Transcription of Fiberglass - Cooper Industries
1 15/8 ( )Part kg/mBFP22*Polyester ResinSolid (.94)BFV22*Vinyl Ester ResinSolid (.94)BFP22H17/8*Polyester ResinHoles in (.89)BFV22H17/8*Vinyl Ester ResinHoles in (.89)BFP22SH*Polyester ResinSlots in (.91)BFV22SH*Vinyl Ester ResinSlots in (.91)BFP22H17/8 BFV22H17/89/16 ( )holes17/8 ( )on centersBFP22 BFV22 Solid BackBFP22 THRU BFV22SH Channel lengths: 10 Ft. ( m)and 20 Ft. ( m) Fiberglass strut meets specification of ASTM D-4385 Levels III and Channel Lengths: 10 Ft. ( m)and 20 Ft. ( m) Fiberglass strut meets specification of ASTM D-4385 Levels III and ( )x 7/8 ( )slots2 ( )on centers13/16 ( )15/8 ( )31/4 ( )Part kg/mBFP22A*Polyester ResinBack To ( )BFV22A*Vinyl Ester ResinBack To ( )15/8 ( )* Insert -10 for 10 -0 ( m)length or -20 for 20 -0 ( m)length* Insert -10 for 10 -0 ( m)length or -20 for 20 -0 ( m)lengthTemperatureDesign load Multiplier75 F (24 C)100%100 F (38 C)90%125 F (52 C)78%150 F (66 C)68%175 F (79 C)60%200 F (93 C)
2 52%Published design loads on page 187 are based onusage at 70 F (21 C) and must be reduced forcontinuous exposure to higher temperatures. Refer to the chart below for high ( )BFP22 ABFV22 ASolid Back toBack13/16 ( ) Fiberglass MaterialsReference page 183 for general fitting Systems185 Field Cutting Sealant Kits Seals exposed fibers after field cutting. UV resistant RSK010 Pint Sealing Kit (473 cm3)includes sealant and brush applicatorAPPROPRIATE PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION DEVICE SHOULD BE WORN WHEN FIELD CUTTING OR GRINDING Allowable@ MaximumAllowable load @ deflection =SpanPartBeam Load1/240 Span1/360 (305)BFP221781( ) ( )1392( )928( )BFP22A2259( ) (.)
3 94)2259( )2051( )24 (609)BFP22890( ) ( )347( )231( )BFP22A1127( ) ( )767( )511( )36 (914)BFP22592( ) ( )153( )101( )BFP22A750( ) ( )338( )224( )48 (1219)BFP22443( ) ( )85( )55( )BFP22A560( ) ( )188( )123( )60 (1524)BFP22353( ) ( )53( )34( )BFP22A446( ) ( )117( )76( )72 (1829)BFP22293( ) ( )35( )22( )BFP22A370( ) ( )78( )50( )96 (2438)BFP22218( ) ( )17( )9( )BFP22A273( ) ( )39( )23( )120 (3048)BFP22172( ) ( )8( )3( )BFP22A214( ) ( )19( )9( )Beam Loading Data for Glass Reinforced Polyester ResinBeam Loading Data for Glass Reinforced Vinyl Ester ResinFiberglass MaterialsReference page 183for general fitting SystemsLoading InformationBeam Loads:The above charts list the total allowable uniform load for various simple spans based on a minimum safety factor of 2.
4 If the load is concentrated at center span, multiply the load from the above charts by and the corresponding deflection by beams should be supported in a manner to prevent rotation at supports. Long, deep beams should be tied between supportsto prevent twist. For channels with holes or slots use 90% of recommended load shown in channel loading Allowable@ MaximumAllowable load @ deflection =SpanPartBeam Load1/240 Span1/360 (305)BFV222220( ) ( )1568( )1045( )BFV22A6442( ) ( )6442( )5549( )24 (609)BFV221109( ) ( )391( )260( )BFV22A3219( ) ( )2079( )1385( )36 (914)BFV22738( ) ( )172( )114( )BFV22A2144( ) ( )922( )613( )48 (1219)BFV22553( ) ( )96( )63( )BFV22A1606( ) ( )516( )342( )60 (1524)BFV22441( ) ( )60( )39( )BFV22A1283( ) ( )327( )216( )72 (1829)BFV22366( ) ( )40( )25( )
5 BFV22A1067( ) ( )224( )147( )96 (2438)BFV22273( ) ( )19( )11( )BFV22A796( ) ( )121( )78( )120 (3048)BFV22216( ) ( )9( )7( )BFV22A633( ) ( )72( )44( )
