Transcription of Installation Dimensions
1 Installation DimensionsModel 16FF105 Model 16AF465 Model 16CF545 NOTE: Installation drawings are available at under Products _____Performance DataTorque (1)ContinuousIntermittentPeak30,000 in-lbs45,000 in-lbs60,000 in-lbs2,500 ft-lb3,750 ft-lb5,000 ft-lb3,390 Nm5,080 Nm6,780 :1 Speed (1)3600 RPM intermittent input speedRadial Load Rating (1)Weight67 - xxx lbs ( ? kg)Application InformationReducer life is affected by torque, speed, radial and axial load. Reducer life is also dependent on the dutycycle of the application. We define the duty cycle as an operation beginning with start and ending with afull stop or reversal. Typical components of the duty cycle are starting, running, reversing, overrunning andstopping. Life of the internal bearings is one of the limiting factors; consequently applications the requiresimultaneous high speed and high torque will have shortened Gear can help you estimate reducer life for your specific application.
2 Contact us with your duty cycleand life requirements and we can simulate reducer design life. Customer testing of the reducer in thespecific application is recommended to determine actual life.(1) Ratings are based on using 85W-140 gear Position (inches from CF)Load Value (Pounds)Output Shaft OptionsMotor Adapter OptionsSun Gear (Input Shaft) OptionsMotor Shaft LengthsFrom Motor Mounting flange to the end of the shaftSun Gear #Hydraulic Motor Shaft TypeMin. Length - in (mm)Max. Length - in (mm)16B7/8 - 13 Tooth ( ) ( )16C1 - 15 Tooth ( ) ( )16D1 Straight ( ) ( )16 ECharlynn 2000 BearinglessN/AN/A16 FCCharlynn 4000 Compact BearinglessN/AN/A16 FCharlynn 4000 BearinglessN/AN/A16H1 1/4 Straight ( ) ( )16I1 1/4 - 14 Tooth ( ) ( )16M1 SAE 6B ( ) ( )16O7/8 Straight Keyed????16P1 1/8 Straight Keyed????16 SDanfoss OMSS BearinglessN/AN/ASun GearsSAE A, 2&4 BoltSAE B, 2 BoltCode 4 Code 5 SAE B, 4 BoltSAE C, 2&4 BoltCode 0 Code 6 Sun Gear(Input Shaft Adapter)Order Information & Model CodesCodeDescriptionCodeDescription1 - Mounting Flange Base Model3 - Motor Adapter16FF Front Flange0 SAE B, 4 Bolt16AF Round Flange (1)4 SAE A - 2 & 4 Bolt combination16CF Center Flange5 SAE B - 2 Bolt2 - Output Shaft Options6 SAE C - 2 & 4 Bolt Straight Keyed4 - Ratio24 Bolt Flanged Shaft with 1/2.
3 1224 Bolt Flanged Shaft with 5/8 studs5 - Design J501 Taper6 Current Design416 Tooth 8/16 Spline6 - Special Options (2)55 Bolt Flanged Shaft with 1/2 studsA22 Nickel Plated Shaft & Seal Carrier525 Bolt Flanged Shaft with 5/8 studsA32 Magnetic Speed Straight 2 9/16 Round with CrossDrilled Hex with Cross Drilled SquareSample Model Code12345616FF1456A22 Sun Gear Kit Model Code16B7/8 - 13 Tooth Spline16H1 1/4 Straight Keyed16C1 - 15 Tooth Spline16I1 1/4 - 14 Tooth Spline16D1 Straight Keyed16M1 SAE 6B Spline16 ECharlynn 2000 Bearingless16O7/8 Straight Keyed16FC Charlynn 4000 Compact Bearingless16P1 1/8 Straight Keyed16 FCharlynn 4000 Bearingless16 SDanfoss OMSS BearinglessNote: Mounting bolts and o-rings or gaskets are RecommendationFor maximum speed reducer life the recommended oil is SAE 85W-140 Multi-grade gear oil meeting API-GL5 and API-MT1 service.
4 Alternate oil that will provice adequate speed reducer life is SAE 90W gear oilmeeting API-GL5 and API-MT1 service. These oils should be readily available at your local automotivestore or lubricant using a Bearingless hydraulic motor or Flow Through lubrication where hydraulic oil from thehydraulic motor lubricates the speed reducer an ISO 68 hydraulic oil with EP1 additives and a minimum zinc anti-wear additive will provice adequate speed reducer oil temperature should not exceed 1600 F (700 C) for continuous operation or 1800 F (800 C) forintermittent Heco Gear for applications requiring use of non-petroleum based or fire retardant : Warranty information and Parts & Service manuals (pdf format) are available at (1)Interchange mounting for: Auburn 6T, 6S, 7S & Fairfield S1A(check pilot Dimensions .(2)Units with A suffix denote special modifications; ConsultHeco.)
