INT Int. Service(+49) 6838/907 172 - Slide Gates, …

1 T V Rheinlandgepr fteSicherheitInstructions Garage Door Operator Model liftmaster 1000 AGBINTInt. Service(+49) 6838/907 172 Failure to comply with the following instructions may result in serious personal injury orproperty damage. Read these instructions carefully The garage door opener is designed and tested to offer reasonable safe service pro-vided it is installed and operated in strict accordance with the instructions in safety alert symbols mean Warning a personal safety or property damageinstruction. Read these instructions : If your garage has no service entrance door, Model 1702E Outside Quick Release must be accessory allows manual operation of the garage door from outside in case of power garage door not letthe garage door opener compensate fora binding or sticking garage or binding doors must berepaired.

2 Garage doors, door springs,cables, pulleys, brackets and their hard-ware are under extreme tension and cancause serious personal injury. Do not attempt to loose, move oradjust for garage door not wear rings, watches or looseclothingwhile installing or servicing agarage door avoid serious personal injury fromentanglement, remove all ropes con-nected to the garage door beforeinstalling the door and wiring must be in compli-ance with your local building and electri-cal codes. Connect the power supplycord only to properly earthed mains. Lightweight doors of fiberglass, alu-minum or steel must be substantiallyreinforced to avoid door damage. (Seepage 6.) The best solution is to checkwith your garage door manufacturer foran opener installation reinforcement safety reverse system test is garage door MUST reverse on contact with a 40mm obstacleplaced on the floor.

3 Failure to properlyadjust the opener may result in seriouspersonal injury from a closing the test once a monthand make any needed unit should not be installed in adamp or wet must not extend over publicbyway during by Reading These Important Safety InstructionsThe Protector System must beinstalled when the force at the edge ofthe closing door force exceeds 400N(40kg).Excessive force will interfere withthe proper operation of the SafetyReverse System or damage the garage door. Permanently fasten thecaution labeladjacent to the wall-mounted door controlcontrol button as a reminder of safe oper-ating all existing garage doorlocksto avoid damage to garage the lighted door control button (orany additional push buttons)in a locationwhere the garage door is visible, at aheight of at least and out of thereach of children.

4 Do not allow chil-dren to operate push button(s) orremote control(s).Serious personalinjury from a closing garage door mayresult from misuse of the opener only when the door isin full view, free of obstructions andopener is properly adjusted. No oneshould enter or leave the garage whilethe door is in motion. Do not allowchildren to play near the manual releaseonlyto disengagethe trolley and, if possible, onlywhen thedoor is not use the red han-dle to pull the door open or electric power to thegarage door opener before makingrepairs or removing product is provided with a powersupply cord of special design which, ifdamaged, must be replaced by a powersupply cord of the same type; such apower supply cord may be obtained andfitted by a RULES.

5 1 DOOR TYPES ..2 TOOLS REQUIRED ..2 HARDWARE PROVIDED ..2 BEFORE YOU BEGIN ..3 COMPLETED INSTALLATION ..3 ASSEMBLY ..3-4 INSTALLATION ..4-5 CONNECT ELECTRIC POWER ..6-7 PROGRAMMING THE CODE ..8-9 ADJUSTMENT ..10 CONTENTSPAGEINSTALL THE PROTECTOR SYSTEM (OPTIONAL) ..11 SPECIAL FEATURES ..11 ACCESSORIES ..11 REPLACEMENT PARTS ..12-13 CARE OF YOUR OPENER ..13 MAINTENANCE OF YOUR OPENER ..13 HAVING A PROBLEM? .. 14 OPERATION OF YOUR OPENER ..15 SPECIFICATIONS ..151-GBTOOLS REQUIRED Door with Horizontal Track Only Door with Horizontal and VerticalTrack Special door arm (E, TheChamberlain Arm ) and The ProtectorSystem (29 (9)) are required. See your Door with Curved Track See 20B connect door arm. The Protector System(29 (9) is required for doors that are over door Special door arm (E, TheChamberlain Arm )and The ProtectorSystem (29 (9)) are required.)

