HALO Commercial - Cooper Industries

1 halo Commercial d esc r iption Catalog # Type Recessed 8 inch aperture open downlight for two horizontal 26W. double twin tube or 26/32/42W triple twin tube compact fluorescent Project lamps. Fixture is suitable for Commercial construction. Insulation must be kept 3" from top and sides of housing. Universal input Date Comments electronic ballast with dimming and emergency options. Prepared by S P E C I F I C A T I O N feat u r es M ec h anica l conduit runs. Listed for (12) designated reflectors only, Frame #12 AWG (six in, six out) 90 C ordered separately. Application Boat shaped galvanized steel conductors and feed thru branch Note: IEM operates one lamp frame with a pre-set 1/2" plaster wiring. only in emergency mode. lip collar that adjusts from 1/2".

2 Lamp Socket Emergency Battery Pack - Average to 2" to accommodate ceilings 4-pin G24q base accepts (2) 26W Lamp Lumen Ratings up to 2" thick. May be used for DTT or 26/32/42W TTT lamps. new construction or remodeling REM option: (1) 26W 425lm, (1). installations. Provided with (2) Socket Housing 32W 600lm, (1) 42W 750lm remodel clips to secure frame Galvanized steel socket housing IEM option: (1) 26W 810lm, (1). when installed from below the attached securely to reflector 32W 910lm, (1) 42W 1040lm ceiling. with captive thumbscrew. Vents Mounting Brackets provide effective lamp thermal (Note: REM and IEM options PD8H242. management. operate one lamp only in Bar hanger receivers adjust 2" emergency mode. Average lamp 82H. vertically from above the ceiling Control Gear lumens are based upon REM.)

3 Or thru the aperture. Use with Universal 120V - 277V UNV or and IEM manufacturer ratings. No Fuss bar hangers or with 347V input electronic ballast for (2) 26W DTT. Delivered lumens depend upon 1/2" EMT. Removable to facilitate 26/32/42W compact fluorescent trim; refer to trim photometry to (2) 26/32/42W TTT. installation from below the lamps. factor delivered lumens). ceiling. Emergency Battery Pack Code Compliance No Fuss Bar Hangers REM Remote emergency Compact Fluorescent - Thermally protected and cULus Pre-installed and centered bar test switch. Housing includes listed for damp locations. hanger locks to tee grid with a 120V/277V, 60Hz dual-tap battery screwdriver or pliers. Centering pack provides 90 minutes of - IP20 rated for open trims.

4 8-Inch Aperture marks on the bar hanger emergency illumination. Long life - NFPA Life Safety (Emergency mechanism allows consistent maintenance free sealed nickel Open Downlight Battery Pack). positioning of fixtures. cadmium batteries recharge fully in 24 hours. REM configuration - EMI/RFI per FCC Title 47 CFR, O ptica l Part 18, non consumer limits New Construction or includes prewired and attached Reflector remote test switch plate and - Peel down wattage label Remodel Highly efficient one piece indicator light. REM option from 42W to 32W and 26W. aluminum reflector provides Non-IC. is the standard emergency Allows de-rating to set max. for equal lamp and lamp image configuration, and is compatible relamp wattage per project cutoff for a visually comfortable with all standard reflector specifications (multi-wattage optic.)

5 Optional cross blade louver options, ordered separately. housings only). provides sharper cutoff to lamp. Application Note: REM operates Self flanged standard. - DR - De-rated label housings are one lamp only in emergency - Specular Reflectors - Polished wattage specific for 32W or 26W. mode. flange standard with white painted flange option. IEM Integral emergency - High efficacy luminaire may be - Baffles and White Reflector - test switch. Housing includes used to meet IECC, ASHRAE, White painted flange 120V/277V, 60Hz dual-tap battery and Title 24 Commercial standard. pack provides 90 minutes of standards. emergency illumination. Long life Trim Retention maintenance free sealed nickel Reflector is retained with two cadmium batteries recharge fully torsion springs and held tightly to in 24 hours.

6 IEM configuration the finished ceiling surface. includes a prewired integral E l ect r ica l emergency test switch and Junction Box indicator light that are both (4) 1/2" and (2) 3/4" trade size pry accessible inside the reflector. outs positioned to allow straight The IEM option requires EM . ADV111713. January 10, 2013 9:24 AM. halo Commercial PD8H242. 82H. DIMENSIONS. ". [ mm]. " [ ]. ". [ ]. " [ ]. ". [ ]. ". [ ]. ". [ ]. E N E R G Y D ATA. PD8H242E, PD8 CPH242E PD8H2423E. Min. Starting Temp -5 F / -20 C Sound Rating Class A Min. Starting Temp 0 F / -18 C Sound Rating Class A. EMI/RFI Emissions FCC 47 CFR Part 18 Non-Consumer Limits EMI/RFI Emissions FCC 47 CFR Part 18 Non-Consumer Limits Input Frequency 50/60 Hz Power Factor > Input Frequency 50-60Hz Power Factor > THD < 10% Input Voltage 120V - 277V 10% THD < 10% Input Voltage 347 VAC 10%.

