Example: confidence

Fisher Vee-Ball V150, V200, and V300 Rotary Control Valves

Vee-Ball V150, V200, and v300 Rotary Control ValvesThis bulletin covers the DN 25 through 600 (NPS 1through 24) V150, V200 and v300 Vee-Ball controlvalves. The Vee-Ball valve combines globe valveruggedness with the efficiency of a Rotary valve. TheVee-Ball valve is a segmented ball valve which featuresa contoured segmented V-Notch ball. A shearingaction between the V-notch ball and the ball seal(figure 1) promotes smooth, nonclogging unrestricted straight-through flow design provideshigh capacity for gas, steam, liquids, and , V200, and v300 Valves mate with a variety ofASME raised face flanges, as well as with EN flanges(see Specifications).To meet specific application requirements, a variety ofmetal and soft ball seal materials are available. Asplined drive shaft combines with a variety of poweroperated and manual actuators to provide reliable,high-performance throttling or on-off operation formany different applications in the process Trim Versatility Trim components areinterchangeable between V150, V200, and V300valves.

Consistent with pressure-temperature ratings per ASME B16.34 and EN12516-1 for the body materials shown in table 1. Specific to CW2M body material, refer to the pressure-temperature ratings shown in table 7. Do not exceed the material temperature capabilities shown below or the allowable pressure drop as shown in tables 8 and 9.

Tags:

  Control, Asme, Pressure, Temperatures, Valves, Rotary, Ratings, V002, V300, And v300 rotary control valves, Temperature ratings, Asme b16

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Fisher Vee-Ball V150, V200, and V300 Rotary Control Valves

1 Vee-Ball V150, V200, and v300 Rotary Control ValvesThis bulletin covers the DN 25 through 600 (NPS 1through 24) V150, V200 and v300 Vee-Ball controlvalves. The Vee-Ball valve combines globe valveruggedness with the efficiency of a Rotary valve. TheVee-Ball valve is a segmented ball valve which featuresa contoured segmented V-Notch ball. A shearingaction between the V-notch ball and the ball seal(figure 1) promotes smooth, nonclogging unrestricted straight-through flow design provideshigh capacity for gas, steam, liquids, and , V200, and v300 Valves mate with a variety ofASME raised face flanges, as well as with EN flanges(see Specifications).To meet specific application requirements, a variety ofmetal and soft ball seal materials are available. Asplined drive shaft combines with a variety of poweroperated and manual actuators to provide reliable,high-performance throttling or on-off operation formany different applications in the process Trim Versatility Trim components areinterchangeable between V150, V200, and V300valves.

2 This feature allows you to reduce your spareparts inventory and maintenance procedures. Theseal assembly can be changed without removingthe actuator or without removing the ball from thevalve Easy Installation Flanged body design of the V150and v300 eliminates exposed line flange bolting,reduces alignment and installation time, andpromotes secure valve installations and pipingintegrity. The V200 is available with flanges in NPS 2through Vee-Ball Valves with Fisher 2052 Actuators andFIELDVUEt DVC6200 Digital Valve ControllersVee-Ball ValvesD101363X012 Product :Vee-BallMarch 2018 Vee-Ball ValvesD101363X012 Product :Vee-BallMarch 2018 2 SpecificationsValve SizesSee table 1 Valve End Connection StylesV150: Flanged Valves that mate with CL150raised-face flanges and EN 1092-1 Type B raised-faceand Type F RecessV200: Flangeless (all sizes) and flanged Valves thatmate with CL600 raised-face flanges (NPS 2-8) v300 : Flanged Valves that mate with CL300raised-face flanges and EN 1092-1 Type B raised-faceand Type F RecessMaximum Inlet Pressures(1)V150 or v300 WCC (or Steel), CF3M ( SST), CG8M, LCC, M35-2, CK3 McuN, CD3MN,and CD3 MWCuN Valves .

