Example: air traffic controller

Good Luck SAM - networktut.com

Client1 Ping :(T01)OSPFA uthenticationYesR4:(T11)Redistributeospf OSPF-> eigrp to OSPF_to_EIGRPR4:(T14) eigrp PassiveInterfaceYesNoRead the scenarioR1 Ping ipv6 R3(s0/0 ipv62026::1:2R1 Ping ipv6 R4(tunnel ipv6 addr)2026::34:2R2: (T12) IPv6: enableospf0R3: (T15) IPv6:removetunnel mode ipv6R4: (T16) missingRedistribution from RIPngtoOSPFv3 YesYesNoNoIPV4 IPV6R1:(T03) Wrong IP of BGPN eighbor (.56 should be .65)R1: ip nat outside should be replaced with ip nat insideR1:(T05)WAN ACLM issing command under the outside edge security ACLAdd networkR1Sh run andcheck`Check if there is wrongBGB StatementCheck the Edge access-list statementR4Sh ip eigrp NeighborYesNoDSW1 ShrunCheck VlanFilterstatementDSW1:(T06) VLAN filterYesASW1:(T08) Access port not in VLAN10and should be added under the interfaceASW1:(T09) Port Channel not allowing VLAN10,200 ASW1Sh run Ship intbrASW1:(T07) Port SecurityDownNoASW1 ShvlanUPVlan is notokVlan is OkDSW1:ip helper-address should match R4 (DHCP server) helper-addressYesNoGood LuckSAMSAMSAMSAMGood LuckSAMSAMSAMSAMNEWNEWNEWR1: Missing command under the outside ACL NAT_TrafficAdd networkCheck the Edge access-list statement)

Client1 Ping10.1.1.1 Client1 Ping10.1.1.2 Yes No Client1 ping10.2.1.1 No R1 :(T01)OSPF Authentication Yes R4 :(T11)Redistributeospf OSPF->EIGRP to OSPF_to_EIGRP

Tags:

  Fpso, Eigrp

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Advertisement

Transcription of Good Luck SAM - networktut.com

1 Client1 Ping :(T01)OSPFA uthenticationYesR4:(T11)Redistributeospf OSPF-> eigrp to OSPF_to_EIGRPR4:(T14) eigrp PassiveInterfaceYesNoRead the scenarioR1 Ping ipv6 R3(s0/0 ipv62026::1:2R1 Ping ipv6 R4(tunnel ipv6 addr)2026::34:2R2: (T12) IPv6: enableospf0R3: (T15) IPv6:removetunnel mode ipv6R4: (T16) missingRedistribution from RIPngtoOSPFv3 YesYesNoNoIPV4 IPV6R1:(T03) Wrong IP of BGPN eighbor (.56 should be .65)R1: ip nat outside should be replaced with ip nat insideR1:(T05)WAN ACLM issing command under the outside edge security ACLAdd networkR1Sh run andcheck`Check if there is wrongBGB StatementCheck the Edge access-list statementR4Sh ip eigrp NeighborYesNoDSW1 ShrunCheck VlanFilterstatementDSW1:(T06) VLAN filterYesASW1:(T08) Access port not in VLAN10and should be added under the interfaceASW1:(T09) Port Channel not allowing VLAN10,200 ASW1Sh run Ship intbrASW1:(T07) Port SecurityDownNoASW1 ShvlanUPVlan is notokVlan is OkDSW1:ip helper-address should match R4 (DHCP server) helper-addressYesNoGood LuckSAMSAMSAMSAMGood LuckSAMSAMSAMSAMNEWNEWNEWR1: Missing command under the outside ACL NAT_TrafficAdd networkCheck the Edge access-list statement)


Related search queries