Installation Instructions Super 700 Series Sprinkler

1 IntroductionThe versatile Super 700 Series Sprinkler is designed to meet a wide range of applications in both residentialand commercial irrigation systems. For best results, read through the instruction manual completely first tofamiliarize yourself with the product specifications, recommended Installation methods and adjustment HeightBody HeightCapNozzleModelInlet(To Nozzle)Diameter(Overall)DiameterTrajecto ryS7003/4" FNPT3-1/2" mm2-3/8" cm6-7/8" cm3" cm25 & 15 S700C3/4" FNPT3-1/8" mm2-3/8" cm6-7/8" cm3" cm25 & 15 S700 HP3/4" FNPT10-3/8" cm2-3/8" cm16-1/2" cm3" cm25 & 15 S700S3/4" FNPT 1-3/4" cm5-1/8" cm 25 & 15 ModelWorking PressureMaximum PressureS70025 - 50 - kg/cm2172 - 345 kpa75 kg/cm2517 kpaS700HP25 - 50 - kg/cm2172 - 345 kpa75 kg/cm2517 kpaS700S25 - 50 - kg/cm2172 - 345 kpa75 kg/cm2517 kpaS700C25 - 60 - kg/cm2172 - 414 kpa75 kg/cm2517 kpaNozzlePressureRadiusFlowpsikpakg/cm22 5 Trajectory15 Trajectorygpmlpmm3 Performance (at nominal pressure)

2 IIII nnnnssssttttaaaallllllllaaaattttiiiioooo nnnn IIII nnnnssssttttrrrruuuuccccttttiiiioooonnnn ssssSuper 700 Series SprinklerInstallation ProcedureThe S700, S700C and S700 HP sprinklers are designed for Installation in-ground, aligned perpendicular tothe coverage area with the top of the cap level with compacted finish grade. When operated, the sprinklerriser will extend, positioning the rotating nozzle above the turf or ground cover. When turned off, the nozzleand riser will retract, by spring pressure, into the Sprinkler body S700S shrub Sprinkler is designed for Installation above ground on a riser, constructed from 3/4"(20mm) schedule 40 or 80 PVC or galvanized steel pipe, positioned perpendicular to the coverage of a flexible connection between the Sprinkler or shrub riser and the lateral line is a rigid connection, the flexible link enables easy, accurate positioning of the Sprinkler and helps protectthe PVC piping and fittings from breakage due to downward or lateral Sprinkler movement.

3 See Figure 1fortypical Installation to Figure 1, install the sprinklers as follows:1. Complete all pipe connections from lateral Thoroughly flush all dirt and debris from Thread Sprinkler onto 3/4 in. male NPT fitting and tighten by hand until snug : Use only TeflonTM tape on plastic threaded connections. Use of pipe dope or other pipesealing compounds may damage plastic Backfill soil around Sprinkler or shrub riser. Thoroughly compact soil around components to maintaincorrect Installation If Sprinkler nozzle is not installed, remove protective cover and install nozzle at this time. See NozzleInstallation and Removal Instructions on page Activate sprinklers and observe operation. If necessary, adjust part circle arc and/or spray radius asexplained in following sections: Part Circle Arc Adjustment (pages 3 - 5) , Spray Radius Adjustment (page 6).

4 2 Figure 1 - Installation MethodsFUNNYPIPE3/4" SxSxTTEES700 HP3/4" THREADEDCOUPLINGFUNNY PIPE3/4" SxSxTTEE3/4" MALE ELBOW(850-32)3/4" (20 mm) SCH 40 PVC, SCH 80 PVC ORGALVANIZED PIPES700 & S700CS700S3/4" SxSxTTEEFUNNYPIPE3/4" MALE ELBOW(850-32)3/4 "MALEELBOW(850-32)Nozzle Installation and RemovalNote:On part circle models, nozzle turret may ratchet to end of arc before nozzle seats or Circle Arc AdjustmentThe S700 part circle Sprinkler arc is adjustable from 40 330 . The left reversing point, located at the endof counterclockwise nozzle travel, is stationary or fixed and is notadjustable. Therefore, the left end of thearc must be aligned with the left watering border by turning the Sprinkler on its pipe fitting. This will establisha reference point for an increase or decrease adjustment to the right reversing point, which occurs at theend of clockwise nozzle Open water supply line to Sprinkler .

