Hexalobular internal driving feature for bolts and screws

1 Reference numberISO 10664:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO10664 Second edition2005-07-01 Hexalobular internal driving feature for bolts and screws Empreinte six lobes internes pour vis Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP., W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --ISO 10664:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy.

2 The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.

3 ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail Web Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP., W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --ISO 10664:2005(E) ISO 2005 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

4 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

5 ISO 10664 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and replaces the first edition (ISO 10664:1999), which has been technically revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP., W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP., W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --INTERNATIONAL STANDARD ISO 10664:2005(E) ISO 2005 All rights reserved 1 Hexalobular internal driving feature for bolts and screws 1 Scope This International Standard specifies the shape and basic dimensions of the Hexalobular internal driving feature for bolts and screws , including the gauging method.

6 The curvature of the contour of the Hexalobular internal driving feature is defined by the gauges specified in Tables 3, 4 and 5. Additional information which can be used when drawing the contour is given in Annex A. The intent of this International Standard is to provide the details necessary for inspection of the Hexalobular driving feature . It is not suitable for, nor intended to be used as, a manufacturing standard. 2 Basic dimensions See Figure 1 and Table 1. Counterbore: c u 0,13 mm up to socket No. 15 c u 0,25 mm over socket No. 15 Penetration depth t: see relevant product standard. NOTE The contour of the bottom of the socket beyond the gauge is at the option of the manufacturer. a See Table 2. Figure 1 Basic dimensions Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP.

7 , W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --ISO 10664:2005(E) 2 ISO 2005 All rights reserved Table 1 Basic dimensions Dimensions in millimetres Nominal dimensions a Hexalobular socket No. A B 6 1,75 1,27 8 2,4 1,75 10 2,8 2,05 15 3,35 2,4 20 3,95 2.

8 85 25 4,5 3,25 30 5,6 4,05 40 6,75 4,85 45 7,93 5,64 50 8,95 6,45 55 11,35 8,05 60 13,45 9,6 70 15,7 11,2 80 17,75 12.

9 8 90 20,2 14,4 100 22,4 16 a The curvature of the contour of the Hexalobular internal driving feature is defined by the gauges specified in Tables 3, 4 and 5. 3 Gauging Principle The Hexalobular internal driving feature shall allow the GO gauge (see ) to enter freely to the penetration depth t, as specified in the relevant product standards. The NO GO gauges (see and ) shall not enter the Hexalobular internal driving feature to a depth greater than the fallaway allowance specified in Table 2.

10 Table 2 Fallaway allowance Dimensions in millimetres Socket No. 6 8 10 15 20 25 30 40 45 50 55 60 70 80 90 100 Fallaway allowance, f 0,35 0,48 0,56 0,67 0,79 0,90 1,12 1,18 1,39 1,56 1,98 2,35 2,75 3,11 3,53 3,92 All gauging is performed with reference to the top surface of the head. In the case of oval or round top heads, measurements are taken from the actual intersection of the top surface of the head and the Hexalobular internal driving feature counterbore. Copyright International Organization for Standardization Provided by IHS under license with ISO Sold to:UNIVERSAL PUNCH CORP., W0434214 Not for Resale,2007/8/8 17:6:15 GMTNo reproduction or networking permitted without license from IHS--``,`,`,,,,,,,`,,``,-`-`,,`,,`,`,,`- --ISO 10664:2005(E) ISO 2005 All rights reserved 3 When using a dial penetration gauge, this should be adjusted to zero while the gauge is pressed against a flat surface, thereby compressing the plunger to make it flush with the gauge reference surface, see Figure 2.