HY-LUX ENAMEL - Ellis Paint

1 PProductProfileProductProfileSSHHEEEETTP lease refer to label for cautions and warnings pertaining to this Number:Colors:Viscosity:Solids by Weight:Solids by (Volatile Organic Compounds): *Solvent(s) Used:Finish:Flash Point:Dry-To-Touch @ 77 F:Dry-To-Handle @ 77 F:Recoat time @ 77 F:Coverage (Theoretical):TECHNICAL DATA3100 SeriesClear, Assorted Colors and Tint Bases95 - 105 Kreb Units @ 77 F50% - 71%47% - 59%340 grams per liter or less ( lbs/gal)Aliphatic Hydrocarbons/Aromatic Hydrocarbons/Esters/PCBTFE xtremely High Gloss 80+76 F/TCC 4 - 6 hours16 hours1/2 - 2 hours758 - 957 square feet per gallon @ 1 mil DFT HY-LUX ENAMELD escription: HY-LUX ENAMEL is a durable, extremely high-glossenamel made from a premium quality, acrylic-modified,alkyd resin.

2 Formulated to give long-term weatherprotection and a colorful appearance. HY-LUX ENAMELis tough and gives exceptional performance on a widevariety of metal substrates. It is available in clear and awide selection of colors and tint bases. Designed forapplication by brush, roller or : Extremely high gloss Tough and durable A true, general purpose ENAMEL Excellent hide and coverage Easily applied using conventional methods and equipment Stocked in well-known industrial colorsCompatible Primers: Ellis 600, 1200, 4400 & 7900 SeriesHY-LUX ENAMEL Directions for use:SURFACE PREPARATIONGENERAL:All surfaces to be painted must be clean, dryand in fit condition to be painted.

3 Be sure to remove allwax, silicone, powdery or scaling rust, loose or peelingpaint and all other foreign matter. Smooth, slick surfacesshould be sanded to give a mechanical tooth to promoteadhesion. Prime bare and uncoated surfaces with one ofthe following Ellis Primers: 600 Solventborne Series,1200 Waterborne Series, Maximus 4400 Series orMaximus 7900 Series FERROUS METAL:Clean off all dirt, grease oil,wax or other foreign matter. All loose, powdery or scalingrust must also be removed. A completely de-rustedsurface is recommended. Prime with Ellis Primer. NON-FERROUS METALS:Clean the surface a prep coat of HY-LUX 690 Low VOC Etching Filleras a first coat over the non-ferrous metal to etch thesurface and promote adhesion.

4 Allow 30 minutes to dryand follow with a coat of Ellis Primer within 8 8 hours, the HY-LUX 690 Low VOC Etching Fillershould be lightly sanded before applying the first coat ofEllis SURFACES:Be sure all loose and peelingpaint is completely removed, and the surface is excess chalkiness with a wire brush or bysanding. Feather edge and spot prime with Ellis :Mix thoroughly before use and/or after POLYURETHANE CATALYST:For increasedperformance, 8499 Polyurethane Catalyst may be addedto HY-LUX 3100 Series ENAMEL . Refer to the 8499 Polyurethane Catalyst label for directions andprecautions regarding applying products SCHEDULE WITH 8499 POLYURETHANECATALYST:Dry times are based on recommended dryfilm thickness of - mils.

5 Thicker films willextend dry times. Air dry times at 77 F and 50% - Dust-free, 1 - 2 hours, Tack-free 4 - 6 hours,Tape-free, 24 hours, Force dry time at 120 F - 40 minutesTHINNING:DO NOT EXCEED LOCAL VOC REQUIREMENTS. Inregulated areas, use Ellis 80/20 Zero VOC Exempt Spraying:Thin to spray viscosityFor Brushing or Rolling: Thin : Two coats are recommended. To avoidwrinkling, the second coat must be applied in 30 minutes to 2hours, or after a minimum of one week from the time ofapplying the first coat. DRY TIME (@77 F):DUST-FREE: 4 - 6 hours, DRY TOHANDLE 16 hours, RECOAT: 30 minutes to 2 hours, or after aminimum of one week, FULL CURE: 7 :Equipment should be thoroughly cleanedimmediately after use in an enclosed spray equipmentcleaner with Ellis 80/20 Zero VOC Exempt LIFE:Shelf life is 2 years from date of manufacturewhen stored at temperatures not to exceed 90 F.

6 * Rule and Regulation requirements are mandated bylocal air management districts and change from district todistrict. Refer to your local Rules and Regulations fromyour air resources board or on the web to product label and Material Safety Data Sheet(MSDS) for cautions and warnings pertaining to this Warranty: Ellis Paint Company certifies that all Ellis coatings delivered to the customer innew, sealed containers will meet all pertinent quality standards presented inEllis published literature. Since matters of surface preparation, applicationprocedures and other local factors which affect performance are beyond itscontrol, Ellis assumes no liability for coating failure other than to supplyreplacement material for Ellis coatings shown to be defective.

7 If you havequestions, contact your dealer, visit , or call Ellis PaintCompany. There is no other warranty, either expressed or East Pico Boulevard, Los Angeles, CA 90023, Ph: (323) 261 8114, Fax: (323) 780 9940.