3 Consistent with CL150 forV150 or CL300 for v300 pressure -temperatureratings per asme or with PNpressure-temperature ratings shown in table 1. Note: CF3M is the standard material offering inEurope and Asia-Pacific. Steel and SSTare also standard material offerings in WCC, CG8M, and LCC Valves : Consistent withapplicable pressure -temperature ratings in table 1 perASME : Consistent with applicablepressure-temperature ratings shown in table not exceed the material temperature capabilitiesshown below or the pressure drop Shutoff pressure /Temperature ratings (1)Composition ( Fisher TCM Plus or TCM Ultra), FlatMetal (NPS 3 through 12 Valves only), HD and HighTemperature HD Metal Ball Seals and Flow Ring: Seetable Classification(1) Fisher TCM Plus or Ultra Ball Seal (Forward Flow):Class VI per ANSI/FCI 70-2 and per IEC 60534-4,Flat Metal Ball Seal for NPS 3 through 12 only(Forward Flow): Class IV per ANSI/FCI 70-2 and per IEC60534-4, HD (Heavy Duty) Ball Seal (Bidirectional Flow).

4 Valve capacity; Class IV per ANSI/FCI 70-2 and IEC60534-4; Maximum allowable pressure drop inreverse flow is bar (100 psi);High Temperature HD (Heavy Duty) Ball Seal(Bidirectional Flow): Class III per ANSI/FCI 70-2 andIEC 60534-4 Flow Ring Construction (Bidirectional Flow): 5% ofvalve capacity at full travelMicro-Notch Ball with HD Seal: 4 SCFH (Leakage rateequivalent to Class IV for standard ball. This is basedon the capacity of a standard ball.)Construction MaterialsSee tables 4 and 5 Temperature Capabilities(1,2)Composition SealsFisher TCM Plus: -46 to 232_C (-50 to 450_F) Fisher TCM Ultra: -46 to 260_C (-50 to 500_F) HD Metal Seals: -46 to 288_C (-50 to 550_F)PEEK HD Seal: -46 to 232_C (-50 to 450_F)High Temperature HD Metal Seal: 288 to 427_C (550to 800_F). Contact your Emerson sales office or LocalBusiness Partner if higher temperatures are Micro-Notch Ball: -46 to 93_C (-50 to200_F)(4)Flow Ring or Flat Metal Seal : -198 to 425_C (-325 to800_F)PEEK/PTFE Bearings: -198 to 260_C (-325 to 500_F)Packing ConstructionsPTFE V-ring: -46 to 232_C (-50 to 450_F)Graphite: -198 to 538_C (-325 to 1000_F)ENVIRO-SEALt Single PTFE V-ring: -46 to 232_C (-50to 450_F) (for 100 ppm service requirements)ENVIRO-SEAL Graphite: -7 to 316_C (20 to 600_F) (for100 ppm service requirements).

5 This packingarrangement can be used to 371_C (700_F) fornon-environmental CharacteristicModified equal percentageDimensionsSee figures 7, 8, and 10 for dimensionsFace-to-Face DimensionsJStandard Face-to-Face dimensions comply with short face-to-face dimensions areavailable as an option for NPS 1 through 12 that asme short dimensions are longerthan ISA See figure 11 for dimensions.(continued) Vee-Ball ValvesD101363X012 Product :Vee-BallMarch 2018 3 Specifications (continued)Standard Flow DirectionForward (into the convex face of the V-notch ball)Flow Coefficients, Flow Coefficient Ratio(3), andNoise LevelsSee Fisher Catalog 12 Maximum Ball Rotation90 degreesActuator MountingStandard valve construction is for right-handmounting, as viewed from upstream end of (optional) mounting is available uponrequest(5)Valve/Actuator ActionWith diaphragm or piston Rotary actuator, the valve isfield-reversible between PDTC or PDTO.

6 Jpush-down-to-close (extending actuator rod closesvalve) and Jpush-down-to-open (extendingactuator rod opens valve)Approximate WeightSee table 2 OptionsJPipe plug at end of follower shaft for all sizes,JLine flange bolting, JMaterials that arecompatible with sour service, JAlloy constructionmaterials, JENVIRO-SEAL packing system: See figure6 and Bulletin :041, ENVIRO-SEAL PackingSystems for Rotary Valves (D101638X012) for moreinformation, JMicro-Notch construction for NPS 1 Valves (see Micro-Notch Construction section),JAlloy trim material , JChrome Carbide coatedinternals (NPS 2 through 12), JRotary attenuator toreduce aerodynamic noise and cavitation effects,JDouble D, Square, and Keyed shaft options1. The pressure /temperature limits in this bulletin, and any applicable code or standard limitation, should not be Additional limits are shown in tables 6, 7 and Ratio of maximum flow coefficients to minimum usable flow coefficient can also be called For the CG8M and alloy 6 Micro-Notch constructions, pressure and temperature capabilities are the same as for standard True left-hand mount is not available for Micro-Notch constructions, as it will cause the ball to rotate to the bottom of the valve of ContentsFeatures B Construction Service Attenuator Drops ValvesD101363X012 Product.

