Transcription of Installation Guide IntelliGuard 770 - Ampire
1 2006 Directed Electronics Vista, CA N919621 11-06 Installation GuideIntelliGuard 770 Bitwriter , Code Hopping , Directed , Doubleguard , ESP , FailSafe , Ghost Switch , Learn Routine , Nite-Lite , Nuisance Prevention Circuitry , NPC , Revenger , Silent Mode , Soft Chirp , Stinger , Valet , VehicleRecovery System , VRS , and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics,Inc., Vista, !!Please note that this manual was intended for US consumersand therefore includes American phrases or !
2 Safety first ..1before beginning the installation2after the Installation ..2transmitter functions ..3standard configuration ..3primary harness wire connectionguide ..4primary harness wiring diagram 4primary harness wiring Guide ..5secondary harness wire connectionguide ..8secondary harness wiring diagram8secondary harness wiring Guide 8immobilizer harness wire connec-tion Guide ..9immobilizer harness wiring ..9ultrasecure immobilizer ..10immobilizer jumper setting ..10door lock harness wire connectionguide.
3 10type A: positive (+) 12-volt pulse .11type B: negative (-) pulse ..12type C: reversing polarity ..13type D: after-market actuators 14type E: mercedes-benz and audi(1985 & newer) ..15type F: one-wire system ..16type G: positive (+) multiplex .17type H: negative (-) multiplex .18peripheral plug-in harnesses ..19super bright blue led, 2-pin whiteplug ..19plain-view valet ..19sensor harness, 4-pin connector .19mounting the receiver/antenna 20arming/disarming diagnostics ..21arming ..21disarming ..21system status chirps.
4 22remote siren silencing ..22multiple event total recall ..22table of zones ..22system features programming ..23cliffnet wizard pro installationsoftware programming ..23manual programming instructions24user selectable features ..25user selectable features descrip-tions - column one ..26user selectable features descrip-tions - column two ..27user selectable features descrip-tions - column three ..28installer selectable features ..30installer selectable featuresdescriptions - column one ..31installer selectable featuresdescriptions - column two.
5 32installer selectable featuresdescriptions - column three ..33programming notes ..34fact II - false alarm control technol-ogy ..36smart power up II ..37remote control sensor disable ..37mux sensors ..37audio sensor ..37adjusting the audio sensor ..37auto-immobilization feature ..38auto-immobilization sequence 38one-time valet feature ..38blackjax feature ..39blackjax activation sequence ..39blackjax deactivation sequence 40bypass blackjax temporarily (if onin program grid) ..40remote adjustable omnisensor.
6 40installing the omnisensor ..40adjusting the omnisensor ..40second unlock feature ..42troubleshooting ..42wiring reference Guide ..44notes ..48 2006 directed electronics1warning! safety firstThe following safety warnings must be observed at all times:zDue to the complexity of this system, Installation of this product must only be per-formed by an authorized clifford properly installed, this system can start the vehicle via a command signalfrom the remote control transmitter. Therefore, never operate the system in anarea that does not have adequate ventilation.
7 The following precautions are thesole responsibility of the user; however, authorized clifford dealers should makethe following recommendations to all users of this system: operate the system in an enclosed or partially enclosed area withoutventilation (such as a garage). parking in an enclosed or partially enclosed area or when havingthe vehicle serviced, the remote start system must be disabled using theinstalled toggle is the user's sole responsibility to properly handle and keep out of reachfrom children all remote control transmitters to assure that the system doesnot unintentionally remote start the USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN ORABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
8 ALL DOORSLEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED ORPARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMESREMAIN of this product in a manner contrary to its intended mode of operation mayresult in property damage, personal injury, or death. Except when performingthe Safety Check outlined in this Installation Guide , (1) Never remotely start thevehicle with the vehicle in gear, and (2) Never remotely start the vehicle with thekeys in the ignition. The user will be responsible for having the neutral safety fea-ture of the vehicle periodically checked, wherein the vehicle must not remotelystart while the car is in gear.
9 This testing should be performed by an authorizedClifford dealer in accordance with the Safety Check outlined in this productinstallation Guide . If the vehicle starts in gear, cease remote start operation imme-diately and consult with the user to fix the problem the remote start module has been installed, test the remote start module inaccordance with the Safety Check outlined in this Installation Guide . If the vehi-cle starts when performing the Neutral Safety Shutdown Circuit test, the remotestart unit has not been properly installed.
10 The remote start module must beremoved or properly reinstalled so that the vehicle does not start in gear. Allinstallations must be performed by an authorized clifford dealer. OF THE REMOTE START MODULE IF THE VEHICLE STARTS INGEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATINGTHE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT INPROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USEOF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE STARTMODULE.
