INSTALLATION, OPERATIONS AND USER’S MANUAL

1 Fully Aboveground InstallationsPartially In-Ground InstallationsFully In-Ground InstallationsINSTALLATION, OPERATIONS AND USER S MANUALO riginal Endless PoolThe entire endless pool system is ETL listed, Ref. #2001779 and conforms to UL Standard #1563. Individually, all electrical com-ponents of the endless pool are UL and/or CSA approved. As defined by the International Residential Code (IRC), the EndlessPool is considered an aboveground or an in-ground pool depending on the installation . That is to say, customers can install our End-less Pool Kit above-ground on a garage or basement floor or in the backyard or they can sink it partially or fully in-ground.

2 The unitis completely self-supporting. As required by the IRC the endless pool meets all the following standards: ANSI/NSPI Standards#3 (Permanently Installed Residential Spas), #4 (Aboveground/On-ground Residential Swimming Pools), #5 (Residential In-groundSwimming Pools), and #6 (Portable Spas). The appropriate governing standard is dependent on the installation method and the re-quirements and definitions used by the local governing electrical connections should be made by a licensed electrician in accordance with the current national and local electrical pool equipment including the 4 kW electric heater, circulating pump and 5 HP hydraulic power unit runs off one 30 amp, singlephase, GFCI protected, 220 volt service.

3 A minimum of 10 AWG wire should be used for all field wiring. We recommend you installa shut off within 5 of where you intend to place your power read this Owner s MANUAL and all associated Supplemental Guides prior to beginning your Instruction Booklet InformationInstallation Instructions Table of Contents Pool Arrival and Inspection.. 2 Site Preparation .. 2 Assembly of Pool Panels (Overview) .. 2 Automatic Retractable Security Cover.. 2 Optional Insulation.. 2 Liner Hanger .. 3 Optional Liner Hangers.. 4 Liner Underlayment.. 5 Liner.. 6 Thru-Wall Connections .. 7 Swim Current Component Assembly.. 7 Thru-Wall Connections.

4 7 Water Quality System.. 9 Skimmer-Filter installation .. 11 Keypad installation .. 14 Power Unit.. 14 Wiring.. 15 Bonding and Grounding.. 18 Heater/Controller.. 18 Water Quality Isolation Cover.. 19 Hydraulic Hose Connections.. 19 Optional Antenna Extension.. 19 Optional Retractable Security Cover System.. 20 Optional UV Sanitizer.. 20 Optional Treadmill.. 20 Optional Hydrotherapy Jets System.. 20 Optional Underwater Lights System.. 20 Optional Corner Step.. 21 Optional Interior Stair .. 21 Optional Swim Mirror.. 21 Optional Synthetic Coping System .. 21 endless pool Warranty.. 29 OPERATIONS and Maintenance Table of Contents Overview.

5 21 Filling Your endless pool .. 21 Pool Equipment and Startup.. 22 Balancing the Pool Water.. 24 How to Swim in an endless pool .. 25 Maintenance and Use of Your endless pool .. 25 Draining Your endless pool .. 26 Winterizing Your endless pool .. 26 Poolside Water Quality System Troubleshooting.. 27 Keypad Functions and Troubleshooting.. 2811. Pool Arrival and InspectionThe Standard endless pool arrives in three packages: a skid ofpool panels weighing approximately 850 lbs., a 4' x 8' x 4' highcrate weighing about 1,150 lbs and a pair of 6 5/8" wide steel re-inforcing channels. Most shipping companies will lower the con-tainers to the ground with a hydraulic lift gate on their truck.

6 Thepool can remain in the containers until you are ready to begin in-stallation. Please contact our shipping department prior to ship-ment to answer any questions you may have. Since every deliveryis slightly different, and depends to a large extent on site condi-tions, it is important to speak with our shipping department wellin advance to reduce the chance of surprises. Upon arrival, the packages should be inspected for external dam-age. Should there be visible damage, you must complete a dam-age-claim report provided by the truck driver. Please call theEndless Pools shipping department immediately at (800) 732-8660.

7 The pool components are not damaged by freezing condi-tions and may be stored outside under a tarp for an extendedperiod prior to installation . To begin installation , or to move pool components, begin un-packing the pool. Using a hacksaw or tin snips, remove the steelpacking straps encircling the pool panel skid. The wooden topand sides of the crate may be removed with a phillips-head Site PreparationIt is important that your endless pool be installed over asmooth, level concrete slab that is capable of supporting 260pounds per square foot. The thickness and the quality of the con-crete slab will affect the anchoring method.

8 If you are using the anchor bolt kit or you are installing a Custom Deeper Pool, then the floor must contain no voids orbumps and shall be relatively smooth and level. For customdeeper pools, the walls of the deeper section must also containno voids or bumps. The corners at the depth change should beeased slightly (approx 1/4"). Custom deeper pools must use theAnchor Bolt Kit. Anchoring the pool is discussed in more detaillater in these instructions as well as in a Supplemental Guide. Anoptional Tension Strap and Floor Leveling Kit is available forout-of-level or non-smooth a new slab is poured, consult your local electrical codes regarding grounding and bonding.

9 Many areas require a bonding wire to be attached to the reinforcing bar that is buriedin the should be provided at the pool. It is ideal to install afloor drain in the area just outside of the front pool panel, but notdirectly under the panel or pool itself. In installations where thisis not possible, installation of a secondary containment system tohelp divert water to a more desirable location is call the Customer Service Department if you need any as-sistance in the design of a containment is extremely important to ensure that any water that may reachthe bottom flange of the pool panel, by splashing, run off, or ac-cidental leakage, be drained away immediately.

10 With the bottomflange of the pool panel standing in water, corrosion may occurover is worth the time and effort now to install a drainage systemrather than be unprepared in the event of a Assembly of Pool PanelsProvided with this installation and User s MANUAL will be the ap-propriate panel assembly Supplemental Guide for the Swim Cur-rent that has been Guide will take you through assembling the panels, anchoringthe panels, and drilling the appropriate holes into the panels. It iscritical that this Guide be referenced at this point. Any requiredhole must be drilled before proceeding with the Options An endless pool is usually customized to meet the needs of theend user.