H360-36/48HD SERIES TECHNICAL GUIDE - Hyster

1 SERIESTECHNICAL GUIDEH360-36/48HD DIMENSIONSC ircled dimensions correspond to the line numbers on the tabulated chart inside the TECHNICAL GUIDE . Dimensions are in inches (millimeters).4-214-354-41-51-64-14-14-5 4-24-71-94-204-194-321-84-31H360-36/48HD SPECIFICATIONSCERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI , as required by OSHA Section (a)(2) and also comply with Part III ANSI in effect at time of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck. Performance specifications are for a truck equipped as described under Standard Equipment on this TECHNICAL GUIDE . Performance specifications are affected by the condition of the vehicle and how it is equipped, as well as by the nature, condition of the operating area, proper service and maintenance of the vehicle. If these specifications are critical, the proposed application should be discussed with your designationH360-36 HDH360-36 HDH360-48 HDH360-48HD1-5 Rated load capacitylbskg36,00016,32936,00016,3291-6 Load centerinmm369144812191-8 Load ,7501483,750 WEIGHTS2-1 Total truck weight without loadlbskg47,18621,40350,493 22,9032-2aAxle loading with loadfrontlbskg77,11034,97779,90336,2432- 2brearlbskg6,0762,7566,5902,9712-3aAxle loading without loadfrontlbskg23,81710,80323,68310,7422- 3brearlbskg23,36910,60026,80912,160 WHEELS3-1 Tire typePneumaticPneumatic3-2 Tire BiasDIMENSIONS4-1 Mast tilt, forward / backdegrees15 / 1015 / 104-2 Height of mast loweredinmm1453,6801453,6804-3 Freelift (Top of Fork)inmm00004-4 Lift height (Top of Fork)

2 Inmm1563,9841563,9844-5 Height of mast extendedinmm2225,6222225,6224-7 Height to top of operator compartmentinmm1203,0541203,0544-19 Overall lengthinmm3107,8783107,8784-20 Length to load faceinmm2145,4382145,4384-21 Overall width over drive tiresinmm1002,5421002, ,440962,4404-24 Carriage widthinmm1002,5401002,5404-25aFork spread, min (in-in)inmm923592354-25bFork spread, max (out-out)inmm9423759423754-31 Ground clearance, under mast with loadinmm718771874-32 Ground clearance, center of wheelbaseinmm14368143684-33 Minimum aisle width (add load length + clearance)inmm2365,9842365,9844-35 Outside turning radiusinmm2055,1992055, tank capacitygall42160421608-8 Fuel tank capacitygall542065420610-4 DEF tank TIER 4 FINAL CUMMINS QSB ENGINE5-1aTravel speedwith loadmphkm/h172717275-1bwithout loadmphkm/h182918295-2aLifting speedwith loadft/ loadft/ speedwith loadft/ loadft/ pull MaxlbskN26,70011926,5001195-7 Gradeability no load / rated load 1 mph ( km/h)%35/3135/3133/3333/33 PERFORMANCEWITH TIER 3 CUMMINS QSB ENGINE5-1aTravel speedwith loadmphkm/h172717275-1bwithout loadmphkm/h182918295-2aLifting speedwith loadft/ loadft/ speedwith loadft/ loadft/ pull MaxlbskN24,50011324,3001135-7 Gradeability no load / rated load 1 mph ( km/h)%35/2735/2733/2633/26H360-36/48HD SPECIFICATIONSRATED CAPACITIESM odel H360-36HD: 36,000 lbs.

3 At 36 (16,329 kg at 914 mm) load centerModel H360-4 8HD: 36,000 lbs. at 4 8 (16,329 kg at 1220 mm) load centerRated capacities are for trucks equipped with: 2-Stage mast to 156 (3984 mm) maximum fork height 100 (254 0 mm) carriage width 96 (24 4 0 mm) long forks Contact your dealer for other capacity Factor: = mm 1 lb = kgPOWERTRAINSUNITSTIER 4 FINALTIER 31-3 Power typeDieselDiesel7-1 Engine Manufacturer / modelCummins QSB QSB Tier ComplianceTier 4 FinalTier 37-2aEngine power output - RatedhpkW1641221551167-2bEngine power output - PeakhpkW1681251551167-3 Governed speedrpm2,3002,3007-4 Number of cylinders / displacement# / l6 torque - Maxlb-ftN-m5407324436007-5aTurbochargerT ypeVariable Geometry, Water CooledWastegate7-8 Alternator outputAmps1201208-0 Transmission Manufacturer / modelZF WG-161ZF WG-1618-1 Transmission type & speedsPowershift 3F x 3 RPowershift 3F x 3R7-10 Battery voltage, rated capacityV / CCA2 x 12 / 9002 x 12 / 9007-10aDrive Axle Manufacturer / modelKessler D81 Kessler D815-10 Service brakeOil immersed (wet) discOil immersed (wet) disc5-11 Park brakeSpring apply, dry discSpring apply, dry disc10-1 Working pressure for attachmentspsiMpa2, , flow for MAST Lift height (Top of Fork)

