HYDRAULIC MOTORS

1 L. H Y D R A U L IC M O T O R S. I N S T A L L A T I O N G U I D E. HYDRAULIC MOTORS poclain HYDRAULICS. FIXATIONS 9. Attachment to the Chassis 9. Attachments to the Shaft 10. Coupling by Splines 11. Shrink-Disk Coupling 12. Other Means of Connection 14. Hydrobasis checking 14. DRUM BRAKES 15. Technical information 49/93 15. Fluid 17. Drum 17. Bleeding a Drum Brake Cylinder 17. Adjusting the parking brake cable 19. Parking Brake (drum brakes) 20. Wearing In 20. BRAKE DEACTIVATION 21. Mechanical brake deactivation 22. HYDRAULIC brake deactivation 23.

2 Brake Release Pressure 24. 2 12/05/2015. poclain HYDRAULICS HYDRAULIC MOTORS CONTENT. Overview OVERVIEW 6. Component Identification 6. Delivery 6. Storage 7. Storage Interval 7. Paint 7. Products PRODUCTS 9. Accessories ACCESSORIES 25. Speed sensors TD, TR and T4 25. Shrink-Disk 30. Circuits CIRCUITS 33. Checking Connections 33. Rinsing the Circuit 35. Casing 36. Bleed the Casing 36. Brake bleed 37. Decontamination and Filtration 39. OILS 41. Oils Fluid Selection 41. Water content 45. STARTUP 47 Startup Tightening torques TIGHTENING TORQUES 50.

3 Diagnostic DIAGNOSTIC 52. Anomalies at 0 kilometers 52. 12/05/2015 3. HYDRAULIC MOTORS poclain HYDRAULICS. Foreword: This document is intended for installers of poclain Hydraulics' products. It describes the technical properties of poclain Hydraulics products and specifies their conditions for installation and startup that will assure their optimal operation. This document includes important remarks concerning safety. They are displayed in the following manner: Safety notice. This document also includes instructions essential for the operation of this product along with general information.

4 They are displayed in the following manner: Essential instruction. General information. Recover used oil. 4 12/05/2015. poclain HYDRAULICS HYDRAULIC MOTORS Warnings Before Installation Take all necessary safety precautions (people and machines) and comply with safety regulations in effect. Overview Confirm that mobile equipment is immobilized. Confirm that the HYDRAULIC systems' energy generator ( motor ) is stopped and electric power is disconnected. Products Lay out a safety perimeter. Accessories Do not perform work on a HYDRAULIC system that is hot or under pressure (discharge the accumulators).

5 Oil that is hot or under pressure can cause serious burns and infection. Consult a physician in case of accident. During Installation Install the HYDRAULIC system according to the specifications and processes appearing in this document. Circuits Support the components using a lifting device whose capacity is adequate for attaching the components to the chassis. During handling protect all sensitive surfaces from shocks (centerings, bolts, connectors, plugs, etc.). Oils Confirm that the components' centering and support surfaces on the chassis are clean (free of paint).

6 Never heat HYDRAULIC fluid which can ignite at high temperature. Some solvents are also inflammable. Startup Do not smoke while working on the system. Tightening After Installation torques Consult repair documents for system and component maintenance and repair instructions. Do not over-size the safety valves. Diagnostic Wearing in the MOTORS is not necessary; full performance is reached after a few hours of operation. 12/05/2015 5. HYDRAULIC MOTORS poclain HYDRAULICS. OVERVIEW. Component Identification Older type Present type Product MS05-0-D24-F04-1220-0000 A.

7 Identification plate 000743806K B. 000 63622 C. D. A Model code ex. MS05-0-D24-F04-1220-0000 MS08-D-EE5-F08-1K24-2 DEJM. B Part number ex. 000743806K A52424H. C Serial number ex. 002-63622 VFR8008687001. Primer Topcoat Primer Topcoat J K J K. N H N FN. G G H. J1. D Primer / topcoat FJ. B. CN. FV. FG. The item code and sequence number must appear on each spare parts order. Delivery The MOTORS are delivered: In boxes. Without oil. Painted with primer. With protected openings (Plastic/metallic plugs or plates with joints for the flanges, sealing them).

8 With protected attachment surfaces (these surfaces are never painted), they are covered with a thin film of varnish to limit any oxidation. If the plugs are to remain in place while the motor is operating, the plastic plugs must be replaced by metal ones. 6 12/05/2015. poclain HYDRAULICS HYDRAULIC MOTORS Storage The MOTORS are delivered in boxes. If they must be stored, leave them in the boxes. If this is not possible, follow the recommendations below in order to avoid damage to sensitive parts. Wheel motor Shaft motor On shaft On attachments Overview Products Bolts protected by nuts anchored to the head of the bolt.

9 No contact with the shaft. Accessories Storage Interval Depending on the interval and storage conditions, it is necessary to protect the internal components of the HYDRAULIC parts. These operations must be performed before storing components or before stopping use of the machine. Storage interval (months) Legend Circuits A - No specific precaution; only check the proper mounting Climate 3 6 12 24. of the plugs and covers. Temperate A B C C B - Fill up with HYDRAULIC fluid Tropical B C D D C - Rinse with storage fluid Maritime C D D D D - Fill up with storage fluid.

10 Oils Open air storage areas must not be used. The MOTORS must not be placed directly on the ground. Watch out: If a motor falls during handling, it will have to be reconditioned before it is used. Startup Paint Leave the bearing surfaces unpainted. Use paints compatible with the existing base coat. When applying paint, protect the shaft's lip seal. The paint could dry it and cause it to leak. The poclain Hydraulics components (like any mechanical component) can rust. They must be effectively and regularly protected according to the environment where they are used.