Fittings and Accessories - SKF.com

1 Fittings and AccessoriesFor oil and grease. For Centralized Lubrication Systems and General Use22 This brochure provides an overview of metallic pipe unions for luid brochure is divided into the sections Accessories for tubes and hoses SKF Quick Connectors for pressures up to 300 bar and 350 bar Solderless pipe unions with cutting sleeve acc. to DIN EN ISO 8434-1 and DIN 2353, DIN EN ISO 9974-1/DIN 2353 and elastomer washer Tubes and hoses Accessories ReservoirsDimensions in and AccessoriesCAD models for the products shown in this brochure can be downloaded at: for tubes and hoses .. 4 20 for solderless pipe union with tapered sleeve acc.

2 To DIN 3862 Adaptors .. 7, 8 Banjo ittings .. 10, 11 Bracketed connectors .. 15 Bulkhead connectors .. 14 Cable strap .. 19 Connectors .. 14 Counterbores .. 4 Cross joints .. 17 Double tapered sleeves .. 5 Elbows .. 9, 14 Elbow bulkhead ittings .. 14 Fixing bolts .. 20 Fixing clips .. 18 Flat washers .. 12 Form counterbores .. 4 Hexagon nuts .. 20 Lock washer .. 20 Mounting base .. 19 Pipe bracket .. 19 Reducing adapters .. 8 Reinforcing sockets .. 6 Screw plugs .. 12 Socket unions .. 5, 6 Straight bulkhead .. 14 Tapered sleeves .. 6 Tee connectors .. 16 Threaded sockets .. 13 Tube-to-tube-connector .. 15 Vent plugs.

3 12 Distributor manifolds .. 21 24 for solderless pipe union with tapered sleeve acc. to DIN 3862 SKF quick connectors for pressures up to 300 bar .. 25 27 Adaptors .. 25 Banjo ittings .. 26 Check valves .. 27 Connectors .. 27 Elbows .. 27 Locking pin .. 27 SKF quick connectors for pressures up to 350 bar .. 28 29 Adaptors .. 28 Banjo ittings .. 28 Check valves .. 29 Elbows .. 28 Straight screw-in connectors .. 28 Tee screw-in connector .. 29 Fittings .. 30 36 for solderless pipe union with cutting-sleeve acc. to DIN EN ISO 8434-1 / DIN 2353 Banjo ittings .. 33 Connectors for pressure gauges .. 34 Cutting sleeves.

4 30 Elbow bulkhead connectors .. 32 Elbow connectors .. 32 Elbow female thread unions .. 35 Elbow screw-in connectors .. 33 Four-way connectors .. 34 L-screw-in connectors .. 32 Reducing connections .. 36 Reducing connectors .. 32 Straight bulkhead connectors .. 32 Straight connectors .. 30 Straight screw-in connectors .. 31 Straight screw-in itting .. 35 Straight screw-in glands .. 30 Tee connectors .. 34 Tee female thread unions .. 35 Tee screw-in connectors .. 34 Union nuts .. 30 Fittings .. 37 39 for solderless pipe union with cutting-sleeve acc. to DIN EN ISO 9974-1/DIN 2353 and elastomer washerConnectors for pressure gauges.

5 38 Cone plugs .. 39 Reducing connectors .. 37 Screw plugs .. 39 Straight bulkhead connectors .. 37 Straight connectors .. 37 Straight screw-in connectors .. 37 Tee connectors .. 38 Vent plugs .. 39 Tubes and hoses .. 40 47 Hoses .. 46, 47 High pressure hoses .. 41 43, 45 Plastic tubing .. 41, 43 44 Self-installation of high pressure hoses .. 45 Steel tubing .. 40 Tube bending device .. 40 Accessories .. 48 56 Banjo ittings .. 51 Check valves .. 53 Coupling plugs .. 49 Coupling socket .. 49 Filler coupling .. 48 Lever-type grease gun .. 56 Oil trough .. 56 Pressure gauges .. 50 Quick-disconnect couplings.