4 Mast Lowered Freelift (Top of Fork) Overall Extended NO FREE-LIFT (NO FL)1563984145368000222562218045941573984 0024662322125406173439000278704424462191 894797003107858 NOTE: Higher capacity rated versions up to 40,000 lbs. at shorter load centers are available upon request on a custom basis. Please contact Hyster Company for details & SPED 25000 30000 35000 40000 24 28 32 36 40 44 48 52 56 60 64 68 72 RATED LOAD (lbs) LOAD CENTER (in) H360-36HD H360-48HD RATED LOAD vs. LOAD CENTERDFSSFP CARRIAGE w/ QD CUSTOMARY20000 25000 30000 35000 40000 24 28 32 36 40 44 48 52 56 60 64 68 72 RATED LOAD (lbs) LOAD CENTER (in) H360-36HD H360-48HD RATED LOAD vs. LOAD CENTERAPRON SIDE SHIFT PIN TYPE CUSTOMARY20000 25000 30000 35000 40000 24 28 32 36 40 44 48 52 56 60 64 68 72 RATED LOAD (lbs) LOAD CENTER (in) H360-36HD H360-48HD RATED LOAD vs. LOAD CENTERSTD PIN TYPE CUSTOMARYRATED LOAD (lbs)LOAD CENTER (in)RATED LOAD (lbs)RATED LOAD (lbs)40000400004000035000350003500030000 30000300002500025000250002000024 28 32 36 40 44 48 52 56 60 64 68 72200002000020000 25000 30000 35000 40000 24 28 32 36 40 44 48 52 56 60 64 68 72 RATED LOAD (lbs) LOAD CENTER (in) H360-36HD H360-48HD RATED LOAD vs.

5 LOAD CENTERDFSSFP CARRIAGE w/ INTEGRATED CUSTOMARYLOAD CENTER (in)LOAD CENTER (in)LOAD CENTER (in)24 28 32 36 40 44 48 52 56 60 64 68 7224 28 32 36 40 44 48 52 56 60 64 68 7224 28 32 36 40 44 48 52 56 60 64 68 72 RATED LOAD (lbs)4000035000300002500020000H360-48HD+ H360-36HD+H360-48 HDH360-36 HDH360-36HD+H360-48HD+H360-36 HDH360-48 HDH360-48HD+H360-36HD+H360-48 HDH360-36 HDH360-36HD+H360-48HD+H360-36 HDH360-48 HDSTANDARD FEATURES AND OPTIONSMASTSM asts with nested channels provide maximum visibility of the attachment and load. Mast channels, rollers, stub shafts and chain anchors are reinforced to provide good torsional rigidity. Oversized stub shafts are inset and double welded for good impact resistance. Chains designed on outside of mast to enhance visibility ; integral pin-type fork positioner with simultaneous or individual fork control; pin-type integral sideshift; integral pin-type dual function sideshift fork positioner; apron style sideshift fork positioner with simultaneous or individual fork control.

6 Overall width is 100 (2540 mm) for the H360-36/48 HDMinimum inside-to-inside fork spacing - model and attachment dependent is 9 (235 mm)Maximum outside-to-outside fork spacing - model and attachment dependent is 94 (2375 mm)FORKST hree kinds of forks are offered in two PIN T YPE - STANDARD PROFILE available in: 96 long x x (2440mm x 100mm x 200mm) 96 long x x (2440mm x 90mm x 250mm)ii. INTEGR AL PIN T YPE (FOR USE WITH DFSSFP) available in: 96 long x x (2440mm x 100mm x 200mm) 96 long x x (2440mm x 90mm x 250mm)iii. QD HOOK T YPE (FOR USE WITH DFSSFP - QUICK DISCONNECT) available in: 96 long x x (2440mm x 100mm x 200mm) 96 long x x (2440mm x 90mm x 250mm)STANDARD ENGINE - TIER 4 FINALQSB 6 cylinder diesel engine delivers 164 hp (peak 168 hp) and 540 lb-ft of maximum torque. EPA Tier 4 Final compliant engine features cooled exhaust gas recirculation (EGR) technology with selective catalytic reduction (SCR); water-cooled variable geometry turbocharger with an integrated Diesel Exhaust Fluid (DEF) delivery system.

