EUROPEAN STANDARD EN 10021 - sanyosteel.com

1 EUROPEAN STANDARD NORME EUROP ENNE EUROP ISCHE NORMEN 10021 September 1993 UDC : Iron and steel products, steels, delivery, inspection, tests, specificationsEnglish versionGeneral technical delivery requirements for steel and iron productsAciers et produits sid rurgiques Conditions g n rales techniques de livraisonAllgemeine technische Lieferbedingungen f r Stahl und StahlerzeugnisseThis EUROPEAN STANDARD was approved by CEN on 1993-09-24. CEN membersare bound to comply with the CEN/CENELEC Internal Regulations whichstipulate the conditions for giving this EUROPEAN STANDARD the status of anational STANDARD without any lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCEN EUROPEAN STANDARD exists in three official versions (English, French,German).

2 A version in any other language made by translation under theresponsibility of a CEN member into its own language and notified to theCentral Secretariat has the same status as the official members are the national standards bodies of Austria, Belgium,Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland andUnited EUROPEAN Committee for Standardization Comit Europ en de Normalisation Europ isches Komitee f r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1993 Copyright reserved to CEN membersRef. No. EN 10021 :1993 EEN10021:1993 BSI 01-19992 ForewordThis EUROPEAN STANDARD has been prepared by Technical Committee ECISS/TC 9, Technical delivery conditions and quality control of iron and steel products, the secretariat of which is held by EN 10204, EN 10021 replacesEuronorm EUROPEAN STANDARD shall be given the status of a national STANDARD , either by publication of an identical text or by endorsement, at the latest by March1994, and conflicting national standards shall be withdrawn at the latest by accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this EUROPEAN STANDARD .

3 Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United references33 Definitions34 Information to be supplied by the purchaser45 Manufacturing process56 Supply by a processor or an intermediary57 Requirements58 Inspection and testing69 Sorting and reprocessing810 Marking811 Disputes9 Annex A (informative) Bibliography13 Annex B (informative) Important standards for testing and analysis of iron and steel13 Figure 1 Terms defined in clause 39 Figure 2 Flow chart for tests and retests where the interpretation of results of non-sequential tests is based on individual values only ( for tensile test) for cases where the test unit consists of a single piece10 Figure 3 Flow chart for tests and retests where the interpretation of results of non-sequential tests is based on individual values only ( for tensile tests) for cases where the test unit consists of several piece11 Figure 4 Flow chart of sequential tests in conjunction with retests12EN10021.

4 1993 BSI 01-199931 ScopeThis EUROPEAN STANDARD specifies the general technical delivery requirements for all steel products covered by EN10079 with the exception of steel castings and powder metallurgical products (seeannexA).EN 10 204 describes the inspection documents to be the delivery requirements agreed for the order or specified in the appropriate product or material STANDARD differ from the general technical delivery requirements defined in this STANDARD , then it is the requirements agreed for the order or specified in the appropriate product or material STANDARD which shall Normative referencesThis EUROPEAN STANDARD incorporates by dated or undated reference, provisions from other publications.

5 These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this EUROPEAN STANDARD only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to 10020, Definitions and classification of grades of 10052, Vocabulary of heat treatment terms for ferrous 10079, Definitions of steel 10204, Metallic products Types of inspection 29001, Quality systems Model for quality assurance in design/development, production, installation and 29002, Quality systems Model for quality assurance in production and 29003, Quality systems Model for quality assurance in final inspection and 181), Selection and preparation of samples and test pieces for steel and iron and steel 31-0.

6 1981, General principles concerning quantities, units and TR 9769, steel and iron Review of available methods of DefinitionsIn addition to the definitions in EN 10020, EN10052 and EN10079, for the purposes of this STANDARD the following definitions inspectionactivities such as measuring, examining, testing, gauging one or more characteristics of a product or service and comparing these with specified requirements to determine testingany operation or action to determine one or more properties or characteristics of a material or continuous inspectionregular inspection and testing of the characteristics and/or manufacturing parameters of a product manufactured over a long period normally in large quantities and always to the same specification.

7 The tests and inspection are carried out according to a procedure agreed between the manufacturer and purchaser. This agreement may cover for example specifications on: the characteristics or manufacturing parameters to be tested or inspected; the condition of the products at the time of testing and inspection; the assessment of the test results (frequently statistical assessments); the right of the purchaser to verify the proper carrying out of the tests and non-specific inspection and testinginspection and testing carried out by the manufacturer in accordance with his own procedures, to assess whether products made by the same manufacturing process meet the requirements of the order.

8 The products inspected and tested may not necessarily be the products actually specific inspection and testinginspection and testing carried out, before delivery, according to the technical requirements of the order, on the products to be supplied or on test units of which the product supplied is part, in order to verify whether these products comply with the requirements of the order1) Until their transformation as EUROPEAN standards , the indicated EURONORM, or their national corresponding STANDARD , may be :19934 BSI inspection representative(s)one or more individual(s) who is/are either:a) the inspector(s) designated in the official regulations;b) the manufacturer s authorized representative(s), who is hierarchically independent of the production process, acting on behalf of the purchaser;c) the purchaser s authorized representative(s).

9 Test unitthe test unit is the number of pieces or the mass of products to be accepted or rejected together, on the basis of the tests to be carried out on sample products in accordance with the requirements of the product STANDARD or order (seeFigure 1) sample productitem (a sheet, for example) selected from a test unit for the purpose of obtaining test pieces (Figure 1) or for inspection purposesNOTEIn certain cases the sample product may be the sample samplea sufficient quantity of material taken from the sample product for the purposes of producing one or more test pieces (seeFigure 1)NOTEIn certain cases, the sample may be the sample products itself or the rough rough specimenpart of the sample having undergone mechanical treatment, followed by heat treatment where appropriate, for the purposes of producing test pieces (seeFigure 1) test piecepart of the sample, with specified dimensions, machined or unmachined, brought to a required condition for submission to a given test (seeFigure 1)NOTEIn certain cases, the test piece may be the sample itself or the rough cast (heat) analysisa chemical analysis representative of the cast (heat)

10 Determined by the steelmaker at his discretion in a manner of his product analysisa chemical analysis carried out on a sample of the sequential testinga group or series of tests from which the average and individual results are used to demonstrate that the requirements of the order and/or product STANDARD have been satisfied4 Information to be supplied by the The purchaser shall select the steel type, the shape of the product and the dimensions, taking the intended processing and use into account. He may take the manufacturer s advice in making his order shall provide all the information necessary for describing the product required and its characteristics and details concerning delivery such as:a) mass, length, area, number of pieces to be delivered;b) the product form (it may be a drawing number for example);c) the nominal dimensions;d) the tolerances on the characteristics in a), b) and c);e) the designation of the steel ;f) delivery condition (type of heat treatment, surface treatment etc);g) specific requirements for surface and/or internal quality ( ).