FARGO DTC1250e, DTC1000Me, DTC4250e, and DTCii Card ...

1 dtc1250e , dtc1000me , dtc4250e , AND DTCii card PRINTERUSER GUIDEPLT-01668 Version: 2016 Page 1-2 December 2016 PLT-01668, Version: Copyright 2014 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. This document may not be reproduced, disseminated or republished in any form without the prior written permission of HID Global GLOBAL, HID, the HID logo, and FARGO are the trademarks or registered trademarks of HID Global Corporation, or its licensors, in the and other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. MIFARE and MIFARE DESFire are registered trademarks of NXP and are used under additional offices around the world, see corporate and CorporateAsia Pacific611 Center Ridge DriveAustin, TX 78753 USAP hone: 866 607 7339 Fax:949 732 212019/F 625 King s RoadNorth Point, Island EastHong KongPhone: 852 3160 9833 Fax:852 3160 4809 Europe, Middle East and Africa (EMEA)BrazilHaverhill Business Park Phoenix RoadHaverhill, Suffolk CB9 7 AEEnglandPhone: 44 (0) 1440 711 822 Fax:44 (0) 1440 714 840 Condom nio Business Center Av.

2 Ermano Marchetti, 1435 Galp o A2 - CEP 05038-001 Lapa - S o Paulo / SPBrazilPhone: +55 11 5514-7100 HID Global Customer Support: 20161 dtc1250e , dtc1000me , dtc4250e , and DTCii card printer 1 Chapter 1: Specifications .. Regulatory Compliance .. Listings .. United States .. Canada .. Taiwan .. Japan .. Korea .. Safety Messages.. Safety Messages - United States .. Safety Messages - French .. Safety Messages - Taiwan .. Safety Messages - China .. Technical Specifications .. Functional Specifications .. printer Components: Print Ribbons .. Ribbon Types and Print Counts .. printer Components: Blank Cards .. 1-11 Chapter 2: Setup and Installation Procedures .. Choosing a Good Location .. About Moisture Condensation .. Unpacking and Inspection .. Installing the Print Ribbon Cartridge.

3 Installing the Ribbon .. Installing Blank Cards into the Input card Hopper .. card Size Selection .. Connecting the printer Power.. 2-7 Chapter 3: Print Driver Installation .. Print Driver Installation .. Driver Installation Instructions .. 3-2 Chapter 4: printer Preferences .. card Tab .. Toolbox Window .. 4-32 December 2016 PLT-01668, Version: Configuration Tab .. Calibrate Ribbon Tab .. Clean printer Tab .. Safety Messages (Review Carefully) .. Advanced Settings Tab .. Device Options Tab .. Fluorescent Panels .. Selecting the Fluorescent Panel Ribbon Type ( dtc4250e only) Creating a Custom Fluorescent Image using the YMCFKO Ribbon .. Configuring Fluorescent Data using the Application .. Image Color Tab.. Advanced Settings .. Image Calibrate.

4 Magnetic Encoding Tab .. Magnetic Track Options .. Reviewing the Sample String .. Sending the Track Data .. Overlay / Print Area .. Defining an Overlay or Print Area .. K Panel Resin Tab .. Defined Area .. Method for Defining a Single Area .. Method for Defining Multiple Areas .. printer Info.. 4-37 Chapter 5: System Overview - Troubleshooting .. Sequence of Operations .. Troubleshooting .. printer Error Buttons .. Error Messages .. Troubleshooting with the Error Message Table .. printer -Specific Tools ( dtc1250e , dtc4250e ) .. Additional printer Specific Tools .. 5-11 Chapter 6: Firmware Upgrades .. Upgrade Information.. 6-1 Chapter 7: Technical Support .. Reading the Serial Numbers on a FARGO printer .. 7-1 Appendix A: DTCii .. Locking System.

