HabasitLINK® Plastic Modular Belts Accessories

1 HabasitLINK Plastic Modular liability, application considerationsIf the proper selection and application of habasit products are not recommended by an authorized habasit sales specialist, the selection and application of habasit products, including the related area of product safety, are the responsibility of the customer. All indications / information are recommendations and believed to be reliable, but no representations, guarantees, or warranties of any kind are made as to their accuracy or suitability for particular applications.

2 The data provided herein are based on laboratory work with small-scale test equipment, running at standard conditions, and do not necessarily match product performance in industrial use. New knowledge and experiences can lead to modifi cations and changes within a short time without prior notice. BECAUSE CONDITIONS OF USE ARE OUTSIDE OF habasit S AND ITS AFFILIATED COMPANIES CONTROL, WE CANNOT ASSUME ANY LIABILITY CONCERNING THE SUITABILITY AND PROCESS ABILITY OF THE PRODUCTS MENTIONED HEREIN. THIS ALSO APPLIES TO PROCESS RESULTS / OUTPUT / MANUFACTURING GOODS AS WELL AS TO POSSIBLE DEFECTS, DAMAGES, CONSEQUENTIAL DAMAGES, AND FURTHER-REACHING CONSEQUENCES.

3 ! WARNINGH abasit Belts and chains are made of various plastics that WILL BURN if exposed to sparks, incendiaries, open fl ame or excessive heat. NEVER expose Plastic Belts and chains to a potential source of ignition. Flames resulting from burning plastics may emit TOXIC SMOKE and gasses as well as cause SERIOUS INJURIES and PROPERTY DAMAGE. See the Fire Hazard Data Sheet for additional type of all Belts IP 2x (DIN EN 60259 / IEC 529) Exceptions (IP1x) : F51, F52, F53, F54, SP615, IS615, SP620, IS620, PR620, PR620 SPS, PR 620 TTR, PR620 SPS CT, M2586, M3892, M5290, for series M1200 4 5 Accessories for series M2500 6 14 Accessories for series M3800 15 19 Accessories for series M5000 20 27 Accessories for series M5200 28 27 Accessories for series M6300 28 Accessories for series M6400 Accessories 1/2" pitch beltingFlights and side guards M1200 HabasitLINK Modular Belts are available with flights to convey products on inclined conveyors.

4 The flight modules are injection-molded one-piece designs that, when assembled, become an integral part of the belt . Flight modules are designed with ribs on one or both sides (no-cling) for improved release of wet or sticky food products and can also be cut to nonstandard heights. The flights fit all series M1200 Belts except M1230, side guards fit to M1220 (H1")Indents (E)The flight indent E is the distance between the edge of the belt and the edge of the flight. It is required for adequate support of the belt on its return way and hold-down during back bending applications (elevators).

5 On short conveyors or with special support structure, the flights may also be applied over the full belt width (E = 0). ( ")wear sidereturn waywear stripbeltM1220F05 M1234F05 M1220G05 Flight straightribs on one sideFlight straightribs on both sidesSideguardsCodeM1220F05M1234F05M1220 G05height Hlenght LHLHL Hmminch50215065021004502 Notch (N)The notch N is a gap in each row of flights, longitudinally aligned to allow the support of Belts wider than 600 mm (24") on their return way or in back bending applications.

6 The notch width (N) and the distance (M) from the belt edge is a multiple of the link increment mm ( "). For M1200 series the minimum notch width is mm ( ").Installation of flights and side guards; indentsThe side guards have a pitch of mm (1"), that is twice the module pitch. Therefore only one link per module needs to be cut for the side guard installation. This special solution provides higher strength. The smallest applicable sprocket size is M12S15 (15 teeth). The distance E1 between the flight end and the hold-down and support-shoes/wear strips should not be smaller than 5 mm ( ").

7 ( ) (1 ) Accessories 1/2" pitch beltingFlights and side guards M1200M1220G05/F05 Double pitch side guard, fi xed every second module rowPossible flight indents EFlight onlyFlight + side guardwith gap (G ~8 mm ( )Flight + side guardwithout gap (G ~2 mm ( )EEFEF mminchmminchmminchmminchmminchFlight over full belt width00 Module cutting , no module cutting cutting , no module Accessories 1" pitch beltingFlights, side guards and scoops M2500 (straight Belts )HabasitLINK Modular Belts are available with flights to convey products on inclined conveyors.))

8 The flight modules are injection-molded one-piece designs that, when assembled, become an integral part of the belt . Flight modules are available with ribs on one side (no-cling) for improved release of wet or sticky food products and can also be cut to nonstandard (1") (1") (1") (1")L25 (1")Flat Top flights straightopen hinge (USDA)Nub Top flights straightopen hinge (USDA)Flat Top flights straightclosed hingeFlat Top flights bent (Scoop)open hinge (USDA)Flush Grid flight corrugatedopen hinge (USDA)Side guardsCode flight side guardM2510 Fxx*1)M2514F052)M2520 Fxx*1)M2510B073)M2533F073) M253JF073)

9 M2520 Gxx*M252 RGxx*M252 LGxx*Applicablefor belt typeM2510, M2511M2516M2510, M2511M2514M2520/27M2533M2510, M2511M2516M2533 All 1" beltsexcept M2531height Hlength Lheight Hlength Lheight Hlength Lheight Hlength Lheight Hlength Lheight Hmminch251100475310042511004 281 mminch5021004 5021004 532 mminch7531004 753100475315067531004 783mminch 10041004 1034mminch 10041506 *Code xx = height of flight: 25 mm = 02 50 mm = 05 75 mm = 07 100 mm = 101) ribs on one side 2) ribs on both sides 3) without ribsM2520 Fxx smooth sideM2520 Fxx"no-cling" side (ribs)M2510 Fxx open hinge; "no-cling" sideM253JF07, open hinge.

10 Indent flight, corrugatedM2510B07, scoopopen hingeM2520G05M252RG/FG10 HHL26 ( ") (1 ) (1 ) (1 ) (1 ) Accessories 1" pitch beltingFlights and side guards M2500 (straight Belts )Indents (E)The flight indent E is the distance between the edge of the belt and the edge of the flight, and F is the distance between belt edge and side guard. It is required for adequate support of the belt on its return way and hold-down during back bending applications (elevators). On short conveyors or with special support structure, the flights may also be applied over the full belt width (E = 0).