5 Turn nozzle by hand in same direction of current travel to reversingpoint at end of arc. Immediately rotate nozzle in opposite direction to reversing point at other end ofarc. This procedure enables arc to be viewed without waiting for nozzle to traverse at normal : Turning nozzle against current direction of travel may damage Sprinkler drive mechanism. 2. Using a small screwdriver or Super 700 Nozzle Tool and Wrench, turn lockpin 1/4 turn counterclockwise to align slot with A (adjust) on nozzle top. SeeFigure arc: See Figure 4and follow steps A - C on page Increasearc: See Figure 5and follow steps A - D on page 700 TOROSUPER 700 ALIGN ARROWWITH SLOTTORO700 Super 700 TOROSUPER 700 TOROSUPER 700 TOROSUPER 700To install nozzle:(Refer to Figure 2A.)

6 Pull lock pin up. Align arrow on nozzle top with slot in nozzle turret and insertnozzle. Using a coin or Super 700 Nozzle Tool & Wrench (89-1376), press and turn nozzle clockwise until seated inturret. Turn lock pin to align slot with L (lock) on nozzle top (part circle models only). Press lock pin down. To remove nozzle:(Refer to Figure 2B.) Turn lock pin to align slot with L (lock) on nozzle top (part circlemodels only). Pull lock pin up. Insert a coin or Super 700 Nozzle Tool & Wrench (89-1376)into slot on top of noz-zle. Turn nozzle counterclockwise to release. Lift nozzle out of nozzle 0 0 INSTALLALIGNARROWWITHSLOTREMOVEALF igure 3 TOROSUPER 700 TOROTOROSUPER 700 SUPER7 0 0 INSTALLALIGNARROWWITHSLOTREMOVEALTOROSUP ER 700 SUPER7 0 0 INSTALLALIGNARROWWITHSLOTREMOVEALF igure 2 BFigure 2 AContinue at top of page 4 - Decreasing ArcABCR otate nozzle clockwise to right(adjustable) end of down and turn nozzlecounterclockwise to align spraywith right border of watering pull up nozzle for proper arc of arc adjusted fromright will decrease right end endof arcStationary (fixed)end of arcContinue at top of page 5 - Increasing ArcABCE stimate additional amount of arcrequired to align nozzle with rightborder of watering nozzle counterclockwise to left(fixed)

7 End of down and turn nozzle clock-wise to add amount of arc estimat-ed in Step A. Immediately pullnozzle up and for proper arc of arc adjusted from leftend of arc will be added to right endof end of arcAdjustable endof arcArc increasedhereRight Border4. Turn lock pin 1/4 turn clockwise to align slot with L on nozzletop as shown in Figure Radius AdjustmentThe Spray Radius Adjustment Screw is provided primarily to reducethe radius (throw) of the spray without decreasing pressure to thesprinkler. (Reduction exceeding 25% of radius is not recommended.)In addition, it can also be used when the Sprinkler is operated at lowpressure to slightly diffuse the spray, preventing a possible dry areanear the : Adjustment screw can be swept into spray and lost ifturned Using a 1/16 in.

8 Hex wrench, turn adjustment screw inward(clockwise) as required to reduce/diffuse spray as shown inFigure Sprinkler (See Figures 8 - 11 to identify Sprinkler parts)S700, S700C and S700HP1. S700C and S700 HP Only: Using a 1/16" hex wrench, loosenset screw on side of Part Circle Models Only: To maintain correct arc alignment ofnozzle during reassembly, observe location of nozzle orificebefore disassembling Sprinkler components 3. Unscrew cap from body (carefully to avoid changing bodyalignment on pipe fitting). Remove Sprinkler assembly Pull basket screen and variable stator assembly from bottom ofriser Flush screen and stator assembly thoroughly with clean water to remove all Reassemble parts in reverse order. Align keyways in Sprinkler riser assembly with keys in body tomaintain correct radial location of nozzle.

