installing equipment, by providing proper definitions of this equipment, and by providing other information that may serve to guide the industry.

4 The creation of ASHRAE Standards and Guidelines is determined by the need for them, and conformance to them is completely referring to this Standard or Guideline and in marking of equipment and in advertising, no claim shall be made, eitherstated or implied, that the product has been approved by uses its best efforts to promulgate Standards and Guidelines for the benefit of the public in light of availableinformation and accepted industry practices. However, ASHRAE does not guarantee, certify, or assure the safety orperformance of any products, components, or systems tested, installed, or operated in accordance with ASHRAE s Standardsor Guidelines or that any tests conducted under its Standards or Guidelines will be nonhazardous or free from STANDARDS COMMITTEE 2003-2004 Van D.

5 Baxter, ChairDavor Novosel, Vice-ChairDonald B. BivensDean S. BorgesPaul W. CabotCharles W. Coward, F. CrowtherBrian P. DoughertyHakim ElmahdyMatt R. HarganRichard D. HermansJohn F. HoganFrank E. JakobStephen D. KennedyDavid E. KnebelFrederick H. KohlossMerle F. McBrideMark P. ModeraCyrus H. NasseriGideon ShavitDavid R. TreeThomas H. WilliamsJames E. WoodsRoss D. Montgomery, BOD ExOKent W. Peterson, COClaire B. Ramspeck, Manager of StandardsASHRAE Standard Project Committee 55 Cognizant TC: TC , Physiology and Human EnvironmentSPLS Liaison: Frank E. JakobWayne A. Dunn, Chair*Byron W. JonesDipak J. ShahGail S. Brager, Vice-Chair*Joseph N. KnappPeter Simmonds*Gaetano AlfanoAlison G. Kwok*Jerry M. Sipes*Larry G. BerglundHal Levin*Elia M. Sterling*Karl A. BrownArsen K.

6 MelikovBenjamin P. Sun*Daniel R. ClarkBjarne W. Olesen* (Chair, 1995-1998)Steven T. Taylor*Joseph J. Deringer*Nigel A. OselandShin-Ichi TanabeClifford C. FederspielNicholas B. Rajkovich*Robert W. Tinsley*Jaap J. HogelingGary RawJorn Toftum*Daniel Int-Hout, III* (Chair, 1999-2001)David G. Scheatzle*Stephen C. Turner*James E. Woods*Denotes members of voting status when the document was approved for publicationCONTENTSANSI/ASHRAE Standard 55-2004 Thermal Environmental Conditions for Human OccupancySECTIONPAGEF oreword .. 21 Purpose .. 22 Scope .. 23 Definitions .. 24 General Requirements .. 35 Conditions that Provide Thermal comfort .. 46 117 Evaluation of the Thermal Environment .. 128 References .. 14 Normative Appendix A: Activity 15 Normative Appendix B: Clothing 16 Informative Appendix C: Acceptable Approximation for Operative Temperature.

7 20 Normative Appendix D: Computer Program for Calculation of PMV-PPD .. 21 Informative Appendix E: Thermal Environment 23 Informative Appendix F: Bibliography .. 25 Copyright 2004 American Society of Heating,Refrigerating and Air-Conditioning Engineers, Tullie Circle NEAtlanta, GA rights STANDARD 55-2004(This foreword is not part of this standard. It is merelyinformative and does not contain requirements necessaryfor conformance to the standard. It has not been pro-cessed according to the ANSI requirements for a stan-dard and may contain material that has not been subjectto public review or a consensus process.)FOREWORDS tandard 55-2004, Thermal Environmental Conditionsfor Human Occupancy , is a revision of Standard standard specifies Conditions in which a specified fractionof the occupants will find the environment thermally accept-able.

8 The revision is a consensus standard that has undergonepublic and ASHRAE review; it incorporates the relevantresearch and experience gained since the 1992 revision. Suchchanges include the addition of the PMV/PPD calculationmethods and the concept of adaptation. The standard isintended for use in design, commissioning, and testing ofbuildings and other occupied spaces and their HVAC systemsand for the evaluation of thermal environments. Because it isnot possible to prescribe the metabolic rate of occupants, andbecause of variations in occupant clothing levels, operatingsetpoints for buildings cannot be practically mandated by thisstandard. The designer may choose, in agreement with the owner orowner s representative ( , owner s agent, developer, orequivalent), the level of thermal comfort and appropriateexceedance.

9 The selected design criteria will influence theHVAC system design and may also influence the buildingdesign. This standard may also be used for evaluation of exist-ing thermal environments in buildings, during experimentalconditions, and for the development and testing of products. This standard is in close agreement with ISO Standards77261 and PURPOSE The purpose of this standard is to specify the combina-tions of indoor thermal Environmental factors and personalfactors that will produce thermal Environmental conditionsacceptable to a majority of the occupants within the space. 2. SCOPE Environmental factors addressed in this standard aretemperature, thermal radiation, humidity, and air speed; thepersonal factors are those of activity and is intended that all of the criteria in this standard beapplied together since comfort in the indoor environment iscomplex and responds to the interaction of all of the factorsthat are standard specifies thermal Environmental condi-tions acceptable for healthy adults at atmospheric pressureequivalent to altitudes up to 3000 m (10,000 ft) in indoorspaces designed for Human Occupancy for periods not lessthan 15 minutes.

10 Standard does not address such nonthermal envi-ronmental factors as air quality, acoustics, and illumination orother physical, chemical, or biological space contaminantsthat may affect comfort or DEFINITIONS adaptive model: a model that relates indoor design tempera-tures or acceptable temperature ranges to outdoor meteorolog-ical or climatalogical parameters. air speed: the rate of air movement at a point, without regardto direction. clo: a unit used to express the thermal insulation provided bygarments and clothing ensembles, where 1 clo = m2 C/W ( ft2 h F/Btu). comfort , thermal: that condition of mind which expressessatisfaction with the thermal environment and is assessed bysubjective : the unwanted local cooling of the body caused by rate (DR): percentage of people predicted to be dissat-isfied due to , thermal: the characteristics of the environmentthat affect a person's heat , acceptable thermal: an environment that asubstantial majority of the occupants would find : a single piece of ratio: the ratio of the mass of water vapor to the massof dry air in a given , relative (RH): the ratio of the partial pressure (ordensity) of the water vapor in the air to the saturation pressure(or density) of water vapor at the same temperature and thesame total , clothing/ensemble (Icl).