INTELI•TOUCH DUAL W-32 INSTALLATION - …

1 casablanca Fan Co. - Factory Service Department - Technical Library38 inteli touch dual W-32 INSTALLATIONCAUTION! Ensure power is turned OFF at the breakeror fuse panel before starting Determine which wire is connected to the common terminal of the 3-way switch. (Theterminal will be marked on switch).2. Remove the wire from the common terminal of the 3-way switch. Connect this wire to theremaining black/white striped wire on the W-32 control. Secure this splice with a wire Remove the two remaining wires from the 3-way switch. Connect one of these wires to ablack wire on the W-32 control. Secure the splice with a wire nut. The remaining wire is tobe connected to the other black wire on the W-32.

2 Secure the splice with a wire Install the W-32 in the wall box with the two long screws Install the wall plate with the two short color-matched screws INSTALLATION of the second W-32 control is identical. Repeat steps 1 through Control Replacement - CONTINUEDC asablanca Fan Co. - Factory Service Department - Technical Library39 inteli - touch ControlsINTELI touch W-32 INSTALLATIONL ocate the BLUE wire that is wire nutted to BLACKWIRE WITH THE WHITE STRIPE as shown, removethe wire nut. Now locate the BLACK HOT WIRE that isattached to the other BLACK WIRE WITH THE WHITESTRIPE wire, also remove the wire nut. Switch the wireas shown and wire nut them YOUR WORK:NOTE: If your wall control operationis reversed, , fan switch controlslights and light switch controls fan,simply swap the two W-32 black/white stripe inteli - touch control makes possible the remote control of all ceiling fan and light functions from one or twoconvenient wall locations.

3 At the heart of the inteli - touch control is a microprocessor located within the fan housing. Thisunit decodes and stores the commands sent from the wall controller (W-32 and W-33). The wall control takes the place ofthe conventional wall switch and eliminates pull chains, switches and knobs from the fan & W-33 Controls1992 - CurrentThe W-32 and W-33 sends the same commands asthe original controllers, but was modified to provide a singlebutton for Reverse, and a recessed Power button to avoidaccidentally turn off the power to the fan. Both the W-32 andW-32 can be used as a wall control for the inteli - touch W-11/W-12 were the original controls for theInteli touch line.

4 The W-11 allowed single wall control ofone fan, while the W-12 permitted two controls to operateone fan. Reverse is accomplished by pressing the FANand LIGHT buttons simultaneously. Note the W-11 and W-12 SHOULD NOT be used to operate the newer Control Replacement - CONTINUEDW-11 & W-12 Controls(Original I T Fans)1983 - 1992 casablanca Fan Co. - Factory Service Department - Technical Library40W-32 is used to describe either White or Ivory Remove the screws and switch plate from the existing Remove the screws holding the switch in the switch Pull the existing switch from the switch box to expose the Remove the two wires from the Connect the two wires just removed from the switch to the W-32wall control black wire and black/white stripe wire.

5 Secure theseconnections with wire Install the W-32 in the wall box with the two long screws Install the wall plate with the two color matched ! Ensure power is turned OFF at the breaker or fusepanel before starting : If your wall control operation is reversed, , fanswitch controls lights and light switch controls fan, simplyswap the two W-32 black/white stripe the BLUE wire that is wire nutted to BLACKWIRE WITH THE WHITE STRIPE as shown,remove the wire nut. Now locate the BLACK HOTWIRE that is attached to the other BLACK WIREWITH THE WHITE STRIPE wire, also remove thewire nut. Switch the wire as shown and wire nutthem YOUR WORK:NOTE: If your wall control operation isreversed, , fan switch controls lightsand light switch controls fan, simplyswap the two W-32 black/white touch SINGLE W-32 InstallationWall Control Replacement - CONTINUEDC asablanca Fan Co.

