Transcription of In-Sight® Micro Series Vision System Installation …
1 13 SpecificationsGeneral SpecificationsThe following sections list general specifications for the In-Sight Micro Vision 3-1: In-Sight Micro Vision System SpecificationsSpecificationIn-Sight 1020/1050In-Sight 1100/1110In-Sight 1100 CIn-Sight 1400/1410In-Sight 1400 CIn-Sight 1403/1413In-Sight 1403 CMinimum Firmware RequirementIn-Sight version version version version version version non-volatile flash memory; unlimited storage via remote network Processing128 MBImageSensor1/3-inch CCD1 CCDS ensor Properties diagonal, x m sq. diagonal, x m sq. pixelsResolution (pixels)640 x 4801600 x 1200 Electronic Shutter Speed16 s to 1000ms27 s to 1000msAcquisition1 Rapid reset, progressive scan, full-frame grey levels (8 bits/pixel)24 bit color256 grey levels (8 bits/pixel)24 bit color256 grey levels (8 bits/pixel)24 bit colorGain/Offset controlled by full frames per second57 full frames per second60 full frames per second58 full frames per second14 full frames per second7 full frames per secondLens TypeCS-mount and C-mount (with 5mm extension, included).
2 CCD Alignment Variability2 ( ), (both x and y) from lens C-mount axis to center of opto-isolated, acquisition trigger software commands via Ethernet. (RS-232C available when using the optional CIO- Micro or CIO- Micro -CC I/O module.)Discrete InputsNone. (Eight additional inputs available when using the optional CIO- Micro , CIO- Micro -CC or CIO-WENET (750-341) I/O module.)Discrete Outputs2 opto-isolated, NPN/PNP high-speed outputs. (Eight additional outputs available when using the optional CIO- Micro , CIO- Micro -CC or CIO-WENET (750-341) I/O module.)Status LEDsNetwork, 2 Ethernet port, 10/100 BaseT with auto MDI/MDIX. Supports DHCP (factory default), static and link-local IP address (RS-232C: 1200 to 115,200 baud rates when connected to a CIO- Micro or CIO- Micro -CC I/O module).PowerClassClass 2 Power over Ethernet (PoE) and zinc M3 threaded mounting holes (1/4 - 20 and M6 mounting holes also available on mounting block).
3 Dimensions30mm ( ) x 30mm ( ) x 60mm ( )Weight121g ( ) without mounting ( ) with mounting Operating: 0 C to 45 C (32 F to 113 F) Storage: -30 C to 80 C (-22 F to 176 F) Humidity90%, non-condensing (Operating and Storage) ProtectionIP51 with cables and lens G shock with 50 gram lens attached per IEC G from 10-500 Hz with 50 gram lens attached per IEC ComplianceCE, FCC, TUV SUD NRTL, RoHS1. Maximum frames per second is job-dependent and based on the minimum exposure for a full image frame Expected variability in the physical position of the CCD, from Vision System -to- Vision System . This equates to ~ 17 pixels on a 640 x 480 resolution CCD and ~ 29 pixels on a 1600 x 1200 resolution 3-1: In-Sight Micro Vision System Specifications (Cont.)SpecificationIn-Sight 1020/1050In-Sight 1100/1110In-Sight 1100 CIn-Sight 1400/1410In-Sight 1400 CIn-Sight 1403/1413In-Sight 1403 CSpecifications25In-Sight Micro Vision System Dimensional DrawingsFigure 3-7: In-Sight Micro Vision System DimensionsNote: All dimensions are in millimeters [inches] and are for reference purposes only.
4 All specifications may be changed without .. [.12]2X M3 . [.18]2X M3 ..7526 Figure 3-8: In-Sight Micro Vision System Dimensions (with Mounting Block) .. UNC .. [.50]3X M6 X.
