Transcription of INSTRUCTIONS--PARTS LIST 309272C AirAtomizerKit
1 INSTRUCTIONS--PARTS LIST309272 CImportant Safety InstructionsRead all warnings and instructions in thismanual. Save these use with Mark IV, Mark V and GMax 5900 HDTexture SprayersExternal Miix Air Cap: 3300 psi ( bar, MPa) Maximum Working Pressure -- Fluid/Texture MaterialInternal Miix Air Cap: 800 psi (55 bar, MPa) Maximum Working Pressure -- Fluid/Texture Material120 psi (8 bar, MPa) Maximum Working Pressure -- AirModel 244223, Series A-- without air hoseModel 244052, Series A-- with air hoseSKIN INJECTION HAZARDS pray from leaks or ruptured components can inject fluid into your body and cause extremely seri-ous injury, including the need for amputation. Fluid splashed in the eyes or on the skin can alsocause serious injected into the skin may look like just a cut, but it is a serious immediate surgi-cal not stop or deflect leaks with your hand, body, glove or thePressure Relief Procedurebelow before cleaning, checking or servicing the all fluid connections before operating the the hoses, tubes, and couplings daily.
2 Replace worn or damaged parts immediately. Donot repair high pressure couplings; you must replace the entire hoses must have spring guards on both ends, to help protect them from rupture caused bykinks or bends near the not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents orfluids containing such solvents in pressurized aluminum equipment. Such use could result in achemical reaction, with the possibility of Relief Procedure1. Lock gun safety Turn ON/OFF switch to OFF and pressure controlknob to minimum (zero).3. Unplug power supply cord or shut off Unlock gun safety latch. Hold metal part of gunfirmly to grounded metal pail. Trigger gun to Lock gun safety Open pressure drain valve. Leave pressure drainvalve open until ready to spray suspected that spray tip or hose is completelyclogged, or that pressure has not been fully relievedafter following steps above, VERY SLOWLY loosen tipguard retaining nut or hose end coupling to relievepressure gradually, then loosen completely.
3 Now cleartip or hose INC. BOX1441 MINNEAPOLIS, MN 55440--1441 ECOPYRIGHT 2001, GRACO Inc. is registered to EN ISO 90012 309272 Installation1. Fig. 1. Remove two existing screws (F) from spraygun Install air atomizer assembly onto gun handlebracket with two screws (F)3. Remove air hose (P) from fitting (R). Push in onfitting and pull out on air Install air atomizer head (D) to spray gun (B).5. Push air tube (P) into 90_swivel elbows (R)and (K).ti7445ati7436aDFBEKFig. 1 PRAB ACti0622 BTexture Spray GunFlex Spray GunDFBEPRAB ACKC hanging Material Tip and Air CapThe air atomizer head (D) comes with the internal mix cap and spray tip (T, S, A) installed. The external mix aircaps (AB) and (AC) may also be Replace cap (T), material tip (S) and o-ring (A)with air cap (AB) or (AC).
4 2. Fig. 3. Loosen locking cap (U).3. Slide the atomizer assembly (D) to the desiredposition. SeeOperationand table, page Tighten locking cap (U).DSTUAABACti7453aFig. 2AC3092723 OperationPosition air atomizer head as suggested in table. Start with low air pressures and increase until the desired dropletsize is attained. Choose an air compressor capable of supplying 15 cfm @ 90 psi ( bar, MPa) air MixAir CapDropletSizeAA = Approximate Dimension in inches (mm) from Air Cap to End of StemLarge3/4(19)ASmall3/4(19)ti7372aInte rnal MixAir CapPosition Stem End in Approximate Middle of Air Atomizer Headti7437aNo AirMaiximum Airti7446aFinishAir Cap SelectionAir SettingAppearanceOrange PeelInternal MixHighSplatter CoatExternal Mix -- 8-HoleMediumKnock DownExternal Mix -- 4-HoleLow4 309272F12141110213B389419657252123161514 51727ti7435aFig.
5 3111 Texture Spray GunKit 2417052 Needle ValveKit 1127793 Air supply, 3/8 nptAirAtomizerKit4 Included with kit 244052 only5 Included with kit 244223 part No. part No. , assembly13196815 CAP, locking14196816 BODY, air, ring15196817 CAP, air, 4--hole16196818 CAP, air, tip17196819 CAP, air, 8--hole18116170 FERRULE19C20179 O--RING110112781 ELBOW, swivel, 90 111191191 HOSE, air112112782 ELBOW, swivel, 90 113112779 VALVE, needle114100176 BUSHING, hex115190456 BRACKET, valve, air116237821 BRACKET, handle, gun117112775 HOSE, air, cpld, 3/8 in. x 50 ft119116190 TIP, spray121176167 GASKET123116308 RING, retaining, exT125101956 BALL, bearing127169967 FITTING, line, air1 YReplacement Danger and Warning labels, tags andcards are available at no Phone NumberTOPLACEANORDER, contact your Graco distributor, or call1--800--690--2894 Toll Freeto identify your nearest Headquarters:MinneapolisInternational Offices:Belgium, Korea, China, JapanGRACO INC.
6 BOX1441 MINNEAPOLIS, MN 55440--1441 IN 309272 01/2001, Revised 08/2009
