INCOMPLETE VEHICLE DOCUMENT 2015 MODEL ... - Ram …

1 (1) 11?24/2014 2015 PROMASTER INCOMPLETE VEHICLE DOCUMENT 68188893AD CHRYSLER GROUP LLC 800 CHRYSLER DRIVE AUBURN HILLS, MI 48326-2757 CAUTION DO NOT REMOVE THIS DOCUMENT FROM THE VEHICLE INCOMPLETE VEHICLE DOCUMENT 2015 MODEL YEAR RAM PROMASTER VAN CHASSIS CAB AND CHASSIS CAB CUTAWAY VERSIONS The purpose of this DOCUMENT is to provide information and direction to subsequent manufacturers who must certify compli- ance of vehicles manufactured in two or more stages with the United States Federal Motor VEHICLE Safety Standards and the Canada Motor VEHICLE Safety Regulations, and other regulations applicable to the USA and/or Canada. This DOCUMENT is provided in accordance with 49 CFR Part 568 - Vehicles Manufactured in Two or More Stages (National Highway Traffic Safety Administration), and section 6, Regulations Respecting Safety for Motor Vehicles and Motor VEHICLE Components under Motor VEHICLE Safety Act (Transport Canada).

2 Upon completion of this VEHICLE , the final-stage upfitter, alterer or manufacturer must place a completed VEHICLE Tire and Loading Placard on driver's side B-Pillar of the VEHICLE , as required by CMVSR/FMVSS 110 and/or 120. The sticker below shows the information you will need for the VEHICLE Placard. AFFIX FEDERAL OR CANADA INCOMPLETE VEHICLE CERTIFICATION LABEL HERE AFFIX TIRE LOADING LABEL HERE (2) INTRODUCTION Information in this manual is furnished pursuant to United States and Canadian safety regulations or, in some cases where the information is not required by regulation, is furnished for the convenience of intermediate or final stage VEHICLE manufacturers. INCOMPLETE vehicles manufactured for sale or importation into the , are specially equipped for the United States. The descriptions and statements contained in the manual relate only to motor VEHICLE safety standards issued under the National Traffic and Motor VEHICLE Safety Act of 1966 as amended.

3 An INCOMPLETE VEHICLE manufactured for sale or importation into Canada is specially equipped for Canada. This VEHICLE conforms to the applicable Canadian Motor VEHICLE Safety Standards (CMVSS) on the date of manufacture printed on the cover of this manual. Requirements unique to vehicles for use in Canada are identified in the Statements of Conformity and the Canadian Vehicles sections of this manual. The Emission Certification Information section of this manual contains information regarding conformity to exhaust emission regulations of the United States, Canada, and the State of California and fuel economy regulations of the United States. This manual should not be relied upon with respect to compliance with any regulation of the Federal Highway Administration or regulations issued pursuant to the Occupational Safety and Health Act (OSHA) or any other Federal, state, or local regulations governing the performance or construction of motor vehicles (except for those requirements shown in the Information Certification Information section of this manual under the heading Unleaded Gasoline Label, Warranty and Maintenance, and Emission Control Information Label.)

4 It is the responsibility of the final stage manufacturer to determine applicability and comply with any Federal, state, or local requirements not detailed in this manual. IMPORTANT: UNITED STATES VEHICLES Chrysler Group LLC has endeavored, whenever possible, to state the specific conditions under which an INCOMPLETE VEHICLE may be completed to conform to each applicable Federal Motor VEHICLE Safety Standard. These specific statements are intended to aid subsequent stage manufacturers in avoiding instances of inadvertent noncompliance to particular standards. Note that the final responsibility for the compliance of the completed VEHICLE rests with the final stage manufacturer who is required by law to certify, as prescribed by Title 49, Code of Federal Regulations, Part , that the completed VEHICLE conforms to all applicable Federal Motor VEHICLE Safety Standards and that all applicable Federal, state and California emission/noise standards are conformed with.

5 Chrysler Group LLC does not make any representation as to the appropriateness of modifications for any particular application other than expressly stated herein. Intermediate and final stage manufacturers must exercise proper engineering judgment to determine if a modification is appropriate for their specific application. IMPORTANT: UNITED STATES AND CANADIAN VEHICLES The following safety standards information is valid only if this VEHICLE is completed as one of the VEHICLE types shown on the Unites States or Canadian certification label on previous page. (3) GENERAL INFORMATION Information in this section is provided pursuant to Title 49, Code of Federal Regulations, Part 568 Vehicles Manufactured in Two or More Stages , and Section 6 of the Canadian Motor VEHICLE Safety Regulations (CMVSR) Vehicles Manufactured in Stages.