9 Tighten cap by hand only S700C and S700 HP Only: Tighten cap set Unscrew Sprinkler body assembly from cap (base).2. Using small screwdriver, carefully pry screen and stator assembly from body Flush parts thoroughly with clean water and reassemble in reverse order. Tighten body by hand only 0 0 INSTALLALIGNARROWWITHSLOTREMOVEALF igure 6 SUPER7 0 0 INSTALLALIGNARROWWITHSLOTREMOVEALF igure 7 Note Nozzle Replacement Part NumbersAll S700 Sprinkler models manufactured afterDecember 1991 require a locking nozzle (desig-nated by an L after the part number). For S700sprinklers manufactured prior to December 1991,omit the L from the part number when Sprinkler versions as shown at peg model requires L type (withor with-out slot)Item Part , S700-PC, less Nozzle-35-8910 Sprinkler , S700-FC, less Nozzle-35-1656 Sprinkler , S700-PC, less Nozzle, w/Check Valve-35-1655 Sprinkler , S700-FC, less Nozzle, w/Check Valve-89-0612 Sprinkler , , , , , , LKit, Nozzle, , Yellow189-0893 LKit, Nozzle, , Orange189-0894 LKit, Nozzle, , Red189-0895 LKit, Nozzle, , Black189-0896 LKit, Nozzle, , Blue189-0897 LKit, Nozzle, , Green189-0898 LKit, Nozzle, , Tan189-0899 LKit, Nozzle, Gray189-1091 LKit, Nozzle, , Yellow, Low Angle 189-1093 LKit, Nozzle, , Orange, Low Angle189-1095 LKit, Nozzle, , Red, Low Angle189-1097 LKit, Nozzle, , Black, Low Angle189-1099 LKit, Nozzle, , Blue, Low Angle189-1101 LKit, Nozzle, Green, Low Angle189-1103 LKit, Nozzle, , Tan, Low Angle189-1105 LKit.

10 Nozzle, , Gray, Low Angle)Item Part , Set, Half Dog, 6-323360-0494O-Ring, .070 in. x .426 in. x .566 , Molded535-3145 Seal, Riser689-0995 Sleeve, Spring735-4508 Spring, Retraction835-8912 Riser Assy., FC835-8913 Riser Assy., PC9-----------Sleeve, Stator10-----------Diaphragm, Stator119-1691 Screen1289-0266 Valve, Check139-1661 BodyService ItemsN/S700-10 Kit, Cover, RubberN/S35-6323 Stator Assy., Variable (includes items 9 & 10)N/S89-1376 Super 700 Nozzle Tool & WrenchN/S89-3003 Lock, Nozzle Pin, Std. AngleN/S89-0323 Cover, Nozzle (For use with non L version nozzles onlyN/S89-0266 Check ValveN/S89-0805 Restrictor, Low Pressure7 Super TOROTOROTOROTORO45 678910 TOROSUPER TORO700 Super 700 TORO111213132 Figure 8 S700 Lawn8 Item Part , S700HP-PC, less Nozzle-35-8919 Sprinkler , S700HP-FC, less Nozzle-89-0707 Sprinkler , , , LKit, Nozzle, , Yellow189-0893 LKit, Nozzle, , Orange189-0894 LKit, Nozzle, , Red189-0895 LKit, Nozzle, , Black189-0896 LKit, Nozzle, , Blue189-0897 LKit, Nozzle, , Green189-0898 LKit, Nozzle, , Tan189-0899 LKit, Nozzle, , Gray189-1091 LKit, Nozzle, , Yellow, Low Angle189-1093 LKit, Nozzle, , Orange, Low Angle189-1095 LKit, Nozzle, , Red, Low Angle189-1097 LKit, Nozzle, , Black, Low Angle189-1099 LKit, Nozzle.