7 Crest factor < Crest factor < Operating Frequency > 40kHz UL Listed Class P, Type 1 Outdoor, CSA or C/UL Certified Operating Frequency 50-60 kHz cULus Certified Input Power 54W Input Power 44W. Input Current @ 120V (2) CFQ26W/G24q Input Current @ 347V. (2) CFQ26W/G24Q. Input Current @ 277V Ballast factor Ballast factor Input Power 44W. Input Power 54W (2) CFTR26W/GX24Q Input Current @ 347V. Input Current @ 120V Ballast factor (2) CFTR26W/GX24Q. Input Current @ 277V Input Power 62W. (2) CFTR32W/GX24q Ballast factor Input Current @ 347V. Input Power 69W Ballast factor Input Current @ 120V Input Power 80W. (2) CFTR32W/GX24Q. Input Current @ 277V (2) CFTR42W/GX24q Input Current @ 347V. Ballast factor Ballast factor Input Power 94W. Input Current @ 120V.

8 (2) CFTR42W/GX24Q. Input Current @ 277V. Ballast factor halo Commercial PD8H242. 82H. O r d e r ing info r mation SAMPLE NUMBER: PD8H242E 82HC. O r d e r h o u s i n g , r e fl e c t o r a n d l a m p s e p a r a t e l y f o r a c o m p l e t e l u m i n a i r e . Housing Reflector Finish Option Accessories Mult-Wattage 82H = 8 horizontal C=Specular Clear HB128 APK = L channel hanger PD8H242 = 8 Inch horizontal (2) 26/32/42W DTT/TTT CFL 82 HEM = 8 Horizontal, G=Specular Gold bar, 26 , No-Fuss', PD8 CPH242 = 8 Inch horizontal (2) 26/32/42W Emergency (required H=Semi Specular Clear pair (replacement). DTT/TTT CFL, CCEA listed (Chicago Plenum) with IEM ballast option) W=White (White Flange) RMB22 = 22 long wood joist Note: Multi-wattage dimming options limited to BB=Black Baffle (White Flange) mounting bars 32/42W DTT/TTT Shielding Media WB=White Baffle (White Flange).

9 [Blank] = none De-Rated Label CB = Cross blade louvers PD8H226 = 8 Inch horizontal (2) 26W DTT/TTT CFL. (blade finish matches reflector, Flange Option PD8 CPH226 = 8 Inch horizontal (2) 26W DTT/TTT. not available with baffle) Blank=Polished Flange (C, G, H). CFL, CCEA listed (Chicago Plenum). PD8H232 = 8 Inch horizontal (2) 32W TTT CFL Blank=White flange (W, BB, WB). PD8 CPH232 = 8 Inch horizontal (2) 32W TTT WF=White Flange (C, G, H). CFL, CCEA listed (Chicago Plenum). Ballast Option Multi-Wattage E = 120V-277V 50/60Hz UNV. IEM = 120V-277V 60Hz dual-tap emergency battery ballast with integral test switch thru reflector, requires EM reflector optin, ordered separately REM = 120V-277V 60Hz dual-tap emergency battery ballast with remote test switch plate 3E = 347V, 50/60Hz 1 DMARKX = 5% two-wire (32/42W TTT) dimming, 120V.

10 2 DMARKX = 5% two-wire (32/42W TTT) dimming, 277V. EDMARK7 = 5% 0-10V (32/42W TTT) dimming, 120-277V. 1 DMARKXIEM = 5% two-wire (32/42W TTT) dimming, 120V, with IEM emergency option 2 DMARKXIEM = 5% two-wire (32/42W TTT) dimming, 277V, with IEM emergency option EDMARK7 IEM = 5% 0-10V (32/42W TTT) dimming, 120-277V, with IEM emergency option 1 DMARKXREM = 5% two-wire (32/42W TTT) dimming, 120V, with REM emergency option 2 DMARKXREM = 5% two-wire (32/42W TTT) dimming, 277V, with REM emergency option EDMARK7 REM = 5% 0-10V (32/42W TTT) dimming, 120-277V, with REM emergency option De-Rated Label E = 120V-277V 50/60Hz UNV. IEM = 120V-277V 60Hz dual-tap emergency battery ballast with integral test switch thru reflector, requires EM reflector optin, ordered separately REM = 120V-277V 60Hz dual-tap emergency battery ballast with remote test switch plate 3E = 347V, 50/60Hz 1 DMARKX = 5% two-wire (26W or 32W DTT/TTT ) dimming, 120V.