7 Vee-BallMarch 2018 4 Features (continued)n Application Versatility The Valves are available withISA and IEC 534-3-2 face-to-facedimensions as a standard construction, andoptional asme short face-to-facedimensions. IEC face-to-face dimensionsare equivalent to Long Service Life The solid HD ball seal (figures 1and 2) construction provides long service life indemanding applications. The constant wipingaction of the seal across the ball's sealing surfaceprevents scale and sludge buildup, and providesexcellent service on steam, gases, slurries, andvarious liquid Excellent Flow Control Precise contouring of theVee-Ball provides a modified equal percentage flowcharacteristic. For very precise Control of low flowrates, the Micro-Notch option is available on theNPS 1 valve. See the Micro-Notch Constructionsection of this bulletin for more Sour Service Capability Materials are available forapplications involving sour liquids and gases.

8 Theseconstructions comply with NACE MR0175-2002,MR0175-2003, MR0103, and MR0175/ISO Quick and Easy Maintenance Ball seal inspectionand replacement is done at the valve body inletwithout removing the actuator or disassembling thevalve. Valve maintenance requires no special Smooth Valve Operation Precision machined partsand pressure balanced seal designs allow smooth,precise movement of the Structural Integrity One-piece valve body improvesstructural integrity of the pressure boundary byeliminating leak paths that could be caused by thegaskets in two-piece, bolted valve Exceptional Environmental Capabilities Theoptional ENVIRO-SEAL packing systems aredesigned with very smooth shaft surfaces and liveloading to provide exceptional sealing. The seal ofthe ENVIRO-SEAL system can restrict emissions toless than the EPA (Environmental ProtectionAgency) limit of 100 ppm (parts per million).

9 Vee-Ball ValvesD101363X012 Product :Vee-BallMarch 2018 5 Table 1. Valve Body Materials, End Connections, and RatingsVALVE DESIGNVALVE BODY MATERIALSIZERATINGSNPS / DNASME / PNV150 WCCNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20, 24x20(5)CL150 WCC / (1)DN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16 LCCNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL150DN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16CF3M(2)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL150CF3 (1)DN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16R50550 NPS 1, 1-1/2, 2, 3, 4, 6CL150CG8 MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20, 24x20(5)CW2 MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12M35-2 NPS 1, 1-1/2, 2, 3, 4, 6, 8CD3MN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CD3 MWCuN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CK3 MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12V200(4)WCC, LCC, CG8M, or CF3M(2)

10 NPS 1, 1-1/2, 2CL150/300/600 flangelessNPS 3, 4CL150 and CL300/600flangelessNPS 6, 8CL150/300 and CL600flangelessNPS 10CL150 flangelessWCC, LCC, or CG8 MNPS 2, 3, 4, 6, 8CL600CW2M, M35-2, or CK3 MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8CL150/300/600 flangelessCK3 MCuNNPS 10CL150 flangelessV300 WCCNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20CL300 WCC / (1)DN 25, 40, 50PN 10-40DN 80, 100, 150PN 25-40DN 200, 250, 300PN 25 or PN 40 LCCNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL300DN 25, 40, 50PN 10-40DN 80, 100, 150PN 25-40DN 200, 250, 300PN 25 or PN 40CF3M(2)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL300CF3 (1)DN 25, 40, 50PN 10-40DN 80, 100, 150PN 25-40R50550 NPS 1, 1-1/2, 2, 3, 4, 6CL300CF3 (1)DN 200, 250, 300PN 25 or PN 40CG8 MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20CL300CW2 MNPS 1, 1-1/2, 2, 3, 4, 6, 8M35-2 NPS 1, 1-1/2, 2, 3, 4, 6, 8CD3MN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CD3 MWCuN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CK3 MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 121.


Related search queries