7 Innovative selectable ECO performance modes offer excellent fuel economy and maximum productivity. Also includes: 120 amp alternator Viscous, on-demand cooling fan which saves fuel and reduces noise Low mount exhaust with diesel oxidation catalyst (DOC) and a diluter to reduce exhaust temperatures Requires ultra-low sulfur diesel fuel and low-ash oil Heavy duty spinner type Sy-Klone pre-cleaner center stacked for ease of service and enhanced visibilityTRANSMISSION ZF WG-161 three-speed, fully reversing powershift transmission produces smooth shifting, precise inching and fast acceleration 3 forward and 3 reverse gears Smooth fully automatic gear shift control Powershift transmission with proportional valves Inching electronically controlled Cushioned clutch lock-up provides smooth shifting and dampens drive line shock loads Simple push button calibration Transmission lock-out preventing high speed directional changes Transmission and engine powertrain protection for excessive engine coolant temperature, low engine oil pressure, and excessive engine inlet air temperaturesELECTRICAL SYSTEM Sealed Deutsch connectors CANbus system for easy diagnostics of engine.

8 Transmission and hydraulicsHYDRAULIC SYSTEM Hyster on-demand load sensing hydraulic system introduces an efficient way to meet truck s hydraulic load demands: Based on Variable Displacement Pump (VDP) technology Pump is only pumping when oil is needed Less heat is produced - oil and filters last longer. Hoses, seals, and components also wear less and last longer Engine runs quieter and at lower speeds, extending life of major components Leak free O-Ring Face Seal (ORFS) fittings standard throughout the truck Capable of more oil displacement even at low engine speedsSTEERING SYSTEM Designed for high loads and long life, the one piece axle frame carries the axle loads and provides mounting for the spindles and cylinder Axle spindles are supported by oil bathed wheel bearings and sealed to prevent contamination entry or loss of oil. This ensures that oil bearings are always lubricated and enhances overall durability of the axle spindles No steering linkage adjustments are required.

9 Lubricating fittings on tie rod pins are the only regular maintenance points Load sensed steering provides low steering effort and good performance at all engine speeds Fully adjustable steering angle limiter with mechanical stops - reduces tire scrubbing Wheel hubs rotate on large tapered roller bearings Non-adjustable tie rod ends provide maximum lifeDRIVE AXLE Rugged Kessler D81 drive axle features full-floating designBRAKES Oil cooled wet disc brake system Designed for load capacities up to 40,000 lbs. Axle loads up to 540 kN (121,400 lbs) Bolt circle diameter inches (425 mm) Park brakeOPERATOR AREA Ergonomically designed hydraulic controls and high/low range control lever are within easy reach Three steps and hand grips provide easy access to operator compartment Angled floor plate and pedals are positioned for operator comfort Telescopic, tilt steer column Supportive mechanical full-suspension seat adjusts 8 inches (200 mm) for operator comfort Several air suspension seat options are available Steel overhead guard frame provides maximum high-stacking visibility Operator Presence System (OPS)

10 With complete hydraulic lock out requires the operator to be in the normal operating position before any travel or movement of the mast, tilt, carriage, and attachment can be initiated and that the travel or movement of the mast, tilt, carriage, and attachment is locked out when the operator leaves the seat for more than 2-3 seconds Optional light groups aid visibility in low-lighted areas. Light kits featuring innovative high-performance LED and halogen technology are available Optional ComforCabII features: tinted, curved glass; circulation fan; heater & defroster; electric wiper and windshield washer front, rear, top; intermittent front wiper; door retainer; 3 speed fan; 12-volt auxiliary power source; dome light, with many additional options to enhance comfort and productivitySpecial attachments, equipment or accessories not listed above may be available through Applications Engineering for specific application Box 7006 Greenville, North Carolina27835-7006 Part No.