GMA131 Aggregate - opakboya.com.tr

1 GMA131 Aggregate Non Slip Aggregate Page No. 1 of 4 PRODUCT DESCRIPTION Crushed, dried, non sparking Aggregate manufactured using blue flint deposits INTENDED USES As a non slip Aggregate for use in combination with a recommended coating to form a non-slip system suitable for use on decks, walkways etc. PRACTICAL INFORMATION FOR GMA131 Colour Light grey to blue-black Gloss Level N/A Volume Solids 100% Typical Thickness 300 500 m Theoretical Coverage N/A Practical Coverage Allow appropriate loss factors Method of Application Roller Drying Time Dependant upon paint system used. Refer to appropriate datasheet REGULATORY DATA Flash Point N/A Product Weight kg/l VOC N/A GMA131 Aggregate Non Slip Aggregate Page No.

2 2 of 4 SURFACE PREPARATION The surface to be coated must be clean and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:1992. Accumulated dirt and soluble salts must be removed. Dry bristle brushing will normally be adequate for accumulated dirt. Soluble salts should be removed by fresh water washing. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Unprimed Surfaces Abrasive blast clean to Sa2 (ISO 8501-1:1988) or SSPC-SP6. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. A surface profile of 50-75 microns (2-3 mils) is recommended.

3 Primed Surfaces Recommended primers should be applied in accordance with the relevant product datasheet. Primed surfaces should be dry and free from all contamination, and should be overcoated according to the intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc., should be prepared to the specified standard ( Sa2 (ISO 8501- 1:1988) or SSPC SP6, Abrasive Blasting, or SSPC SP11, Power Tool Cleaning) and patch primed prior to overcoating. APPLICATION GMA131 can be incorporated in to the coating system by either pre-mixing or broadcasting Pre- mixing method 1. Refer to appropriate product data sheet. - Agitate Base (Part A) with a power agitator. - Add appropriate quantity of GMA131 to the Base (Part A) and mix thoroughly with a power agitator.

4 - Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with a power agitator. 2. Immediately apply by roller the mixed product onto the prepared surface 3. Once the unit has been mixed it must be used within the working pot life of the paint used. Broadcast method 1. Compatible products should be mixed and applied in accordance with the relevant datasheet. GMA131 Aggregate should be liberally broadcast to blind the wet surface. 2. Ensure surrounding areas are kept dust free. 3. For large areas it is suggested that bands of material are applied and the process is repeated until coverage is complete. Following cure the system should be firmly brushed with a wide broom to remove any loose and poorly adherent Aggregate .

5 Excess Aggregate can be collected and reused providing it has not been contaminated with moisture etc. The surface should be dry and free from all contamination before application of a topcoat. Suitable topcoats should be applied within the recommended overcoating intervals using a long haired roller to fully encapsulate the Aggregate . Mix Ratio Pre-mixing method : per 5lt of paint Broadcast method : Typically 2 kg/ sqm. Working Pot Life Refer to appropriate product datasheet. Airless Spray Not recommended Air Spray (Pressure Pot) Not recommended Brush Suitable small areas only Roller Recommended Thinner Appropriate for paint system used Cleaner Appropriate for paint system used Work Stoppages Do not allow material to remain in hoses, gun or spray equipment.

6 Thoroughly flush all equipment with appropriate cleaner. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean Up Clean all equipment immediately after use with appropriate cleaner. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation. GMA131 Aggregate Non Slip Aggregate Page No. 3 of 4 PRODUCT CHARACTERISTICS A coating system containing GMA 131 will provide a non-slip finish, suitable for light medium or heavy traffic.

7 A typical system containing GMA 131 has been tested and does not support a spark with sufficient energy to detonate combustion in an explosive atmosphere. Test report available on request. SYSTEM COMPATIBILITY GMA131 can be used with a limited range of high performance products including: Interseal 670 HS Interzone 954 Intergard 740 For other suitable products, consult International Protective Coatings. GMA131 Aggregate Non Slip Aggregate Page No. 4 of 4 ADDITIONAL INFORMATION Further information regarding industry standards, terms and abbreviations used in this data sheet can be found in the following sections of the International Protective Coatings data manual: x Definitions & Abbreviations x Surface Preparation x paint Application x Practical & Theoretical Coverage Individual copies of these information sections are available upon request.

8 SAFETY PRECAUTIONS This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS) which International Protective Coatings has provided to its customers. All work involving the application and use of this product should be performed in compliance with all relevant national, Health, Safety & Environmental standards and regulations. In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

9 If in doubt regarding the suitability of use of this product, consult International Protective Coatings for further advice. PACK SIZE kg unit International GMA131 in a plastic container 5lt unit International GMA131 5lt in a 5lt container For availability of other pack sizes contact International Protective Coatings. SHIPPING WEIGHT Shipping No. kg unit 5lt unit Non Hazardous STORAGE Shelf Life 24 months minimum at 25qC (77qF). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. The information given in this sheet is not intended to be exhaustive and any person using the product for any purpose other than that specifically recommended in this sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk.

10 Any warranty, if given, or specific Terms & Conditions of Sale are contained in International s Terms & Conditions of Sale, a copy of which can be obtained on request. Whilst we endeavour to ensure that all advice we give about the product (whether in this sheet or otherwise) is correct we have no control over either the quality or condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of the use of the product.