Installation Instructions for Self Powered L.E.D. Exit ...

1 self Powered EXIT INSTALLATIONWALL MOUNTINGStep the circuit at the junction box (J-box) where the exit sign isto be unswitched 24 hour AC supply of rated voltage from the the black, orange, and white extension leads and wire nuts provid-ed. Determine the line voltage to be supplied to the exit and follow theinstructions in the table :If the junction box is not grounded, attach ground wire to hole marked"gnd" on mounting plate with green grounding screw the exit sign stencil and backplate from the exit out the appropriate mounting pattern and the wire pass hole inthe exit backplate to fit the J-box being the extension leads through the wire pass hole and securelymount the exit sign backplate to the J-box.

2 Snap the exit frame ontothe the backplate clip and the exit sign wire channels route the exten-sion leads to the appropriate push-in connector per the and strip (strip length .375 ) any excess wire allowing enough slack toinsert the stripped ends into the appropriate push-in the wires into the appropriate push-in AC supply, LED display will come the exit stencil back on the exit Installation Instructions for self Powered Exit SignsLPX SeriesIMPORTANT SAFEGUARDSWHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYSBE OBSERVED INCLUDING THE AND FOLLOW ALL SAFETY Do not use Do not mount near gas or electric Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by The use of accessory equipment not recommended by SURE-LITES may cause an unsafe Do not use this equipment for other than its intended THESE &SLIDEINSERT &SLIDECEILING MOUNTEND MOUNTC ustomer First Center 1121 Highway 74 South Peachtree City.

3 GA 30269116/07024-74 DLine Voltage to besuppliedJ-Box 120V line J-box 277V lineJ-box Neutral line120 VoltsExtend using theblack leadN/AExtend using thewhite lead277 VoltsN/AExtend using theorange leadExtend using thewhite leadCEILING OR END MOUNT INSTALLATIONStep sure to use SURE-LITES LPX Canopy steps 1 to 2 of wall mounting the provided screws in the canopy screw holes. Tabs inside the holes will prevent the screws from falling out during Installation . Step the extension leads through the canopy nose and securely fasten the canopy to the J-box with the screws. If necessary, auniversal mounting strap is provided for Installation on different J-box configurations. The mounting strap can also be used to aim thesign in different the exit sign stencil from the exit double face sign is required, convert the single face sign supplied.

4 Replace back plate with extra stencil and color sheet supplied withthe the mounting hole plug on the top (ceiling mount) or side (end mount) of the the extension leads through the unplugged mounting the canopy nose through the mounting hole until the side of the frame touches the canopy. Lock the frame onto the canopy bysliding the frame in a direction parallel to the canopy length toward the narrow end of the mounting hole. Slide the frame until both snapsengage the canopy nose preventing any motion back out of the the exit sign wire channels route the wires to the appropriate push-in connector per the steps 7 to 10 of the wall mount :None required. Replace the batteries every 8 to 10 years according to ambient.

5 However, we recommend that the equipment be tested regularly in accordance with local :Servicing of any parts should be performed by qualified personnel. ONLYuse replacement parts supplied by SURE-LITES . For replacement transformer, battery, or LED display PC board, see the fixture :1. Depress the test switch. The LED display will remain lit when switched to battery power2. Release the test switch. The LED display will operate with AC :This equipment is furnished with a sophisticated low voltage battery dropout circuit to protect the battery from over discharge after its useful output has been used. Allow 24 hours recharge time after Installation or power failurefor full load SHOOTING HINTS:IF LED DISPLAY OR CHARGE INDICATOR LAMP DOES NOT ILLUMINATE, CHECK THE FOLLOWING:1.

6 Check AC supply - verify unit has 24 hour AC Unit is shorted or battery is not connected. 3. Battery discharged, Permit unit to charge for 24 hours and then following the above trouble shooting hints does not solve your problem, contact your local SURE-LITES representative or the factory forassistance. LED DISPLAY PC BOARD TRANSFORMERBATTERY(+) RED( - ) BLKCHARGE INDICATOR TESTSWITCHREDYELLOWRED WHITE BLACK ORANGE PUSH - IN CONNECTORORANGE - 277 VBLACK - 120 VWHITE - NEUTRALCONTRACTORCONNECTIONS SCHEMATICSURE-LITES NOTE:The LED display PC board listed herein, whenused according to these Instructions with this unit arein accordance with the requirements of CSA No. 141, Unit Equipment for First Center 1121 Highway 74 South Peachtree City, GA 30269226/07024-74 DSURE-LITES ENSEIGNE DE SORTIE AUTO-ALIMENT EINSTALLATION MURALE tape le courant la bo te de jonction (Bo te J) o l'enseigne de sortiedoit tre install e.

