Genie AWP-25S SOP Aerial Work Platform - …

1 Standard Operating ProcedureIssuedReviewed PageOct. 26/06 Oct. 26/06 1/1 Approved by:Department ofPhysical PlantGenie AWP-25 SAerial Work PlatformSOP002D. Boyce1 Purpose & ScopeThe purpose of this procedure is to ensure that all operators can safely and effectively use the Genie AWP-25 SAerial Work IntroductionThe Genie AWP-25S is an AC-powered personnel lift designed to vertically elevate a single operator up to 25 into the air to perform maintenance , repair and construction activities. Given the potential hazards associated withworking at heights, all personnel required to use the Genie AWP-25S must first be trained to operate it safely Training RequirementsThe training program for the Genie AWP-25S contains the following TheoryThe Genie AWP Super Series Operator s Manual is the primary training document for the AWP-25S .

2 Alloperators must read each section of the manual in detail and then review the information with a competent personto ensure Practical Training After completing the operator s manual review, each operator must receive practical instruction on the safe andeffective use of the Genie AWP-25S . During this practical instruction, all operators must set-up and use theGenie- AWP-25S as detailed in the operator s manual. 4 DocumentationThe Task Matrix (below) must be used to ensure that all training elements have been completed. As each task iscompleted and the operator demonstrates comprehension and competency, the competent person providing thetraining will place a check mark in the box beside the task.

3 When all tasks have been completed and both theoperator and the competent person are satisfied that the operator can now safely and effectively use the GenieAWP-25S, then both the operator and competent person will sign and date the matrix in the space provided. Acopy of this signed and dated operating procedure will then be placed in the operator s training file to provideproof of completion of RulesN/A2 Controls3 Legend 4 Pre-operation Inspection5 Maintenance6 Function Tests7 Workplace Inspection8 Operating Instructions9 Battery Charging InstructionsN/AN/A10 Transport Instructions11 Tilt-back Operation InstructionsN/AN/A12 Decals13 SpecificationsN/AName (please print)DateName (please print)DateOperatorSignatureReviewerSigna tureOperator sManualwith maintenance InformationSecond EditionSecond PrintingPart No.

4 82910 Genie AWP Super SeriesPart No. 82910 Operator s ManualSecond Edition Second PrintingCopyright 1996 by Genie IndustriesFirst Edition: Eighth Printing, October 2001 Second Edition: Second Printing, April 2004" Genie " and "AWP" are registered trademarksof Genie Industries in the and many othercountries. "Super Series" is a trademark of machine complies withANSI/SIA Printed on recycled paperPrinted in , understand and obey these safety rules andoperating instructions before operating this trained and authorized personnel shall bepermitted to operate this machine.

5 This manual shouldbe considered a permanent part of your machine andshould remain with the machine at all times. If youhave any questions, call Genie 9 Pre-operation 12 Function 15 Workplace 18 Operating 19 Battery Charging 21 Transport 22 Tilt-back Operation 32 Contact us:Internet: : No. 82910 Genie AWP Super Series1 Operator s ManualSecond Edition Second PrintingSafety RulesDangerFailure to obey the instructions andsafety rules in this manual will causedeath or serious Not Operate Unless:You learn and practice the principles of safemachine operation contained in this operator' Avoid hazardous and understand the safety rulesbefore going on to the next Always perform a pre-operation Always perform function tests prior to Inspect the Only use the machine as it was read, understand and obey themanufacturer's instructions and safety rules safety and operator's manuals and machinedecalsYou read, understand and obey employer'ssafety rules and worksite regulationsYou read.

6 Understand and obey all applicablegovernmental regulationsYou are properly trained to safely operate first time this machine is set up for use, abreather cap is installed. See Pre-operationInspection AWP Super SeriesPart No. 82910 Operator s ManualSecond Edition Second PrintingTip-over HazardsDo not raise the Platform unless the base is level,all four outriggers are properly installed and theleveling jacks firmly contact the not adjust or remove the outriggers while theplatform is occupied or not move the machine while the Platform not place ladders or scaffolds in the Platform oragainst any part of this not place or attach overhanging loads to anypart of this not transport tools and materials unless they areevenly distributed and can be safely handled by theperson in the RULESDo not raise the Platform unless the machine islevel.

7 Do not set the machine up on a surfacewhere it cannot be leveled using only the not cause a horizontal force or side load to themachine by raising or lowering a fixed oroverhanging not push off or pull toward any object outsidethe allowableside force45 lbs / 200 NDo not use the machine ona moving or mobilesurface or No. 82910 Genie AWP Super Series3 Operator s ManualSecond Edition Second PrintingDo not operate the machine in strong or gustywinds. Do not increase the surface area of theplatform or the load. Increasing the area exposed tothe wind will decrease machine , equipment and materials shall notexceed the maximum Platform capacity (all models except Canada)AWP-15S350 lbs159 kgAWP-20S350 lbs159 kgAWP-25S350 lbs159 kgAWP-30S350 lbs159 kgAWP-36S350 lbs159 kgAWP-40S300 lbs136 kgMaximum capacity (models sold in Canada only)

8 AWP-15S300 lbs136 kgAWP-20S300 lbs136 kgAWP-25S300 lbs136 kgAWP-30S300 lbs136 kgAWP-36S300 lbs136 kgAWP-40S300 lbs136 kgMaximum occupancy1 personDo not operate the machine near drop-offs, holes,bumps, debris, unstable or slippery surfaces orother possible hazardous not alter or disable machine components that inany way affect safety and not replace items critical to stability with itemsof different weight or specification. Use only Genieauthorized replacement not push the Genie AWP from the Platform sideof the moving the machine with a forklift or othertransport vehicle, the Platform should be fullylowered, the machine should be turned off and nopersonnel shall remain in the HazardsThe guard rail system provides fall protection.

9 Ifoccupants of the Platform are required to wearpersonal fall protection equipment (PFPE) due tojob site or employer rules, PFPE equipment and itsuse shall be in accordance with the PFPE manufacturer s instructions and applicablegovernmental not sit, stand or climbon the Platform guard a firm footing onthe Platform floor at not exit the platformwhile raised. If a powerfailure occurs, haveground personnel activatethe manual lowering the Platform floor clear of the Platform entry mid-rail or gate RULES4 Genie AWP Super SeriesPart No. 82910 Operator s ManualSecond Edition Second PrintingElectrocution HazardsThis machine, even with an optional fiberglassplatform, is not electrically insulated and will notprovide protection from contact with or proximity toelectrical away from the machine if it contactsenergized power lines or becomes electricallycharged.

10 Personnel on the ground or in the platformmust not touch or operate the machine untilenergized power lines are shut safe distances from electrical power linesand apparatus in accordance with applicablegovernmental regulations and the following SafeVoltageApproach DistancePhase to PhaseFeet Meters0 to 300 VAvoid Contact300V to to to to to to RULESA llow for Platform movement, electrical line swayor sag and movement due to strong or gusty not use the machine as a ground for not operate an AC powered machine or a DCbattery charger unless using a 3-wire groundedextension cord connected to a grounded AC not alter or disable 3-wire grounded HazardsOperators must comply with employer.