5 Accessory Procedures: Using the Security Lock Slot .. A-1 Chapter 1 December 2016 Page 1-1 SpecificationsThe purpose of this section is to provide you with specific information on the Regulatory Compliances, Agency Listings, Technical Specifications and Functional Specifications for the dtc1250e , dtc1000me , dtc4250e , and DTCii card ListingsULThe card printer is listed under UL 60950-1 (2nd edition) Information Technology EquipmentFile Number: E145118 Note: This product is intended to be supplied by a Listed Power Unit marked Class 2 and rated for 24 Vdc, printer manufacturer has been authorized by UL to represent the card printer as CSA Certified under CSA Standard No. 60950-1-07 2nd editionFile Number: E145118 FCCThe card printer complies with the requirements in Part 15 of the FCC rules for a Class A digital device. CEThe card printer has been tested and complies with EN300-330-1, EN300-330-2, EN301-489-1, EN301-489-3, EN55022 class A, EN55024, EN6100-3-2, EN6100-3-3, : Based on the above testing, the printer manufacturer certifies that the card printer complies with the following European Council Directives and has placed the CE mark on the card printer .

6 LVD 2006/95/EC, EMC 2004/108/EC, R&TTE 1999/5/EC, ROHS2 2011/65/EC EnvironmentalENERGY STAR, RoHS2, China RoHS, Power supply Efficiency level V minimumEmissions and Immunity StandardsFCC Part 15 Class A, RSS-GEN, RSS 210, CNS 13438, EN55022 Class A, EN55024, EN6100-3-2, EN6100-3-3, EN300-330-1, EN300-330-2, EN301-489-1, EN301-489-3, GB9254, GB17625 Safety StandardsUL IEC 60950-1 (2nd edition), CSA No. 60950-1-07(2nd edition), EN60950-1, GB4943, CNS14336 Additional Agency ListingsCCC, BSMI, KCPage 1-2 December 2016 SpecificationsPLT-01668, Version: StatesThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

7 These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference; in which case, you are required to correct the interference at your : Changes or modifications to an intentional or unintentional radiator not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the pr sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

8 L'exploitation est autoris e aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi, m me si le brouillage est susceptible d'en compromettre le ( AC-14019 ) 5),' ф (A ) , .December 2016 Page 1-3 PLT-01668, Version: Messages - United StatesSymbolCritical Instructions for Safety PurposesDanger:Failure to follow these guidelines results in personal injury or death. To prevent personal injury or death: Reference the following safety messages before performing an operation.

9 Always remove the power cord prior to performing repair procedures, unless otherwise specified. Ensure only qualified personnel perform these :This device is electro statically sensitive. You may damage the device if exposing it to static electricity discharges. To prevent damage: Reference the following safety messages before performing an operation. Observe all established Electrostatic Discharge (ESD) procedures while handling cables in or near the Circuit Board and Printhead Assemblies. Always wear an appropriate personal grounding device. Always remove the Ribbon and Cards from the printer before making any repairs, unless otherwise specified. Remove jewelry and thoroughly clean hands before working on the :This symbol warns of an electrical hazard that could result in personal injury or :For safety purposes, do not use Ethernet for a direct connection outside of the 1-4 December 2016 SpecificationsPLT-01668, Version: Messages - FrenchSymboleInstructions critiques visant la S curit Danger:Si ces directives ne sont pas suivies les r sultats peuvent tre des l sions corporelles ou la viter des l sions corporelles ou la mort: Rapportez-vous aux avis suivants de s curit avant de proc der une op ration.

10 Retirez toujours le c ble d alimentation avant d effectuer des proc dures de r paration, sauf sp cification contraire. Assurez-vous qu uniquement des personnes qualifi es r alisent des proc :Ce dispositif est sensible l lectricit statique. Il peut souffrir des dommages s il est expos des d charges viter des dommages: Rapportez-vous aux messages suivants avant de proc der une op ration. Suivez toutes les proc dures de D charges Electrostatiques (ESD) en vigueur durant le maniement des c bles dans ou proximit des Ensembles de Cartes de Circuit Imprim et T te d Impression. Portez toujours un dispositif de mise la terre personnelle appropri e. Retirez toujours le ruban et les Cartes de l Imprimante avant d effectuer toute r paration, sauf sp cification contraire. Retirez tous bijoux et lavez soigneusement vos mains avant de travailler l :Ce symbole est un avis de p ril lectrique passible de r sulter en l sion corporelle ou :Pour des motifs de s curit , n utilisez pas Ethernet pour une connexion directe hors du b 2016 Page 1-5 PLT-01668, Version: Messages - Taiwan 2.