Fitted Frame Pre-Hanging Assembly Instructions BASE KIT

1 Fitted Frame Pre-HangingAssembly InstructionsBASE KIT base JAMB PACKAGE TO CONTAIN:1 ea. Jamb Header1 ea. Hinge Jamb1 ea. Lock Jamb1 ea. 37" Brown foam Weather Strip2 ea. 82" Brown foam Weather Strip1 ea. Pre-Hanging Hardware (excluding hinges)1 ea. Accessory Bag1 ea. Jamb Kit Installation Instructions1 ea. ThresholdBase Jamb HeaderThresholdHinge Jamb BaseLock Jamb BaseInswing: 5-5/8" Fixed VinylHandicap:1/2" x 4-9/16" AluminumOption: ADA 1/2" x 6-9/16" AluminumFRAME PREPARATION1. Frame Component SelectionSelect Frame components.

2 Figure APosition Frame on work surface. Figure B2. Assemble base FrameBend tabs down and out towards throat side of side Frame . Figure C3. Attach Fixed Vinyl or ADA ThresholdUse (4) #6 x 1-1/2" pan head type 17 screws. Figure D4. Turn Entire Preassembled Unit OverOnto Work Surface. Figure AFigure BFigure DFigure CBase JambTaylor Entrance Systems631 N. First Street West Branch, MI 48661 1PN 61270052 Rev. 1 1/29/2013 3:52 PM Page 1 Taylor Entrance Systems631 N. First Street West Branch, MI 48661 25. Attach Hinges To Frame (Use machine screwsprovided in hardware bag with your preferredhinges) Attach each hinge to hinge jamb base with(4) #10-24 x 1/2" machine screws.

3 Remove hingepin and loose hinge leaf. Figure E6. Install WeatherstripCut the 37" pcs of weatherstrip to fit between the side jambs and insert into the jamb header kerf. Trim one end of the 82" weatherstrip at an angle tooverlap the jamb header weather strip. Figure FTrim the opposite end so the weatherstrip touches the threshold. Insert weatherstrip into the same procedure for the other 82" side jamb Apply Corner Seals(1) required on hinge jamb and (1) on lock jamb. Figure G8. Attach Hinges To DoorFigure H(Hinge screws are not included with this kit)Fixed hinge doorsFigure JAttach each hinge with (4) #10 X 3/4" type 17phillips - flat head zinc plated, yellow dichromateAdjustable hinge doors Figure KAttach each hinge with (4) 10-24 X 5/8" Taptite (Tri-obular point) phillips - flat head, 82 deg.

4 Under-cut head, zinc plated, yellow dichromate heat treated. 9. Install Prehang BracketAttach with (2) #6 x 3/4" pan head truss head screws. Figure L10. Install Door Into Frame Figure MAlign hinges and insert (3) hinge Attach Prehang bracket To Frame Figure NAttach with (2) #6 x 1/2" TEK screws Figure EFigure GFigure LFigure MFigure NPainting Instructions : Frame and door should be painted within 30 (thirty) Avoid painting in cold or damp weather. Temperatureat time of painting should be between 50 F and90 Sand entire surface of Frame and door with a #320grit sand paper and wipe clean with a soft Clean Frame and door with a mild detergent solution;rinse thoroughly and let Use only an exterior acrylic latex paint on the exterior side of the door.

5 The interior side canaccept either an exterior or interior latex paint. Apply per the paint manufacturer's Do not paint the weatherstrip or HWeatherstripKerfAngle Cut End AndOverlap HeaderWeatherstripPN 61270052 Rev. 1/13 Figure J Figure KFigure 1/29/2013 3:52 PM Page 2 Fitted FrameInstallation ProceduresTRIM KIT Taylor Entrance Systems631 N. First Street West Branch, MI 48661 1 TRIM KIT PACKAGE TO CONTAIN:1 ea. Header Trim2 ea. Side Jamb Trim1 ea. Strike Hardware Bag1 ea. Trim Kit Installation InstructionsThreshold extender " > " wall size - no extender " > " wall size - 1 ea.

6 1-1/16" extender " > " wall size - 1 ea. 2" extenderNote: Handicap applications Do Not Require ExtendersROUGHOPENINGHEIGHTNet FrameHeight + 1/2"to finished floor(wood trim)*(13) ROUGHOPENINGWIDTHN ominal Doorwidth + 1"(25)ROUGHOPENINGHEIGHTI nswing 6'8" door height = 81-1/8" openingHandicap6'8" door height = 80-5/8" opening(Net Frame height plus 1/2")ROUGHOPENINGWIDTH3'0" door width = 37" opening2'8" door width = 33" opening2'6" door width = 31" opening(Nominal door width plus 1")Metal Stud / DrywallFrame Fastener.

7 Type "S" Bugle HeadSelf-Tapping ScrewWood Stud / DrywallFrame Fastener:1-1/4" Course ThreadDrywall Screws1. Prepare OpeningThoroughly caulk floor area where the unit will be located with a high grade caulking. Caulk entire joint between Frame and threshold. Figure C2. Install Prehung Unit Into Wall OpeningSet clearances and attach to wall using the recommended fasteners. Figure A3. Install Trim PiecesInstall trim pieces making sure the trim goes between the stop return and each individual weld plate of the base Attach to wall using the recommended fasteners.

8 3. Install Threshold ExtenderFigure AFigure CFigure BPainting Instructions : Frame and door should be painted within 30 (thirty) Sand entire surface of Frame and door with a #320grit sand paper and wipe clean with a soft Clean Frame and door with a mild detergent solution; rinse thoroughly and let Use only an exterior acrylic latex paint on the exterior side of the door. The interior side canaccept either an exterior or interior latex paint. Applyper the paint manufacturer's " < " = 2" " < " = 3" " < " = 4"Trim PiecesPrehung Doorin base JambCaulkPN 61270053 Rev.

9 1 1/29/2013 3:53 PM Page 3