Example: barber

HYDRAULIC COUPLING IDENTIFICATION CHART

HYDRAULIC COUPLING IDENTIFICATION CHARTM ated angle seat with O-ringThis type of seal is found on BSP and DIN terminations. It uses both the O-ring and the mated angle to make the O-Ring LocationB. Nose SeatC. Seat AngleD. COUPLING TerminationInsideInverted60 InclusiveInsideInverted24 InclusiveBritish Standard Pipe ParallelThread 30 Thread O-ringMale (MBSPP)Female (FBSPORX)DIN 24 coneTube Thread Thread (MDL/MDH)Female (FDLORX/FDHORX)Dash SizeNominal Size (ins)No. Threads per InchMale Thread (mm)MBSPPF emale Thread (mm) FBSPORX-41/4 Thread sizeTube Light SeriesTube Heavy SeriesMale Thread (mm)MDL/MDHF emale Thread (mm) FDLORX/FDHORXM12 X X X X X X X X X X X X X face sealThis type of seal is found on O-ring

HYDRAULIC COUPLING IDENTIFICATION CHART Mated angle seat with O-ring This type of seal is found on BSP and DIN terminations. It uses both the O-ring

Tags:

  Chart, Identification, Hydraulic, Coupling, Hydraulic coupling identification chart

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of HYDRAULIC COUPLING IDENTIFICATION CHART

1 HYDRAULIC COUPLING IDENTIFICATION CHARTM ated angle seat with O-ringThis type of seal is found on BSP and DIN terminations. It uses both the O-ring and the mated angle to make the O-Ring LocationB. Nose SeatC. Seat AngleD. COUPLING TerminationInsideInverted60 InclusiveInsideInverted24 InclusiveBritish Standard Pipe ParallelThread 30 Thread O-ringMale (MBSPP)Female (FBSPORX)DIN 24 coneTube Thread Thread (MDL/MDH)Female (FDLORX/FDHORX)Dash SizeNominal Size (ins)No. Threads per InchMale Thread (mm)MBSPPF emale Thread (mm) FBSPORX-41/4 Thread sizeTube Light SeriesTube Heavy SeriesMale Thread (mm)MDL/MDHF emale Thread (mm) FDLORX/FDHORXM12 X X X X X X X X X X X X X face sealThis type of seal is found on O-ring boss, flat-face O-ring, British flat-face O-ring and O-ring flange couplings.

2 O-ring boss couplings have straight threads with the O-ring on the outside of the threads next to the large hex nut. Generally the O-ring will not be present on a used COUPLING but the groove for the O-ring will be and British flat-face O-ring couplings have straight threads. The female has a flat face; the male has a flat face with a groove to accept the O-ring. Differ-ences between flat-face and British flat-face are deter-mined when measuring thread flange couplings have no threads but do have a flat face with a groove to accept the O-ring.

3 The connection is made with two flange half boots that go over the O-ring flange and are bolted to the O-Ring LocationB. Nose SeatC. Seat AngleD. COUPLING TerminationO-ring located in flange grooveflat faceO-ring located outsideflat faceO-ring located at nose seatflat faceDash SizeNominal Size Flange (mm)Flange Head Thickness (mm) E A (mm) B (mm) C (mm)Code 61 - FL-81/2 joint or mated angleThis type of seal is found on National Pipe Straight Mechanical (NPSM), British Standard Pipe Parallel (BSPP), JIC, SAE, JIS, Komatsu, DIN, North American Stand Pipe, Metric Stand Pipe, Inverted Flare and Kobelco.

4 Different angles are used to create the seal, but the angles are cut two different ways, Standard and seat couplings have the nose angle of the male on the outer surface of the cou-pling. These couplings are: JIC, SAE, JIS, seat couplings con-tain the nose angle of the male on the inside bore of the COUPLING . These couplings are: (NPSM) National Pipe Straight Mechanical, (BSPP) British Standard Pipe Parallel, DIN, North American Stand Pipe, Metric Stand Pipe, Inverted Flare and interfaceThis type of seal is found on the (NPTF) National Pipe Tapered for Fuel or the (BSPT) British Standard Pipe Taper.

