Installation Guide - Wallbox Academy

1 Installation GuideGu a de instalaci nInstallationsanleitungGuide d installationInstallatiegidsGuida per I installazioneInstallasjonsveiledningInst allationsguideManual de instala oPULSAR PLUSE nglish Espa olDeutschFran aisNederlandsItalianoNorskSvenskaPortugu s 3-1415-2627-3839-5051-626 3 -7 475-8687-9899-1103 ENContentsSafety RecommendationsLegal NoticeSafety InstructionsProduct DescriptionInstallation InstructionsElectrical ProtectionDimensions and Positioning of the DeviceDrillMountingStartupUser GuideMaintenanceLimited WarrantyService44458899913131314144 ENDisregard of or actions contrary to the safety information and instructions contained in this manual and printed on the device may lead to electric shock, fire and/or severe injury and either damage to the vehicle or to the Wallbox device.

2 Any resulting damage from such actions is excluded from the warranty. The Installation of the Wallbox device must be performed by a qualified electrician in accordance with the perceptive regulation. The information provided in this Installation Guide does not relieve the user of responsibility to follow all norms and standards or local regulations that may apply. The Wallbox charger device has been designed, developed and manufactured to satisfy requirements, safety dispositions and norms in accordance with the directives presented in the declaration of conformity.

3 Do not operate if physical defects such as cracking, breakage, corrosion, or other damage are observed. In this case, please contact your distributor. Only an authorised specialist and qualified personnel may open, disassemble, repair, alter or modify the Wallbox device. Unauthorised modification of the Wallbox equipment makes manufacturer warranty void. Unauthorised modifications or conversions are not allowed. Do not delete any warning on the device, such as safety symbols, warning notices, rating plates, identification plates or cable markings.

4 Protect your Wallbox device from any impact which it may be exposed. The charging station does not have its own power switch. Always respect local electricity rules and regulations, as relevant. Wallbox chargers can only be used under the operating parameters specified and within the normal ambient conditions described in the Product Description. Do not use your Wallbox charger under adverse climatic conditions that could affect the vehicle or the Wallbox device. Do not open the cover in the NoticeThis document is intended to be used as a reference Guide for the Installation and operation of the charger.

5 The product images shown are for illustration purposes only and may not be an exact representation of the product. Wallbox reserves the right to make changes to the specifications and processes of the product and documentation at any time without prior all of the safety instructions and take special care to keep this manual handy. This Installation manual is intended for qualified personnel user must read and fully understand the safety instructions RecommendationsSafety Instructions5 Important information for the correct disposal of the product in accordance with Directive 2012/19/EC.

6 At the end of its useful life, the product will not be disposed of as urban waste. It must be taken to a collection center for special and differentiated waste or to a distributor that provides this service. Connector Recommendations Always check the charging cable and the contacts for damage and contamination before use. Never use a damaged charging cable, the vehicle plug, or the infrastructure electrical outlet to charge. Never use contacts that are dirty or wet. Only connect the connector to vehicle plug and infrastructure electrical outlets that are protected against water, moisture and liquids.

7 After stopping the charging process, the vehicle connector and the equipment plug can be disconnected. Never use force to disconnect the vehicle connector from the inlet or the equipment plug power outlet. Such dangerous activity can cause serious injuries or even death. Depending on the charging station and the electric vehicle, the time to complete the charging process and the duration of unlocking may vary. Some vehicles can be started with the charging cable connected. Be sure to unplug before driving off.

8 Do not use the charging cable with an extension cable or an adapter. If the connector emits smoke or begins to melt, never touch the charging cable. If possible, stop the charging process. In any event, disconnect the power supply from the Wallbox device. Keep the charging cable out of the reach of children. Be careful with the connector, do not step on it or on the cable. The cable should NOT be tightened under ANY CIRCUMSTANCES while connected to the DescriptionIntroductionWallbox Pulsar Plus is a practical, intelligent charging system for electric vehicles and plug-in hybrids, which connects to the myWallbox charging management platform using Wi-Fi or Bluetooth.

9 The Pulsar Plus comes with the addition of integrated DC leakage protection as Plus is compact, at just 16 cm square, and features the most advanced technology to provide maximum charging performance. Pulsar Plus easily adapts to any Installation , in private garages or shared SpecificationsElectrical SpecificationsUser Interface and CommunicationsMaximum outputConnectivityUser kW (1P) / 22 kW (3P)[2]Wi-Fi / BluetoothMaximum currentUser interface32 A, 5x6 mm cableWallbox App / myWallbox PortalRated frequency50 Hz / 60 HzInput voltage110 / 230V AC 10% (1P) / 400V AC 10% (3P)

10 [2] Wallbox App / myWallbox PortalCharger status informationCharging current configurable from 6 A to 32 AHalo RGB LED / Wallbox App / myWallbox PortalProtection ratingIncluded featuresOptional featuresIP54 / IK08 Power Sharing SmartPower BoostSurge categoryResidual current detectionRCCBM odelPulsar PlusCable lengthConnector type5m (7m optional)[1]Type 1 (SAE J1772) or Type 2 (IEC 62196 -2)Dimensions166x163x82 mm (without cable)Charging modeMode 3 Weight1 kg (without cable)Operating temperatureStorage temperatureCE Mark-25 C to 40 C-40 C to 70 CLVD 2014/35/EU, EMCD 2014/30/EU IEC61851-1,IEC61851-22, IEC62196-1 CAT IIIAC 30 mA / DC 6 mAExternal RCCB required[3] [1] Only available for Type 2 3P chargers.