IK1201299 Engine Oil Capacities Page 1 9

1 Less InfoCountries: CANADA, UNITED STATESD ocument ID: IK1201299 Availability: ISIS, FleetISIS, NotSIRR evision: 10 Major System: ENGINESC reated: 7/10/2015 Current Language: EnglishLast Modified: 9/9/2019 Other Languages: NONEA uthor: Dan MyersViewed: 12084 Hide DetailsCoding InformationCopy LinkCopy Relative LinkBookmarkAdd to FavoritesPrintProvide FeedbackHelpfulNot HelpfulView My Bookmarks3267 Title: Engine Oil CapacitiesApplies To: All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISXCHANGE LOGP lease refer to the change log text box below for recent changes to this article: 09/03/2019 - Correct N13 capacity 08/29/2019 - Added PSI Gas verbiage 07/08/2019 - Revised ISB capacity 09/20/2018 - Add X15, , PSI Gas & International 01/18/2018 - Add A26 DESCRIPTIONThis document provides the User with a quick reference to Engine oil Capacities with oil filter Capacities may differ for various applications.

2 Add the minimum amount of oil recommended per Engine Manufacturer. Start the Engine to circulate the oil. Check the oil level per the Manufacturers procedure. Adjust the oil level as needed. 1994 - 2003 EngineESN RangeCapacity w/ Filter Change DT/HT466E/530E (3 Box & CEC)0933834 - 119403826L (28 QT)T444E0000500 - 599999913L (14 QT)2004 - 2006 EngineESN RangeCapacity w/ Filter Change DT/HT466E/530E (EGR)2000000 - 299999928L (30 QT)Page 1 of 9IK1201299 - Engine Oil Capacities10/2/2019 (15 QT)VT3650000500 - 599999918L (19 QT)2007 - 2009 EngineESN RangeCapacity w/ Filter Change MaxxForce DT/9/103000000 - 330000028L (30 QT)MaxxForce 5 All14L (15 QT)MaxxForce 70434544 - 530000118L (19 QT)2010 - 2013 EngineESN RangeCapacity w/ Filter Change MaxxForce 11/133000000 - 3300000 40L (42 QT)MaxxForce DT/9/10 3000000 - 330000028L (30 QT) MaxxForce 5 All14L (15 QT) MaxxForce 7 0434544 - (20 QT) MaxxForce 7 (TerraStar Only)0434544 - (22 QT)

3 Page 2 of 9IK1201299 - Engine Oil Capacities10/2/2019 +EngineESN RangeCapacity w/ Filter Change N9/N103540000+28L (30 QT)Page 3 of 9IK1201299 - Engine Oil Capacities10/2/2019 RangeCapacity w/ Filter Change N134400000+40L (42 QT)Page 4 of 9IK1201299 - Engine Oil Capacities10/2/2019 RangeCapacity W/Filter ChangeA264500000+40L (42 QT)Page 5 of 9IK1201299 - Engine Oil Capacities10/2/2019 RangeCapacity W/Filter Change International TBD (10 QT)Page 6 of 9IK1201299 - Engine Oil Capacities10/2/2019 7 of 9IK1201299 - Engine Oil Capacities10/2/2019 RangeCapacity W/Filter LPGAll7L ( QT) GasolineAll7L ( QT)EngineCapacity: Standard Oil Pan W/Filter Capacity: High Capacity Oil Pan W/Filter Capacity: Standard Oil Pan W/Stiffener Block Capacity: Stamped Steel Oil PanCapacity: Aluminum Oil PanISB15L ( QT) ( QT) ( QT) ( QT)N/A (28 QT) (29 QT) L9 (24 QT) (28 QT) (27 QT) ISM26-34L (28-36 QT)N/AN/APage 8 of 9IK1201299 - Engine Oil Capacities10/2/2019 DetailsFeedback InformationViewed: 12083 Helpful: 326 Not Helpful: 7No Feedback FoundCopyright 2019 Navistar, Inc.

4 Primary recommendation is for the use of 15W-40 multigrade for normal operation at ambient temperatures above -15 C (5 F). The use of multigrade oil reduces deposit formation, improves Engine cranking in low temperature conditions and increases Engine durability by maintaining lubrication during high temperature operating conditions. Since multigrade oils have been shown to provide approximately 30 percent lower oil consumption, compared with monograde oils, it is important to use multigrade oils. While the preferred viscosity grade is 15-40, lower viscosity multigrades can be used in colder climates. (See Figure 1: Recommended society of automotive Engineers (SAE) Oil Viscosity Grades at Ambient Temperatures.)Oils meeting API CI-4, API CJ-4, and 10-30viscosity grade, must meet a minimum High Temperature/high Shear viscosity of cP, and ring wear/liner wear requirements of Cummins Inc.

5 And Mack tests. Thus, they can be used over a wider temperature range than 10W-30 oils meeting older API performance classifications. As these oils will have directionally thinner oil films than 15W-40 oils, top quality Fleetguard filters must be used above 20 C (70 F). Some oil suppliers might claim better fuel economy for these oils. Cummins Inc. can neither approve nor disapprove any product not manufactured by Cummins Inc. These claims are between the customer and oil supplier. Obtain the oil supplier's commitment that the oil will give satisfactory performance in Cummins engines, or do not use the : For ISX dual overhead camshaft engines, 10W-30 is not recommended for (52 QT) N/AN/A ( gal) (11 gal) OTHER RESOURCESM aster Service ManualPSI EnginesCummins QuickServe (User & Password required)SAE International ( society of automotive Engineers)API (American Petroleum Institute)Page 9 of 9IK1201299 - Engine Oil Capacities10/2/2019