6 See your Chamberlain Arm for use on door typesB and D. DOOR TYPESHARDWARE PROVIDED (1)Hex Bolt(2)Clevis Pin (3)8mm Carriage Bolt (4)Wood Screws (5)Sheet Metal Screws (6)Clevis Pin (7)Rope(8)Handle(9)Insulated Staples (10)Anchor(11)Concrete Anchor (12)Lock Washer (13)Hex Nut (14)Ring Fastener (15)Hex Bolt(16)Nut(17)Metric Tapping Screw (18)Hex Screw (19)Stop Bolt ABEDC1079345612138 NOTICE11151417181(2x)16192(2x)(2x)(2x)(2 x)(2x)(1x)(1x)(1x)(4x)(4x)(4x)(4x)(5x)(5 x)(3x)(10x)(2x)(2x)2111mm, 13mm11/13mm10mm, 8mm, 4,5mm, 4mm13 ASSEMBLY SECTIONIMPORTANT: If you have a canopy door, you need to use the instructions packed with The ChamberlainArm Accessory in conjunction with this Owner's Manual when assembling the Installation As you proceed with the assembly, installation and adjustment procedures in this manual, you may find it helpfulto refer back to this illustration of a completed YOU BEGIN:1.

7 Look at the wall or ceiling above the garage door. The header bracket mustbe securely fastened to Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (notsupplied) may be Depending on your door's construction, you might need a special door arm. See your Do you have an access door in addition to the garage door? If not, Model 1702E Outside Quick ReleaseAccessory is required. This accessory allows manual operation of the garage door from outside in case ofpower failure.(1)Header Sleeve(2)Idler Pulley Bracket(3)Trolley(4)Rail(5)Chain/Belt(6) Hanging Bracket(7)Power Cord(8)Opener(9)Light Lens(10)Manual Release Rope & Handle(11) Curved Door Arm(12)Straight Door Arm(13)Door Bracket and Plate(14)Header Bracket(15)Trolley Release Arm3-GBInstall the Chain/BeltRemove chain/belt from carton and lay chain out onfloor (do not allow chain/belt to twist).

8 A. Chain:Push pins of master link bar (3) throughchain link (4) and hole in trolley (5). Push cap (2)over pins and onto notches. Slide clip-on spring (1)over cap and onto pin notches until both pins aresecurely locked in Belt: Hook the trolley connector (6) into the slot (7)on the trolley (8).Insert Chain/Belt into Rail & AssembleHeader SleeveSlide pulley bracket (1) and inner trolley (2) into back(opener end) of rail assembly (3), be sure to insertpulley bracket as shown with arrow (4) pointingtoward front (header end) of rail (5). Push brackettoward front (header end ) of rail (5). Insert carriagebolt (6) through header sleeve bracket (7). Looselythread spring nut (8) and flat washer (9) onto carriagebolt.

9 Insert carriage bolt (6) of header sleeve assem-bly (7) into bold cut out in pulley bracket (1). Slideheader sleeve assembly (7) on to front (header end)of rail (10).Attach Trolley to RailSlide outer trolley (1) into back (opener) end of the railassembly (2), be sure end with trolley release arm (3)is heading in direction of opener. Slide outer trolleydown rail until it engages with inner 54312A-1 543124531287691016710132687 Assemble the RailGrease inside edges of rail sections using grease (1).Place rail pieces (2) on flat surface for assembly. Allfour rail sections are interchangeable. Slide rail brace(3) onto rail section. Connect rail by sliding rail braceonto next rail section. Tap rail assembly (4) on pieceof wood (5) until rail sections are flush.

10 Repeat withremaining rail Header SleeveThread spring nut on carriage bolt until finger a screwdriver tip (1) into one of the slots of thenut ring (2) and brace it firmly against the headersleeve. Place an open end wrench (3) on the squareend of the spring nut (4), slightly rotate nut about 1/4turn clockwise until nut ring (2) is released againstheader sleeve (5). This sets spring to optimum chaintension. Chain may slip off sprocket if chain/belt is tooloose. If chain does slip re-tighten spring nut by turingnut clockwise 1/2 turn. Do NOT Rail to Opener and InstallChain/BeltHolding chain (4) and belt (5) out of the way, Slide rail(1) onto shim (2) until rail is secure. Take thechain/belt and wrap it around the sprocket (3).