Fully Sealed Potentiometer Professional Grade - Vishay

1 Sfernice Revision: 01-Feb-181 Document Number: 51037 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Sealed Potentiometer Professional GradeDESIGN SUPPORT TOOLSFEATURES High power rating 3 W at 70 C Low temperature coefficient (150 ppm/ C typical) Cermet element Full sealing Use of faston connections Tests according to CECC 41000 or IEC 60393-1 Wires and connectors available Custom design on request Center detent option Material categorization.

2 For definitions of compliance please see REFERENCE DATAM ultiple moduleNoSwitch modulen/aDetent moduleYesSpecial electrical lawsA: linear, L: logarithmic, F: reverse logarithmicSealing levelIP 67 Lifespan25K cyclesclick logo to get startedAvailableModelsDIMENSIONS in millimeters (inches) mm ( ")20 ( ) ( )8 ( ) ( )13 ( ) wrenchThread M10 x 6 ( )76 R ( )acb3 ( ) ( ) ( )FG = 16 ( )FL = 25 ( )FR = 50 ( )3( ) ( )3( ) ( ) ( ) ( ) ( )PE30LL: LPRP - Locating ( ) ( ) ( )PANEL MOUNTPE30ME: Panel Sealed ( ) 6 ( )FlatslocatedFP = 47 ( )FJ = 22 ( )FD = 13 ( )9 ( )Sealing ring8 ( ) ( ) ( ) 1 ( ) ( )16 ( ) ( ) MOUNTSlot 1 x Sfernice Revision: 01-Feb-182 Document Number: 51037 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

3 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT SPECIFICATIONSR esistive elementCermetElectrical travel270 10 Resistance rangelinear taper22 to 10 M logarithmic taper100 to M Standard series E31 - - and on request 1 - 2 - 5 Tolerancestandard 20 %on request 10 % to 5 %TaperPower ratinglinear logarithmic3 W at 70 C W at 70 CCircuit diagramTemperature coefficient (typical) 150 ppm/ CLimiting element voltage300 VContact resistance variation (typical)3 % Rn or 3 End resistance (typical)1 Dielectric strength (RMS)2500 VInsulation resistance (300 VDC)105 M Independent linearity (typical) 5 %100806040200010080604020% CLOCKWISE SHAFT ROTATION% TOTAL RESISTANCE FLAAMBIENT TEMPERATURE IN CPOWER IN W0204060 70 80100 120 14003 LIN.

4 TAPER A12 LOG. TAPER L and Fa(1)b(2)c(3) Sfernice Revision: 01-Feb-183 Document Number: 51037 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT RESISTANCE ELEMENT DATASTANDARDRESISTANCEVALUESLINEAR TAPERLOGS 70 70 WIPER SPECIFICATIONSM echanical travel300 5 Operating torque / typical value3 stop torque120 Ncm lb torque of mounting nut250 Ncm lb-inch weight23 g to 32 g oz. to : pure SnENVIRONMENTAL SPECIFICATIONST emperature range-55 C to +125 CClimatic category55/125/56 SealingFully Sealed - container IP67 OPTIONSS pecial feature command shaftLength is measured from the mounting surface to the free end of the shaft.

5 The screwdriver slot is aligned with the wiper within 10 . Special shafts are available, in accordance to drawings supplied by customers. We recommend that customers should not machine tool shafts, in order to avoid damage. Bending or torsion of terminals should also be sealing (PE30M)The panel sealing device consists of a ring located in a groove on the Potentiometer face. Sealing is obtained by tightening the ring against the panel when mounting the Potentiometer . Old code: PE30 PLocating peg (PE30LL)Location is obtained by fitting a special washer on the mounting face of the Potentiometer . Old code: LPRPS haft locking (PE30LD)The shaft locking device consists of a tapered nut tightening a slotted notched washer against both bushing and shaft.

6 DBAN tightening torque is 200 Ncm, shaft locking torque being 30 is also available with all special device is normally supplied in a separate bag. Can be pre-mounted on Method1)2) wrench12 Sfernice Revision: 01-Feb-184 Document Number: 51037 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Nothing stated herein shall be construed as a guarantee of quality or durabilityCENTER DETENT Stable position in mid mechanical travel Output ratio 50 % 10 % Rotational life.

7 10 000 actuationsORDERING INFORMATION (First order only)MARKING Vishay trademark Part number (including ohmic value and tolerance code) Manufacturing date code Marking of terminals 3, and a, b, cPERFORMANCETESTSCONDITIONSTYPICAL VALUES AND DRIFTS RT/RT (%) R1-2/R1-2 (%)OTHERE lectrical endurance1000 h at rated power90'/30' - ambient temp. 70 C 1 %-Contact res. variation: < 3 % RnClimatic sequencePhase A dry heat 125 CPhase B damp heatPhase C cold -55 CPhase D damp heat 5 cycles % 1 %-Damp heat, steady state56 days40 C 93 % HR % 1 %Insulation resistance: > 104 M Change of temperature5 cycles-55 C at +125 C %--Mechanical endurance25 000 cycles 3 %-Contact res.

8 Variation: < 2 % RnShock50 g s at 11 ms3 successive shocksin 3 directions % %-Vibration10 Hz to 55 mm or 10 g sduring 6 h % %-Full CWFull Sfernice Revision: 01-Feb-185 Document Number: 51037 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (part number)MODEL BUSHINGOPTIONSHAFTOHMICVALUETOLERANCETAP ERPACKAGINGSPECIALNUMBERPE30L = M10 x = panelsealedM10 x = noneFor L bushingD = DBANL = LPRPB = DBANand LPRPFor M bushingE = pegA = peg and DBANFor L bushing (= old codes:)FG 16 mm, slotted = ACFL 25 mm, slotted = AMFR 50 mm, plain = ALFor M bushingFD = 13 mm, slotted = ACFJ = 22 mm, slotted = AMFP = 47 mm, plain = ALA law = from 22 to 10 M L and F laws = from 100 to M M = 20 %On request.

9 K = 10 %J = 5 %A = linearL = clockwise logarithmicF = clockwise inverse logarithmicB = box of 10 pieces(if applicable)Given byVishayfor customdesignorE105CV1 MPART NUMBER DESCRIPTION (for information only)PE30 LPRPAC200K 20 %ADBANCV1 MBOe3 MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGINGCUSTOMSHAFTSPECIALLEAD(Pb)-FREE RELATED DOCUMENTSAPPLICATION NOTESP otentiometers and for Vishay Sfernice Resistive and Inductive Disclaimer Revision: 08-Feb-171 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

10 Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability.