G y M Codes HAAS TORNO mejorado - …

1 T cnico: +(504) 237-4360 (Honduras) haas LATHEPREPARATORY FUNCTIONSG74 FACE GROOVING, or HIGH SPEED PECK DRILL CYCLE (X,Z,U,W,I,K,D,F) (SETTING 22)G75 PECK GROOVING CYCLE or (X,Z,U,W,I,K,D,F) (SETTING 22)G76 THREADING CYCLE, MULTIPLE PASS (X,Z,U,W,I,K,D,A,P,F) (SETTING 86,95,96,99)G77**LIVE TOOLING FLATTING CYCLE (I,J,L,R,S,K)G80*CANCEL CANNED CYCLE (SETTING 56)G81 DRILL CANNED CYCLE (X,Z,W,R,F)G82 SPOT DRILL / COUNTERBORE CANNED CYCLE (X,Z,W,P,R,F)G83 PECK DRILL DEEP HOLE CANNED CYCLE (X,Z,W,I,J,K,Q,P,R,F) (SETTING 22, 52)G84 TAPPING CANNED CYCLE (X,Z,W,R,F)G85 BORE IN~BORE OUT CANNED CYCLE (X,Z,U,W,R,L,F)G86 BORE IN~STOP~RAPID OUT CANNED CYCLE (X,Z,U,W,R,L,F)G87 BORE IN~STOP~MANUAL RETRACT CANNED CYCLE (X,Z,U,W,R,L,F)G88 BORE IN~DWELL~MANUAL RETRACT CANNED CYCLE (X,Z,U,W,P,R,L,F)G89 BORE IN~DWELL~BORE OUT CANNED CYCLE (X,Z,U,W,P,R,L,F) / TURNING CYCLE, MODAL (X,Z,U,W,I,F)G92 THREADING CYCLE, MODAL (X,Z,U,W,I,F) (SETTING 95, 96)G94 END FACING CYCLE, MODAL (X,Z,U,W,K,F)G95**LIVE TOOLING END FACE RIGID TAP (X,Z,W,R,F)G96 CONSTANT SURFACE SPEED, CSS ON (S)G97*CONSTANT NON-VARYING SPINDLE SPEED, CSS OFF (S) (SETTING 56)G98 FEED PER MINUTE (F)G99*FEED PER REVOLUTION (F) (SETTING 56)G100 MIRROR IMAGE CANCEL G101G101 MIRROR IMAGE (X,Z) (SETTING 45, 47)G102 PROGRAMMABLE OUTPUT TO RS-232 (X,Z)G103 LIMIT BLOCK LOOKAHEAD (P0 - P15 max.)

2 For number control looks ahead)G105**SERVO BAR COMMANDG110-G111 WORK OFFSETPOSITIONING COORDINATE #7- #8G112** CARTESIAN TO POLAR TRANSFORMATIONG113** CARTESIAN TO POLAR TRANSFORMATION CANCELG114-G129 WORK OFFSET POSITIONING COORDINATE #9 - #24G154 SELECT WORK OFFSET POSITIONING COORDINATE P1-99 (P)G159**BACKGROUND PICKUP / PART RETURNG160**APL AXIS COMMAND ONG161**APL AXIS COMMAND OFFG184 REVERSE TAPPING CANNED CYCLE (X,Z,W,R,F)G186**LIVE TOOLING REVERSE RIGID TAPG187 ACCURACY CONTROL FOR HIGH SPEED MACHINING (E) (SETTING 85)G194 SUB-SPINDLE / TAPPING CANNED CYCLEG195**LIVE TOOLING RADIAL TAPPING (X,F)G196**LIVE TOOLING RADIAL TAPPING REVERSE (X,F)G200 INDEX ON THE FLY (X,Z,U,W,T)G00*RAPID POSITIONING MOTION (X,Z,U,W,B) (SETTING 10, 56, 101)G01 LINEAR INTERPOLATION MOTION (X,Z,U,W,B,F)G01 LINEAR MOTION, CHAMFER AND CORNER ROUNDING (X,Z,U,W,B,I,K,R,A,F)G02CW CIRCULAR INTERPOLATION MOTION (X,Z,U,W,I,K,R,F)G03 CCW CIRCULAR INTERPOLATION MOTION (X,Z,U,W,I,K,R,F)G04 DWELL (P) (P=seconds.

3 Milliseconds)G05**FINE SPINDLE CONTROL MOTION (X,Z,U,W,R,F) (LIVE TOOLING)G09 EXACT STOP, NON-MODALG10 PROGRAMMABLE OFFSET SETTING (X,Z,U,W,L,P,Q,R)G14**MAIN-SPINDLE / SUB-SPINDLE SWAPG15**MAIN-SPINDLE / SUB-SPINDLE SWAP CANCELG17**CIRCULAR MOTION XY PLANE SELECTION LIVE TOOLING (G02,G03)G18*CIRCULAR MOTION ZX PLANE SELECTION (G02,G03) (SETTING 56)G19**CIRCULAR MOTION YZ PLANE SELECTION LIVE TOOLING (G02,G03)G20*VERIFY INCH COORDINATE POSITIONING (SETTING 9 needs to be INCH)G21 VERIFY METRIC COORDINATE POSITIONING (SETTING 9 needs to be METRIC)G28 RAPID TO MACHINE ZERO RETURN THRU REF. POINT (X,Z,U,W,B) (Fanuc)G29 MOVE TO LOCATION THROUGH G29 REF. POINT (X,Z) (Fanuc)G31**FEED UNTIL SKIP FUNCTION (X,Z,U,W,F)G32 THREAD CUTTING PATH, MODAL (X,Z,U,W,F)G40*TOOL NOSE COMPENSATION CANCEL G41/G42 (X,Z,U,W,I,K) (SETTING 56)G41 TOOL NOSE COMPENSATION, LEFT (X,Z,U,W) (SETTING 43, 44, 58)G42 TOOL NOSE COMPENSATION, RIGHT (X,Z,U,W) (SETTING 43, 44, 58)G50 SPINDLE SPEED MAXIMUM RPM LIMIT (S)G51 RAPID TO MACHINE ZERO, CANCEL OFFSET (Yasnac)G52 WORK OFFSET POSITIONING COORDINATE (SETTING 33, YASNAC)G52 GLOBAL WORK OFFSET COORDINATE SYSTEM SHIFT (SETTING 33, FANUC)G53 MACHINE ZERO POSITIONING COORDINATE, NON-MODAL (X,Z,B)G54*WORK OFFSET POSITIONING COORDINATE #1 (SETTING 56)

4 G55 WORK OFFSET POSITIONING COORDINATE #2G56 WORK OFFSET POSITIONING COORDINATE #3G57 WORK OFFSET POSITIONING COORDINATE #4G58 WORK OFFSET POSITIONING COORDINATE #5G59 WORK OFFSET POSITIONING COORDINATE #6G61 EXACT STOP, MODAL (X,Z)G64*EXACT STOP G61 CANCEL (SETTING 56)G65**MACRO SUB-ROUTINE CALLG70 FINISHING CYCLE (P,Q) / STOCK REMOVAL CYCLE (P,Q,U,W,I,K,D,S,T,R1,F) (SETTING 72, 73)G72 END FACE STOCK REMOVAL CYCLE (P,Q,U,W,I,K,D,S,T,R1,F) (SETTING 72, 73)G73 IRREGULAR PATH STOCK REMOVAL CYCLE (P,Q,U,W,I,K,D,S,T,F)MODALNON-MODALDEFAU LT *OPTION**Note: These G and M Codes are useful reference information, on a desk, or at the 're great to have laminated with G Codes on one side and M Codes on the a suggestion; get some white 90lb. cardstock and print G- Codes on one side and M- Codes onthe other. Cut out the square section and go to Kinko's copies or local printer to get them , September 29, 2010+(504) 2237-4360M00 PROGRAM STOP (SETTING 42, 101)M01 OPTIONAL PROGRAM STOP (SETTING 17)M02 PROGRAM ENDM03 SPINDLE ON FORWARD (S) (SETTING 144)M04 SPINDLE ON REVERSE (S) (SETTING 144)M05 SPINDLE STOPM08 COOLANT ON (SETTING 32)M09 COOLANT OFFM10 CHUCK CLAMP (SETTING 92)M11 CHUCK UNCLAMP (SETTING 92)M12**AUTO AIR JET ON (P)M13**AUTO AIR JET OFFM14**MAIN SPINDLE CLAMPM15**MAIN SPINDLE UNCLAMPM17 ROTATE TURRET FORWARD (T) (SETTING 97)M18 ROTATE TURRET REVERSE (T) (SETTING 97)M19**ORIENT SPINDLE (Optional P,R)M21**TAILSTOCK ADVANCE (SETTING 93, 94, 106, 107, 121, 145)M22**TAILSTO C K R E T R A C T (SETTING 105)M23 ANGLE OUT OF THREAD ON (SETTING 95, 96)

5 M24 ANGLE OUT OF THREAD OFFM25-M28 OPTIONAL USER M code INTERFACE WITH M-FIN SIGNALM30 PROGRAM END AND RESET (SETTING 2, 39, 56, 83)M31 CHIP AUGER FORWARD (SETTING 114, 115)M33 CHIP AUGER STOPM36**PA R T S C AT C H E R O NM37**PA R T S C ATCHER OFFM38 SPECIFY SPINDLE VARIATION ON (SETTING 165, 166)M39 SPECIFY SPINDLE VARIATION OFF (SETTING 165, 166)M41 SPINDLE LOW GEAR OVERRIDEM42 SPINDLE HIGH GEAR OVERRIDEM43 TURRET UNLOCK (FOR SERVICE USE ONLY)M44 TURRET LOCK (FOR SERVICE USE ONLY)M51-M58 OPTIONAL USER M code SETM59 OUTPUT RELAY SET (N) haas LATHEMISCELLANEOUS FUNCTIONSM61-M68 OPTIONAL USER M code CLEARM69 OUTPUT RELAY CLEAR (N)M76 PROGRAM DISPLAYS INACTIVEM77 PROGRAM DISPLAYS ACTIVEM78 ALARM IF SKIP SIGNAL FOUNDM79 ALARM IF SKIP SIGNAL NOT FOUNDM85**AUTOMATIC DOOR OPEN (SETTING 51, 131)M86**AUTOMATIC DOOR CLOSE (SETTING 51, 131)M88**HIGH PRESSURE COOLANT ON (SETTING 32)M89**HIGH PRESSURE COOLANT OFFM93**AXIS POSITION CAPTURE START (P,Q)M94**AXIS POSITION CAPTURE STOPM95 SLEEP MODE (hh.)

6 Mm)M96 JUMP IF NO SIGNAL (P,Q)M97 LOCAL SUB-ROUTINE CALL (P,L)M98 SUB-PROGRAM CALL (P,L)M99 SUB-PROGRAM/ROUTINE RETURN OR LOOP (P) (SETTING 118)M109**INTERACTIVE USER INPUT (P)M110** TAILSTOCK CHUCK CLAMP (SETTING 122)M111**TAILSTO C K C H U C K U N C L A M P (SETTING 122)M119**SUB-SPINDLE ORIENT (P,R)M121-M128 OPTIONAL USER M code INTERFACE WITH M-FIN SIGNALM133**LIVE TOOL DRIVE FORWARD (P)M134**LIVE TOOL DRIVE REVERSE (P)M135**LIVE TOOL DRIVE STOPM143**SUB-SPINDLE FORWARD (P)M144**SUB-SPINDLE REVERSE (P)M145**SUB-SPINDLE STOPM154**C AXIS ENGAGE (SETTING 102)M155**C AXIS DISENGAGEM164**ROTATE APL GRIPPERS TO "n" POSITION (Pn)M165**OPEN APL GRIPPER 1 (RAW MATERIAL)M166**CLOSE APL GRIPPER 1 (RAW MATERIAL)M167**OPEN APL GRIPPER 2 (FINISHED MATERIAL)M168**CLOSE APL GRIPPER 2 (FINISHED MATERIAL)All M Codes are effective or cause an action at the end of the block and only one M code is allowed in each 1-01-06 OPTION**Note: These G and M Codes are useful reference information, on a desk, or at the 're great to have laminated with G Codes on one side and M Codes on the a suggestion; get some white 90lb.