7 Tape une rallonge pour l'alimentation 24 heures non commut e detension nominale partit de la Bo te J. Utiliser les fils de rallonge noir,orange et blanc et les serre-fils fournis. D terminer la tension de secteur fournir l enseigne de sortie et suivre les indications dans le :Si la bo te de jonction n est pas mise la terre, attacher le fil de terre au trou avec la marque "gnd" sur la plaque de montage avec la vis verte de mise la terre. tape le stencil de l enseigne de sortie et la plaque arri re du cadre desortie. tape foncer les trous appropri s pour le montage et pour passer le fildans la plaque arri re de l enseigne de sortie correspondant la Bo teJ utilis e. tape passer les fils de rallonge dans le trou pour fils et fixer la plaquearri re de l'enseigne de sortie la Bo te J.

8 Attacher le cadre del enseigne de sortie sur la plaque arri re. tape 6. l aide de l agrafe sur la plaque arri re et des chemins de fils dansl enseigne de sortie, faire passer les fils de rallonge au connecteur enfoncer appropri , conform ment au sch ma. tape et d nuder (longueur du fil nu 0,925 cm (0,375 po)) tout exc dent de fil en laissant assez de mou pour ins rer les extr mit s d nud es dans leconnecteur enfoncer appropri . tape rer les fils dans le connecteur enfoncer appropri . tape sous tension. L affichage LED s allumera. tape le stencil de l enseigne de sortie sur la plaque arri re du cadre de D Installation des Enseignes de Sortie LED Auto-aliment es de la S rie LPXMESURES DE PROTECTION IMPORTANTESLORSQUE VOUS UTILISEZ UN APPAREIL LECTRIQUE, IL FAUT TOUJOURS PRENDRE DESMESURES DE S CURIT L MENTAIRES, NOTAMMENT : ET SUIVRE TOUTES LES CONSIGNES DE S CURIT.

9 2. Ne pas utiliser l appareil l ext Ne pas l'installer pr s d'un chauffage lectrique ou L appareil doit tre install des endroits et des hauteurs o il ne pourra pas tre facilement alt r par des personnes nonautoris SURE-LITES ne recommande pas l'utilisation d un dispositif accessoire car cela pourrait cr er une situation Ne pas utiliser cet appareil des fins autres que celles pour lesquelles il a t con CES RER ETFAIRE RER ETFAIRE AU PLAFONDFIXATION SURUNE EXTR MIT Customer First Center 1121 Highway 74 South Peachtree City, GA 30269336/07024-74 DLa tension desecteur fournirTension de secteur120 V de la Bo te J Tension de secteur227 V de la Bo te J Ligne neutre de laBo te J 120 VRallonger l aidedu fil noirS/ORallonger l aidedu fil blanc277 VS/ORallonger l aidedu fil orangeRallonger l aidedu fil blancSURE-LITES FIXATION AU PLAFOND OU SUR UNE EXTR MIT tape rifier de bien utiliser l ensemble de la base SURE-LITES LPX.

10 Tape les tapes 1 et 2 des Instructions pour Installation murale. tape les vis fournies dans les trous de vis de la base. Les languettes l int rieur des trous emp cheront les vis de tomber durantl Installation . tape passer les fils de rallonge dans le nez de la base et fixer la base la Bo te J avec les vis. Si n cessaire, une bride de montageuniverselle est fournie pour l Installation sur des bo tes J de configuration diff rente. La bride de montage peut galement tre utilis epour orienter l enseigne dans des directions diff rentes. tape le stencil de l enseigne de sortie et la plaque arri re du cadre de sortie. tape une enseigne double face est n cessaire, convertir l enseigne face simple fournie.