HYDRAULIC LINER INSTRUCTIONS - swopparts.com

1 _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 SWTM2700 HYDRAULIC LINER PULLER: OPERATION & MAINTENANCE *SAFETY NOTE: As with all HYDRAULIC equipment, appropriate safety gear should be utilized when operating this LINER puller tool this includes (but may not be limited to) safety glasses, steel-toed shoes, and gloves. Caution should be used in the vicinity of the puller head and puller legs as gaps and sharp edges exist and may pinch or cut if handled improperly.

2 Caution should also be used around the H-block and piston pieces when the HYDRAULIC hand pump is being operated.** ASSEMBLY INSTRUCTIONS 1. Slip the pre-assembled H-block tubes (Fig. 2) into the H-block slots as shown in Fig. 3; tighten the plates down with the hex bolts just enough to keep the tubes from falling out while they are being installed. Fig s 2 & 3: pre-assembled tube and H-block with tubes installed on puller bolt 2. Remove the cylinder head from the pump but leave the cylinder head studs in place.

3 3. Retract the legs of the puller head. 4. Insert the tool puller head end first through the LINER bore. 5. Center the H-block tubes over two opposing cylinder head studs. _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 Fig. 4: installing the LINER puller assembly (shown on a duplex pump) 6. Tighten the tube set screws to hold the H-block assembly in place. 7. Push the puller stem in until it becomes apparent that the puller legs have pushed through the LINER and are engaging the end of the LINER and not its sides (see Fig.)

4 5 below). _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 Fig. 5: cut-away view of correct tool engagement inside of a duplex LINER (left); incorrect engagement (center and right) 8. Tighten the hex nut and re-tighten the tube plates if necessary. OPERATING INSTRUCTIONS 1. Connect the HYDRAULIC hand pump to the quick-coupler on the H-block. 2. Pressure up the hand pump until the LINER becomes loose enough to remove by hand.

5 NOTE: there is a mark on the piston to indicate when the stroke limit is being reached; DO NOT EXCEED this stroke limit. For operation and maintenance of the hand pump, see the separate manual included with the puller kit. _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 CONTENTS & DIMENSIONS Pictured are the parts that come with the SWTM2700 tool kit.

6 Overall dimensions are shown on the following pages. _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 H-block (Qty: 1) Puller Bolt (Qty: 1) _____ Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 (O): 713-675-7541 (F): 713-675-5206 Puller Head Assembly (Qty: 1) H-block Tube Assembly (Qty: 2) CHECKED BY10/02/2013 ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT DCAABCD1234567887654 THE WRITTEN PERMISSION OF SOUTHWEST OILFIELD 3 SOLE PROPERTY OF SOUTHWEST OILFIELD PRODUCTS.

7 21 SWTM2700N/ATHIRD ANGLE PROJECTIONTHE INFORMATION CONTAINED IN THIS DRAWING IS THE N/ABHJM06/30/2015 PRODUCTS IS TREATTITLE:SIZEBBHYDRAULIC LINER PULLERUNLESS OTHERWISE SPECIFIED:SHEET 1 OF 1 SOUTHWEST OILFIELD PRODUCTS10340 WALLISVILLE ROAD, HOUSTON,TX 77013 MATERIALBDRAWN BYDWG. ARE IN INCHESTOLERANCES:FRACTIONAL1/64 ANGULAR: DECIMAL +.005 / FILLETS & RADII - 1/16 MAX CHAMFERS 1/16 X 45 MAXSURFACE FINISH 125 RMS MAXCONCENTRICITY NOT TO SHARP CORNERS 1/32 X 45 MAXITEM BOLT12 SWTM1007 PULLER BOLT ADAPTOR13 SWTM1016 LOCKING BOLT14 SWTM1017 PULLER HEAD15 SWTM1012 DOWEL PIN26 SWTM1018 PULLER LEG27 SWTM1006-BH-BLOCK TUBE28 SWTM1006-AH-BLOCK LEG29 SWTM1019H-BLOCK PLATES21092865A7945/8-11 HEX BOLT211 HHN1500-61-1/2 - 6 HEAVY HEX NUT112N/A3/8-16 SET SCREW (.)

8 375" LONG)213N/A3/8-16 SET SCREW (1" LONG)214 SWTM1711 HYDRAULIC COUPLING115 SWTM10111/8" COTTER PIN116 SWTM1013 SNAP RING117 SWTM1015 WEDGE118 SWTM1707 HYDRAULIC HOSE119 SWTM1708 HYDRAULIC HAND PUMP120 SWTM2701H-BLOCK1181991011201097132121234 51415166617513781