7 Cardstock and print G- Codes on one side and M- Codes onthe other. Cut out the square section and go to Kinko's copies or local printer to get them MILLPREPARATORY FUNCTIONSG00*RAPID POSITIONING MOTION (X,Y,Z,A,B) (SETTING 10, 56, 101)G01 LINEAR INTERPOLATION MOTION (X,Y,Z,A,B,F)G02 CIRCULAR INTERPOLATION MOTION CW (X,Y,Z,A,I,J,K,R,F)G03 CIRCULAR INTERPOLATION MOTION CCW (X,Y,Z,A,I,J,K,R,F)G04 DWELL (P) (P=seconds"."milliseconds)G09 EXACT STOP, NON-MODALG10 PROGRAMMABLE OFFSET SETTING (X,Y,Z,A,L,P,R)G12CW CIRCULAR POCKET MILLING (Z,I,K,Q,D,L,F)G13 CCW CIRCULAR POCKET MILLING (Z,I,K,Q,D,L,F)G17*CIRCULAR MOTION XY PLANE SELECTION (G02 or G03) (SETTING 56)G18 CIRCULAR MOTION ZX PLANE SELECTION (G02 or G03)G19 CIRCULAR MOTION YZ PLANE SELECTION (G02 or G03)G20*VERIFY INCH COORDINATE POSITIONING (SETTING 9, set to INCH)G21 VERIFY METRIC COORDINATE POSITIONING (SETTING 9 set to METRIC)G28 MACHINE ZERO RETURN THRU REF.

8 POINT (X,Y,Z,A,B) (SETTING 108)G29 MOVE TO LOCATION THROUGH G28 REF. POINT (X,Y,Z,A,B)G31**FEED UNTIL SKIP FUNCTION (X,Y,Z,A,B,F)G35**AUTOMATIC TOOL DIAMETER MEASUREMENT (D,H,Z,F)G36**AUTOMATIC WORK OFFSET MEASUREMENT (X,Y,Z,A,B,I,J,K,F)G37**AUTOMATIC TOOL LENGTH MEASUREMENT (D,H,Z,F)G40*CUTTER COMP CANCEL G41/G42/G141 (X,Y)G412D CUTTER COMPENSATION, LEFT (X,Y,D) (SETTING 40, 43, 44, 58)G422D CUTTER COMPENSATION, RIGHT (X,Y,D) (SETTING 40, 43, 44, 58)G43 TOOL LENGTH COMPENSATION+ (H,Z) (SETTING 15)G44 TOOL LENGTH COMPENSATION- (H,Z) (SETTING 15)G47 TEXT ENGRAVING (X,Y,Z,R,I,J,P,E,F,) (Macro Variable 599 Change Serial #)G49*TOOL LENGTH COMPENSATION CANCEL G43/G44/G143 (SETTING 56)G50*SCALING G51 CANCEL (SETTING 56)G51**SCALING (X,Y,Z,P) (SETTING 71)G52 WORK OFFSET POSITIONING COORDINATE (SETTING 33, YASNAC)G52 GLOBAL WORK COORDINATE OFFSET SHIFT (SETTING 33, FANUC)

9 G52 GLOBAL WORK COORDINATE OFFSET SHIFT (SETTING 33, haas )G53 MACHINE ZERO XYZ POSITIONING, NON-MODAL (X,Y,Z,A,B)G54*WORK OFFSET POSITIONING COORDINATE #1 (SETTING 56)G55 WORK OFFSET POSITIONING COORDINATE #2G56 WORK OFFSET POSITIONING COORDINATE #3G57 WORK OFFSET POSITIONING COORDINATE #4G58 WORK OFFSET POSITIONING COORDINATE #5G59 WORK OFFSET POSITIONING COORDINATE #6G60 UNI-DIRECTIONAL POSITIONING (X,Y,Z,A,B) (SETTING 35)G61 EXACT STOP, MODAL (X,Y,Z,A,B)G64*EXACT STOP G61 CANCEL (SETTING 56)G65**MACRO SUB-ROUTINE CALLG68**ROTATION (G17,G18,G19,X,Y,Z,R) (OPTION) (SETTING 72, 73)G69*ROTATION G68 CANCEL (SETTING 56)G70 BOLT HOLE CIRCLE with a CANNED CYCLE (I,J,L)G71 BOLT HOLE ARC with a CANNED CYCLE (I,J,K,L)G72 BOLT HOLES ALONG AN ANGLE with a CANNED CYCLE (I,J,L)MODALNON-MODALDEFAULT *OPTIONAL **G73 HIGH SPEED PECK DRILL CANNED CYCLE (X,Y,A,B,Z,I,J,K,Q,P,R,L,F) (SETTING 22, 52)G74 REVERSE TAPPING CANNED CYCLE (X,Y,A,B,Z,J,R,L,F) (SETTING 130, 133)G76 FINE BORING CANNED CYCLE (X,Y,A,B,Z,I,J,P,Q,R,L,F) (SETTING 27)G77 BACK BORE CANNED CYCLE (X,Y,A,B,Z,I,J,Q,R,L,F) (SETTING 27)G80*CANCEL CANNED CYCLE (SETTING 56)G81 DRILL CANNED CYCLE (X,Y,A,B,Z,R,L,F)G82 SPOT DRILL / COUNTERBORE CANNED CYCLE (X,Y,A,B,Z,P,R,L,F)G83 PECK DRILL DEEP HOLE CANNED CYCLE (X,Y,A,B,Z,I,J,K,Q,P,R,L,F) (SETTING 22, 52)G84 TAPPING CANNED CYCLE (X,Y,A,B,Z,J,R,L,F) (SETTING 130, 133)G85 BORE IN~BORE OUT CANNED CYCLE (X,Y,A,B,Z,R,L,F)G86 BORE IN~STOP~RAPID OUT CANNED CYCLE (X,Y,A,B,Z,R,L,F)G87 BORE IN~MANUAL RETRACT CANNED CYCLE (X,Y,A,B,Z,R,L,F)G88 BORE IN~DWELL~MANUAL RETRACT CANNED CYCLE (X,Y,A,B,Z,P,R,L,F)