6 Part 568 specifies that Final Stage Manufacturers must complete vehicles in compliance with all applicable Federal Motor VEHICLE Safety Standards and affix a label to each INCOMPLETE VEHICLE that is completed in accordance with Section of the CMVSR provides labeling requirements for vehicles that are to be sold in Canada. STATEMENTS OF CONFORMITY The Statements of Conformity section of this manual lists the Federal Motor VEHICLE Safety Standards in effect on the date of manufacture of this INCOMPLETE VEHICLE that are applicable to the type(s) of completed vehicles into which this INCOMPLETE VEHICLE may be manufactured. This date is shown on the label affixed to the cover of this manual. These statements, in most cases, apply to specific types of INCOMPLETE or completed vehicles and identify GVWR and UVW weight ranges. The INCOMPLETE VEHICLE type is identified by the 3rd digit of the VEHICLE Identification Number (VIN).

7 This digit is the number 7 on INCOMPLETE vehicles. Each statement of conformity is identified by a safety standard number located at the left margin. Because there may be multiple statements of conformity for each safety standard, use care to select the appropriate statement. Unique CMVSS requirements will be identified at the conclusion of the representations for a particular safety standard. Compliance statements provided in this manual are of the three following types ( ): Type I A statement that the VEHICLE , when completed, will conform to the standard if no alterations are made in identified components of the INCOMPLETE VEHICLE . Type II A statement of specific conditions of final manufacture under which the INCOMPLETE VEHICLE manufacturer specifies that the completed VEHICLE will conform to the standard.

8 Type III A statement that conformity with the standard cannot be determined based upon the components supplied on the INCOMPLETE VEHICLE , and that the INCOMPLETE VEHICLE manufacturer makes no representation as to conformity with the standard. IMPORTANT: To rely on the compliance representations in this manual, the INCOMPLETE vehicles must be completed as one of the completed VEHICLE types designated on the label affixed to the cover of this manual, and must not exceed the specified GVWR, GAWRs, or the Unloaded VEHICLE Weight limits when specified in this manual. (4) INCOMPLETE VEHICLE MANUAL COVER The cover of this manual identifies the INCOMPLETE VEHICLE configuration for which compliance representations are contained in this manual. Also, a label is affixed to the cover which includes the VEHICLE Identification Number (VIN) for the specific VEHICLE to which this manual belongs.

9 The label identifies the following information which pertains only to the VEHICLE with the corresponding VIN. The GVWR The front and rear GAWRs Tire and wheel size Cold tire inflation pressure (kPa/PSI) Completed VEHICLE type(s) into which the INCOMPLETE VEHICLE may be manufactured INCOMPLETE VEHICLE INFORMATION LABEL All INCOMPLETE vehicles manufactured by Chrysler Group LLC will have an INCOMPLETE VEHICLE Information label affixed to the driver-door lock pillar. California Air Resources Board (CARB), requires a VEHICLE Identification Number (VIN) Label having a non-contact, bar-code, reading wand capability. The bar-code directly below the VIN on the INCOMPLETE VEHICLE Information label, when provided, will comply with this regulation. The Canadian Motor VEHICLE Safety Act and Regulations require installation of an INCOMPLETE VEHICLE Information label with the National Safety mark on it on vehicles manufactured for sale in Canada.

10 STATEMENTS OF CONFORMITY The following Statements of Conformity apply to vehicles that are produced for sale or importation into the United States or Canada. The term INCOMPLETE VEHICLE Types in these statements refers to the type of the VEHICLE illustrated on this manual s cover and listed in the chart on page 8. The number preceding each Statement of Conformity refers to the number designation for a Part or a Section of Part 571 of the Federal Motor VEHICLE Safety Standard. The statements provided for each safety standard number are appropriate compliance representations for each Canadian safety standard number if this INCOMPLETE VEHICLE , identified by the VIN on the front of the DOCUMENT , was manufactured by Chrysler Group LLC for sale or use in Canada, except as may be noted at the conclusion of each safety standard number. (5) The following safety standards information is valid only if this VEHICLE is completed as one of the VEHICLE types shown on the United States or Canadian certification label on the previous page.