6 - Factory Service Department - Technical Library41 inteli - touch W-32 Wall Control INSTALLATION (3-Way INSTALLATION Instructions)THREE WAY - INSTALLATION InstructionsSAFETY FIRST:1. Turn off power at its source (fuse or circuit breaker)Turn OFF power at its sourceCircuit Breaker Box Fuse BoxIf you want to be able to turn an inteli - touch on and off at two location, such as at the top and the bottom of astair case or at either end of a dinning room, consider installing a pair of W-32 switches in a three-waylocation.( Figure #1)Wall Control Replacement - CONTINUEDWall Control Replacement - CONTINUEDC asablanca Fan Co. - Factory Service Department - Technical Library422.

7 Remove the switch plates from both wall switches Loosen the three screws on the switch, remove the twotraveler wires from the top of the switch and the hot wirefrom the bottom of the switch as shown in (Figure #4)( Figure #4)( Figure #5)4. Do the same on switch number 2 as shown in (Figure#5). inteli - touch W-32 Wall Control INSTALLATION (3-Way INSTALLATION Instructions)Wall Control Replacement - CONTINUEDWall Control Replacement - CONTINUEDC asablanca Fan Co. - Factory Service Department - Technical Library43 inteli - touch W-32 Wall Control INSTALLATION (3-Way INSTALLATION Instructions)( Figure #6)Once both toggle switches have been removed, itis time to install the W-32 Wall Locate the BLACK WITH WHITE STRIPE wires asshown in (Figure #7).

8 They will be located on the back ofthe W-32, DO NOT use the black with white stripe wire,that is wire nutted to the blue wire. Connected the blackwith white stripe wire from the top of the back of the W-32to the HOT wire coming from the power source. Alsoshown in (Figure #7).6. Locate the TWO (2) BLACK wires located at bottomand back of W-32 as shown in (Figure #8). Connect thesetwo wires to the TRAVELER WIRES also shown in (Figure#8).Wall Control Replacement - CONTINUEDWall Control Replacement - CONTINUED( Figure #7)( Figure #8) casablanca Fan Co. - Factory Service Department - Technical Library44 inteli - touch W-32 Wall Control INSTALLATION (3-Way INSTALLATION Instructions)( Figure #6)( Figure #10)Once both toggle switches have be removed from the wall, it is time to install the W-32 Wall Locate the BLACK WITH WHITE STRIPE wires asshown in (Figure #9).

9 They will be located on the backof the W-32, DO NOT use the black with white stripewire, that is wire nutted to the blue wire. Connect theblack with white stripe wire from the top of the back ofthe W-32 to the HOT wire. Also shown in (Figure #9).8. Locate the TWO (2) BLACK wires located at bottomand back of W-32 as shown in (Figure #10). Connectthese two wires to the TRAVELER WIRES also shownin (Figure #10)NOTE: - DO NOT install the switches in wall until aftertesting. If the light button operates the fan and the fanoperates the lights you will have to make changes tothe wiring as shown in (Figure #12).Wall Control Replacement - CONTINUEDWall Control Replacement - CONTINUED( Figure #9) casablanca Fan Co.

10 - Factory Service Department - Technical Library45 inteli - touch W-32 Wall Control INSTALLATION (3-Way INSTALLATION Instructions) inteli - touch Series ( Wall Control Testing)( Figure #11)( Figure #12A)( Figure #12B)10. If the light button operates the fan button and the fan operates the lights you will have to make changes to thewiring as shown in (Figure #12A and B).Locate the BLUE wire that is wire nutted to BLACK WIRE WITH THE WHITE STRIPE in (figure #12A), removethe wire nut. Now locate the BLACK HOT WIRE that is attached to the other BLACK WIRE WITH THE WHITESTRIPE wire, also remove the wire nut. Swap the wires as shown in ( Figure #12B ) and wire nut themtogether. If operation is still reversed, rewire the first control as it was and change the wires on switch Control Replacement - CONTINUEDWall Control Replacement - CONTINUEDC asablanca Fan Co.