10 G89 BORE IN~DWELL~BORE OUT (X,Y,A,B,Z,P,R,L,F)G90*ABSOLUTE POSITIONING COMMANDG91 INCREMENTAL POSITIONING COMMAND (SETTING 29)G92 GLOBAL WORK COORDINATE SYSTEM SHIFT (FANUC) ( haas ) (SETTING 33)G92 SET WORK COORDINATE VALUE (YASNAC) (SETTING 33)G93 INVERSE TIME FEED MODE ONG94*INVERSE TIME FEED MODE OFF / FEED PER MINUTE ON (SETTING 56)G95 FEED PER REVOLUTION (SETTING 9, 56)G98*CANNED CYCLE INITIAL POINT RETURN (SETTING 56)G99 CANNED CYCLE "R" PLANE RETURNG100 MIRROR IMAGE G101 CANCELG101 MIRROR IMAGE (X,Y,Z,A,B) (SETTING 45, 46, 47, 48, 80)G102 PROGRAMMABLE OUTPUT TO RS-232 (X,Y,Z,A,B)G103 LIMIT BLOCK LOOKAHEAD (P0-P15 for number control looks ahead)G107 CYLINDRICAL MAPPING (X,Y,Z,A,Q,R,)G110-G129 WORK OFFSET POSITIONING COORDINATE #7-26G136**AUTOMATIC WORK OFFSET CENTER MEASUREMENTG1413D+ CUTTER COMPENSATION (X,Y,Z,I,J,K,D,F)G143**5-AXIS TOOL LENGTH COMPENSATION+ (X,Y,Z,A,B,H) (SETTING 15, 117)G150 GENERAL PURPOSE POCKET MILLING (X,Y,P,Z,I,J,K,Q,D,R,L,S,F)G153**5-AXIS HIGH SPEED PECK DRILL CANNED CYCLE (X,Y,A,B,Z,I,J,K,Q,P,E,L,F) (SETTING 22)G154**SELECT WORK OFFSET POSITIONING COORDINATE P1-99 (P)G155**5-AXIS REVERSE TAPPING CANNED CYCLE (X,Y,A,B,Z,J,E,L,F)G161**5-AXIS DRILL CANNED CYCLE (X,Y,A,B,Z,E,L,F)G162**5-AXIS SPOT DRILL / COUNTERBORE CANNED CYCLE (X,Y,A,B,Z,P,E,L,F)G163**5-AXIS PECK DRILL CANNED CYCLE (X,Y,A,B,Z,I,J,K,Q,P,E,L,F) (SETTING 22)G164**5-AXIS TAPPING CANNED CYCLE (X,Y,A,B,Z,J,E,L,F)G165**5-AXIS BORE IN, BORE OUT CANNED CYCLE (X,Y,A,B,Z,E,L,F)