Guardmaster 440C-CR30 Configurable Safety Relay Building ...

1 Quick Start Guardmaster 440C-CR30 Configurable Safety Relay Building Block Connected Components Accelerator Toolkit Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards. Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.

2 If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. In no event will rockwell automation , Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, rockwell automation , Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by rockwell automation , Inc.

3 With respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of rockwell automation , Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of Safety considerations. WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss.

4 Attentions help you identify a hazard, avoid a hazard, and recognize the consequence. IMPORTANT Identifies information that is critical for successful application and understanding of the product. Labels may also be on or inside the equipment to provide specific precautions. SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash.

5 Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL. Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). allen - bradley , CompactLogix, Connected Components Workbench, Guardmaster , Micro800, Micro820, Micro830, Micro850, PanelView, PowerFlex, ProposalWorks, PS/2, rockwell automation , rockwell Software, and Stratix are trademarks of rockwell automation , Inc. Trademarks not belonging to rockwell automation are property of their respective companies. Where to Start To complete your Building block project, follow this path.

6 Read the Getting Started CCAT with System Design Assistant Quick Start, publication CC-QS035. Chapter 1 - Guardmaster 440C-CR30 Configurable Safety Relay Setup Chapter 2 - System Validation rockwell automation Publication CC-QS038A-EN-P - August 2015 3. Where to Start Notes: 4 rockwell automation Publication CC-QS038A-EN-P - August 2015. Table of Contents Preface About This Publication.. 7. Terminology.. 8. Available Connected Components Accelerator Toolkit Building Blocks .. 9. Additional Resources .. 9. Chapter 1. Guardmaster 440C-CR30 Before You Begin .. 11. Configurable Safety Relay Setup What You Need.

7 11. Follow These Steps .. 12. Connect the USB Cable to the Safety Relay .. 13. Configure the Communication Settings .. 13. Review the 440C-CR30 Software Configurable Safety Relay Quick Start Guide.. 14. Chapter 2. System Validation Before You Begin .. 15. What You Need .. 15. Follow These Steps .. 16. Review the System Overview .. 17. Configure the Controller Communication Ports .. 19. Configure the PanelView 800 Terminal Communication Settings.. 20. Connect Your Devices.. 22. Download Your Program to the Controller .. 22. Configure the IP Address of Your PanelView 800 Terminal .. 26. Transfer Your HMI Application to the PanelView 800 Terminal.

8 26. Validate Your System.. 28. Understand the Machine Functions Screen .. 28. Set Up the Configuration Screen .. 28. Understand the Status Screen .. 30. Understand the Fault Screens .. 32. Verify the Configuration Screens .. 33. Verify the Status Screen .. 34. Troubleshoot a Wiring Fault .. 36. Appendix A. 440C-CR30 Configurable Safety Relay .. 39. User-defined Function Block Appendix B. Global Variables .. 43. rockwell automation Publication CC-QS038A-EN-P - August 2015 5. Table of Contents Notes: 6 rockwell automation Publication CC-QS038A-EN-P - August 2015. Preface About This Publication The Guardmaster 440C-CR30 Configurable Safety Relay Building block monitors the status of the 440C-CR30 Safety Relay through a Modbus RS-232C interface.

9 This quick start provides instructions for how to connect the Micro800 . programmable logic controller (PLC) with the Safety Relay for status updates. Use this quick start to configure a monitoring system for your 440C-CR30 Safety Relay . To help with the design and installation of your system, application files and other information are provided on the Connected Components Accelerator Toolkit (CCAT). The CCAT provides bills of materials (BOM), CAD drawings for panel layout and wiring, control programs, human machine interface (HMI) screens, and more. With these tools and the built-in best-practices design, you are free to focus on the design of your machine control and not on design overhead tasks.

10 The CCAT is available on the Connected Components Accelerator Toolkit DVD, publication CC-QR002, or through the rockwell automation Software Download and Registration System (SDRS) site at The beginning of each chapter contains the following information. Read these sections carefully before you begin work in each chapter: Before You Begin - The chapters in this quick start do not have to be completed in the order in which they appear. However, this section defines the minimum amount of preparation that is required before completing the current chapter. What You Need - This section lists the tools that are required to complete the steps in the current chapter, including, but not limited to, hardware and software.