1 HALO. DESCRIPTION. Catalog # Type Recessed 3- inch square aperture LED downlight / directional with field interchangeable optics provide various distribution patterns. Ideal for accent, task and general area lighting. Housing is airtight, suitable for 2x6 Project residential or shallow plenum commercial constructions and can be used in direct contact with insulation. Trims are available in a range of finishes Date Comments and can be installed rimless with an optional rimless adapter. Use where high efficiency, excellent light control and low aperture brightness are required.
2 Prepared by SPECIFICATION FEATURES. Frame LED Module Junction Box Galvanized steel plaster frame with LED array is field replaceable Galvanized steel junction box with integral bar hanger receivers Proximity phosphors over chip 18in3 internal volume Setscrew provide positive horizontal on board LEDs provide a uniform Listed for (12) #12 AWG 90 C splice locking source with high efficiency and no conductors Collar adjusts vertically to pixilation (7) 1/2 conduit pry-outs positioned accommodate 1/2 to 7/8 thick Color accuracy within 3 SDCM and to allow straight conduit runs ceilings and locks in position with 90 CRI minimum (3) Slide-N-Side non-metallic (NM).
3 (4) screws Passive cooling achieves L70 at wire traps Use optional collar extender for 7/8 50,000 hours Accepts 14-2, 14-3, 12-2, 12-3 to 1-1/4 thick ceilings and 14-2, 14-3, 12-2 Canadian NM. Integral gun sights facilitate the use Primary Optic cable of guide strings or laser lines Precision molded TIR optics deliver (3) 4-port push wire nuts mains highly efficient and uniform patterns Shipped with overspray protector Various patterns are available and voltage connections HL36SA . installed can be interchanged without tools Compliance TL3.
4 Housing Type IC inherently protected, Steel housing painted matte black Media suitable for direct contact to air for a visually dark interior Integral media holder accepts up to permeable insulation and cULus Removable top allows service from (2) 2 diameter thick color listed for damp locations above filters or lens Not for use in direct contact with 3 Square Order color filters and lens spray foam insulation, consult Bar Hangers separately NEMA LSD57-2013 Aperture LED. GOT NAIL! Gen 3 bar hangers Wet location listed in covered adjust from 10-1/2 to 24 wide Trims ceilings.
5 Housing is IP20 certified Captive nail penetrates standard and Die cast aluminum trims are and when installed with a lens trim Shallow New engineered lumber available in open, lens and lens wall IP55 certified below the ceiling in Construction Mounting flange levels platform with wash styles covered ceiling applications only Downlight / Directional Polymer non-conductive trim meets ceiling Airtight per ASTM-E283-04 Housing and Trims many local code requirements for Integral clip attaches directly to Suitable for use in clothes closets dead front'.
6 Tee-bar when installed in accordance IC & Airtight Physical and optical cutoff provides with the NEC spacing Gaskets visual comfort requirements Gaskets achieve restrictive airflow Light trap eliminates spill light with EMI/RFI emissions per FCC 47 CFR Up to 1800 lm requirements without additional flange Part 15 consumer limits caulking Multiple finishes to match many Contains no mercury or lead and d cors RoHS compliant Adjustment Mechanism Available in self-flanged or rimless Rotates 365 , tilts 45 and locks Photometric testing in accordance styles with optional rimless adapter with IES LM-79-08.
7 In position maintaining any aiming angle Shielding Lumen maintenance projections in Angle markings assist in repeatable Micro-prismatic lens standard with accordance with IES LM-80-08 and TM-21-11. settings lens trims Translating center beam optics Hinged to allow rimless trim removal Can be used for State of California Title 24 high efficacy LED. aligns axis of primary reflector with Driver compliance under JA8, reference aperture from nadir to 45 . Field replaceable constant current Modernized Appliance Efficiency Trim Retention Database System (MAEDBS) for driver provides noise free operation Attached by (8) rare earth 2016 JA8 High Efficacy Lighting UNV 120-277 VAC 50/60Hz input Neodymium magnets, holds trim ENERGY STAR certified, reference Continuous, flicker-free 1%.
8 Securely to the ceiling certified light fixtures database dimming, available with LE and TE. Tether secures trim to housing phase cut (at 120V only) and 0-10V Warranty E N E R G Y DATA. during service or adjustment analog control Five year limited warranty, consult website for details. Input Voltage 120V 277V. Input Current (A) (A). Input Power (W) (W). Inrush (A) (A) (A). THD: 20%. PF: T Ambient -40 - +40 C. Sound Rating 22dba TD518345EN. 5/02/2019. HL36SA . TLS3. DIMENSIONS.. [ mm].. [ mm].. [ mm] [ mm].. [ mm].. [ mm] - 7/8 with standard collar 7/8 - 1-1/4 for extension collar accessory [ mm].
9 (ceiling cutout). 14 . [ mm] Note: For use in shallow ceilings with 2 x 6 joist construction. ORDERING INFORMATION. Models Wattage Distribution Light Engine Input / Control Housing Type Options HL36SA = 3 shallow 20 = 20W (nominal) SP = 15 beam 927 = 90 CRI, 2700K ED010 = UNV 120-277V ICAT= insulation RA3S = rimless adapter for HL36SA housings square new NFL = 25 beam 930 = 90 CRI, 3000K 50/60Hz leading or contact and airtight and trims construction FL = 40 beam 935 = 90 CRI, 3500K trailing edge phase cut CE3S = collar extender for HL36SA housings, directional housing WFL = 55 beam 940 = 90 CRI.
10 4000K 1% dimming at 120V adjusts from 7/8 to 1-1/4 thick ceilings only and UNV 120- TIR45SP15 = 15 beam 277V 50/60Hz 0-10V TIR45 NFL25 = 25 beam 1% dimming TIR45FL40 = 40 beam TIR45 WFL55 = 55 beam TIR45MH12PK = replacement media holder, package of 12. L100 Series = lens and filters, see spec sheet OTLS3MW = oversized trim ring for TLS3 trims Trim Shielding Finishes Flange TLS3 PIN = aperture square pinhole w/ [blank] = open Electroplated Finishes [blank] = full overlap self-flanged oculus, open, self-flanged BNBB = brushed nickel flange, black oculus ORBBB = oil rubbed bronze flange, black oculus Painted Finishes MWWB = matte white flange, white oculus MWBB = matte white flange, black oculus MBBB = matte black flange, black oculus TLS3 PIN = aperture square pinhole w/ [blank]