5 Characteristics of this thread is the male has a smaller di-ameter at the end, tapering to a larger diameter at the hexagon. When the male is screwed into the fe-male the thread deforms, thus creating the seat anglesUsing the seat gauge, determine the angle of the seat, as illustrated. When the centreline of the seat gauge extends parallel with the projected longitudinal axis of the COUPLING , then the angles of the gauge and seat the measurements taken to a COUPLING shown in the tables above that appear to be : Thread binding will occur when different thread configurations are NOT mix thread thread IDENTIFICATION kits containing reference charts, vernier, seat gauges and thread gauges are available.

6 Order reference: are parallelCentrelines at an angleCentrelines are parallelMALE(Outside diameter)FEMALE(Inside diameter)RightWrongMeasuring threadsWith the calliper measure the thread diameter of the largest point. (Outside diameter ( ) of male threads. Inside diameter ( ) of female threads.)Using the thread gauge, determine the number of threads per inch. Comparison of gauge and COUPLING threads against a lighted background will ensure an accurate O-ring O-ring bossO-ring face sealThread (MB)Thread (FB)Thread (MFFOR)Thread Swivel (FFORX)ACBF lange (mm)Flange Head Thickness A (mm) B (mm) C (mm)Flange (mm)Flange Head Thickness A (mm) B (mm) C (mm)Code 62 - FLHCode 62 - SizeNominal Size (ins)No.

7 Threads per InchMale Thread (mm) MBFemale Thread (mm) FB O-Ring (mm)-21/8 247, 249, SizeNominal Size (ins)No. Threads per InchMale Thread (mm) MFFORF emale Thread (mm) FFORX-41/4 ,0-161 O-Ring LocationB. Nose SeatC. Seat AngleD. COUPLING TerminationNoneStandard37 NoneStandard45 NoneStandard30 NoneInvertedNoneInverted30 NoneInverted45 None, Except -20 Inverted24 InclusiveNoneStandard24 InclusiveJIC 37 FlareSAE 45 FlareJapanese Industrial Standard & KomatsuMetric Stand PipeNational Pipe Inverted FlareFrench Gaz 24 coneFrench Gaz 24 high pressure flangeThread 37 Thread 45 Thread 30 Thread Thread 30 30 Thread 42 Thread (MJ)Female Swivel (FJX)Male (MS)Female Swivel (FSX)Male (MJIS or MK)Female (FJISX or FKX)Solid Male (MFA)

8 NutStand Pipe FittingBite SleeveMale (MP)Female (FPX)Male (MIX)Female (FI)Male (MFG)Female (FFGX)Male (MPFL)Female (FPFL)XXD. COUPLING TerminationNational Pipe TaperedBritish Standard Pipe TaperedThread Thread Solid Male (MP)NPTF or NPSP Solid Female (FP)55 Thread (MBSPT)60 Dash SizeNominal Size No. Threads per InchMale Thread (mm)MPFemale Thread (mm) FP-21/8 ,1-41/4 SizeNominal Size No. Threads per InchMale Thread (mm) MBSPT-21/8 SizeNominal Size No. Threads per InchMale Thread (mm)MJFemale Thread (mm) FJ X-41/4 SizeNominal Size No.

9 Threads per InchMale Thread (mm) MSFemale Thread (mm) FSX-41/4 SizeNominal SizeNo. Threads per InchMale Thread (mm)MJISF emale Thread (mm) FJISXN ominal Size (mm)Metric Thread SizeMale Thread (mm)MKFemale Thread (mm) FKX-41/4 , Stand Pipe DIN Tube (mm)MSPM etric Nut Thread - LightMetric Nut Thread - x x x x x x x x x x x x x x x x x x SizeNominal Size (Ins) No. Threads per InchMale Thread (mm)MPFemale Thread (mm) FPX-21/8 ,1-41/4 SizeNominal Size (Ins)No.

10 Threads per InchMale Thread (mm)MIXF emale Thread (mm) FI-21/8 287, 249, SizeNominal Size (Ins) Metric Thread SizeMale Thread (mm)MFGF emale Thread (mm) FFGX-41/4 SizeNominal Size (Ins) X Dia (mm) MPFL X Dia (mm) FPFL-81/2 headThread July 2015 GATES AUSTRALIA PT Y LTD 1-15 Hydrive Close, Dandenong South, Victoria, 3175 PH: +61 3 9797 9666 FA X: +61 3 9797 9600


Related search queries