6 48 Relief valves .. 52 Rotating joints .. 51 Topping-up pumps .. 56 Safety valves .. 53, 54 Shut-off valves .. 55 Reservoirs .. 57, 58 Metal reservoirs .. 58 Oil level gauge .. 58 Plastic reservoirs .. 57 Index .. 59 65 Contents44T3T2T4D490 RD5D6 Accessories for tubes and hosesSolderless pipe union with tapered sleeve acc. to DIN 3862. For pressures up to 45 bar CounterboresDIN 3854/DIN 3862 for solderless tube connectionSpeciication of counterboresTube D5B11D6D4T3T2T4R1102 1)2,52,51,5M6 0,754,55,58,51,31404443M8 16,58,512,51,61406664,5M10 179141,61408886,5M14 1,5911,518,51,6141010108,5M16 1,5911,519,51,61412121210,5M18 1,59,512221,61) not shown in DIN standardImportant note #3: When using a hand drill, take care not to tilt the counterbore out of the drill axis.

7 To avoid damages drill steadily without interrup-tion. Increase pressure slightly at the counterboresto tap ports for solderless tube connection Form counterbore for counter-twist drillOrder boreL1D1D2D6D3T12 902-1112,5110260,5101,554,55,5904-411414 04651036,57,58,5906-411614066612104,58,5 89908-4118140870166,51210,511,5910-41110 141072188,51410,511,5912-411121412752010 ,5161112 Provision of counterbore Figure 1D3T2T1D6 Figure 1 Provision of counterbore predrill holes bore hole counterbore with form to be tapped counterbore up to the stopForm counterbore enlarges bore hole diam. d4 to core hole for ISO counterbore!55 DAccessories for tubes and hosesSolderless pipe union with tapered sleeve acc.

8 To DIN 3862. For pressures up to 45 bar Double tapered sleeves DIN 3862 Order tube DBrass402-001 1)2,5404-0014406-0016408-0018410-0011041 2-00112 Stainless steel404-001-S34406-001-S36408-001-S38D1 L2L1 Socket unions DIN 3871 Order tube D1L1L2 SeriesSteel, galvanized surface402-002 1)2,5M6 0,75937404-0024M8 11248LL406-0026M10 113410408-2028M14 1,5164,514L410-00210M16 1,5175,517412-00212M18 1,518619 Stainless steel404-002-S34M8 11248406-002-S36M10 113410408-002-S38M14 1,5164,514 Double tapered sleevesSocket unionsInstallation (steel and copper tubing)1 Push socket union and double tapered sleeve onto tube Insert tube end into tapped port up to the First tighten socket union inger-tight by hand.

9 Then turn another 1 1/2 tapered sleeveSocket unionSolderless pipe union 1) not shown in DIN standardLL-series (extra light version), L-series (light version)66L1D2D1 Accessories for tubes and hosesSolderless pipe union with tapered sleeve acc. to DIN 3862. For pressures up to 45 bar Tapered sleeves DIN 3862 Order tube sockets (if plastic tubing is used) Order socketTapered sleeveD1L2L1 Socket unionSocket unions DIN 3871 Order tube D1L1L2 Steel, galvanized 11248406-6126M10 113410408-6128M14 11248406-612-MS6M10 113410408-612-MS8M14 sleeveReinforcing socketSocket unionSolderless pipe union (plastic tubing)Installation (plastic tubing)1 Insert reinforcing socket into plastic Push socket union and tapered sleeve onto tube Insert tube end into counterbored port up to the First tighten socket union inger-tight by hand.

10 Then turn another 1 1/2 for tubes and hosesSolderless pipe union with tapered sleeve acc. to DIN 3862. For pressures up to 45 bar L1L2 D2D1 AdaptorAdaptors with cylindrical thread to DIN 71428 (sealed by lat washer to DIN 7603)Order D1D2L1L2 Steel, galvanized 1M8 1241411404-005M8 1/8 A18814404-162M12 118917404-164M14 1M10 119917406-054G 1/4 A201017301-005M14 3/8 A211022408-0048M10 1M14 1/8A29817408-160G 1/4 A301617408-162M12 129917301-020G 1/4 A231017301-001M14 1M16 131919410-163G 1/4 A301019410-164M14 1/4 A521619410-004M16 1/2 A241227410-022M22 1M18 1/4A351022412-164M14 1/4 A411622412-004M18 with cylindrical thread to DIN 71428 (sealed by lat washer to DIN 7603)