Example: bachelor of science

Flange Insul Kits

C A L P I C OFLANGE INSULATION KITSFOR WATER, NATURAL GAS, PETROLEUM AND OTHER PIPE sizes 1/2" thru 96"TYPE E Full Face GasketTYPE F Ring GasketTYPICAL STANDARD kits includes:* Type E (full face) gasket 1/8" thick -or-* Type F (ring) gasket 1/8" thick* High-density polyethylene sleeves 1/32"* Laminated phenolic washers 1/8"* Steel backup washers 1/8"Two sets of phenolic & steel washers are required when two sides are AS FOLLOWS:* Series 15 - 150# Class through 2,500#* Standard Gasket (4)* Special 's and Special 'sOptions & Specifications For Calpico Flange Insulation kits :* Isolate cathodically protected lines. * Eliminate stray electrical currents in piping. * Sectionalize piping systems.* Effectively seal a Flange as a gasket. 650 588-2241**NOTE: When using plain phenolic Flange kits , we recommend using a 1/32" or 1/16" back-up gasket on each side of the phenolic gasket for better MATERIAL: (FF or Ring)OPTION #1: 1/8" Phenolic manufactured from laminated phenolic sheet.

FLANGE INSULATION C A L P I C O KITS FOR WATER, NATURAL GAS, PETROLEUM AND OTHER PIPE LINES. Flange sizes 1/2" thru …

Tags:

  Flange, Kits, Sunil, Flange insul kits

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Flange Insul Kits

1 C A L P I C OFLANGE INSULATION KITSFOR WATER, NATURAL GAS, PETROLEUM AND OTHER PIPE sizes 1/2" thru 96"TYPE E Full Face GasketTYPE F Ring GasketTYPICAL STANDARD kits includes:* Type E (full face) gasket 1/8" thick -or-* Type F (ring) gasket 1/8" thick* High-density polyethylene sleeves 1/32"* Laminated phenolic washers 1/8"* Steel backup washers 1/8"Two sets of phenolic & steel washers are required when two sides are AS FOLLOWS:* Series 15 - 150# Class through 2,500#* Standard Gasket (4)* Special 's and Special 'sOptions & Specifications For Calpico Flange Insulation kits :* Isolate cathodically protected lines. * Eliminate stray electrical currents in piping. * Sectionalize piping systems.* Effectively seal a Flange as a gasket. 650 588-2241**NOTE: When using plain phenolic Flange kits , we recommend using a 1/32" or 1/16" back-up gasket on each side of the phenolic gasket for better MATERIAL: (FF or Ring)OPTION #1: 1/8" Phenolic manufactured from laminated phenolic sheet.

2 Temperature: up to 225 strength: 500 volts per strength: 24,000 absorbance: ASTM #2: 1/8" Neoprene-faced : up to 175 strength: same as phenolic strength: same as phenolic absorbance: same as phenolic #3: 1/8" Fiberglas : up to 280 strength: 550 volts per strength: 50,000 absorbance: strength: 45,000 Mll-P-18177 & NEMA Grade #4: Non-Asbestos Klinger # : up to 400 F constantTensile strength: 2,000 psi ASTM #5: Non-Asbestos Garlock # : up to 400 F constantMax pressure: 1000 psiOPTION #6: G-10 with O-ring.(see Option #3 for specifications.)OPTION #7: Phenolic with O-ring.(see Option #1 for specification.)** Higher operating pressure will lower maximum temperature rating.**PLEASE CONSULT FACTORY FOR APPLICATIONS INVOLVING STEAM, OR cont.:SLEEVE MATERIAL:Option #1: 1/32" wall high density polyethylene. Temperature: up to 175 : 80,000 psiTensile strength: 150,000 psiWater absorbance: #2: 1/32" wall spiral-wound : up to 300 strength: 4,000 volts per absorption: #3: 1/32" wall phenolic tubing.

3 Specs same as gasket #4: One-piece sleeve and washer combination. 1/32" sleeve wall and 5/32" thickness washer #5: 1/32" wall Fiberglas epoxy tubing. Same specs as gasket #6: High temperature Nomex and other special sleeve material available on WASHERS:Option #1: 1/8" phenolic, specs same as gasket #2: 1/8" dielectric asbestos, specs same as gasket #3: Fiberglas epoxy, specs same as gasket #4: High temperature and special material available on WASHERS:Option #1: 1/8" thick steel made to fit within bolt facing on ASA standard #2: Stainless steel available on , San Mateo Ave.; So. San Francisco, CA 94080650 588-2241 ph --- 650 873-6952 fax


Related search queries