Example: bachelor of science

Interior A Assembly F ENGLISH W K L M B Installation and ...

66071-001. Rev 01. Z-Wave Plus Parts in the box Latch Exterior Interior Assembly Assembly A. ENGLISH . F. W K L M. B. Installation and User guide B is not included. If needed, Mounting Fasteners please contact Kwikset to order Plate a drive-in latch for your lock. 03809 46780. Strike Adapter G N Q. Required tools ring P S. Kwikset C D. 4 AA Batteries Ruler Phillips head screwdriver Technical Support SmartKey Tool 48654 27526 64109. Additional Tools (depending on application) 1-866-863-6584 Keys T. H U V. E. Hammer Wood block 1 Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at A Measure to confirm that the hole in B Measure to confirm that the backset is C Measure to confirm that the hole in D Measure to confirm that the door is the door is either 2-1/8" (54 mm) or either 2-3/8" or 2-3/4" (60 or 70 mm).

and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com. 2x One green flash with one beep* Three red flashes with three beeps* Two beeps* or or Programming time out. Make sure not to pause for more than 5 seconds during programming. Tip: You can press the Lock button before entering your user code to light up the keypad at night.

Tags:

  Guide

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Interior A Assembly F ENGLISH W K L M B Installation and ...

1 66071-001. Rev 01. Z-Wave Plus Parts in the box Latch Exterior Interior Assembly Assembly A. ENGLISH . F. W K L M. B. Installation and User guide B is not included. If needed, Mounting Fasteners please contact Kwikset to order Plate a drive-in latch for your lock. 03809 46780. Strike Adapter G N Q. Required tools ring P S. Kwikset C D. 4 AA Batteries Ruler Phillips head screwdriver Technical Support SmartKey Tool 48654 27526 64109. Additional Tools (depending on application) 1-866-863-6584 Keys T. H U V. E. Hammer Wood block 1 Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at A Measure to confirm that the hole in B Measure to confirm that the backset is C Measure to confirm that the hole in D Measure to confirm that the door is the door is either 2-1/8" (54 mm) or either 2-3/8" or 2-3/4" (60 or 70 mm).

2 The door edge is 1" (25 mm). between 1-3/8" and 1-3/4"* (35 mm 1-1/2" (38 mm). and 44 mm*) thick. ba 2-3/8" or 2-3/4" ck se 60 or 70 mm t 1-3/8" 1-3/4"*. 2-1/8" 35 44 mm*. 54 mm 1". or 25 mm 1-1/2". 38 mm Note: Additional door preparation may be *Service kits for 2-1/4" (57 mm) thick doors required for doors with 1-1/2" (38 mm) holes. are available through Kwikset. Consult the deadbolt drilling instructions at actual 2 Install the latch and strike size N P Q. S. A Is the door edge chiseled? B Hold the latch in front of the door hole, with the latch D Which latch are you installing? face flush against the door edge. YES NO Latch A Latch B . or chiseled or not chiseled B. Use latch A . If the Use latch B (not A B. latch bolt is not already included). If the latch extended, extend the bolt is not already latch bolt as shown. extended, extend the latch bolt as shown.

3 A B A. C Is the D-shaped hole centered in the door hole? YES NO. N or P. (2x) wood block or D-shaped hole D-shaped hole No adjustment is required. Rotate latch face as Proceed to next step. shown to extend latch. A E Install strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. Longer screws install closest to the door jamb. B. S (2x) C. Q (2x) door frame 1/4. actual 3 Install the exterior keypad size T. A Insert cylinder into keypad. C Install exterior keypad and mounting plate. F a b c Support exterior Assembly during mounting plate Installation . Locate screws and keep them W within reach. G. F. B What is the diameter of the hole in the door? Diameter is 2-1/8" Diameter is 1-1/2" Cable goes Route cable through T underneath latch. (54 mm) (38 mm) center hole, then push cable into side hole. or 2-1/8" 1-1/2" d e Keep parallel to 54 mm 38 mm edge of door.

4 E. Insert key and test latch. If latch D is required for Installation . D is not needed for does not extend or Install D on F . Installation . Discard D . retract smoothly, T adjust screws (T). F D. T (2x) Remove key when finished and make D Tighten sure the latch bolt screws evenly. is fully extended. 4 Install the Interior Assembly actual size U. A Remove battery cover. B Remove battery pack. C Make sure the turnpiece is in the vertical position. K. M. L. Do not install batteries until step 5. L vertical D Connect cable. Ensure tight cable E Lay cable flat against the Interior F Push turnpiece shaft onto G Secure Interior Assembly with connection. housing. torque blade. supplied screws. L. U (2x). Note: Turnpiece may not rotate torque turnpiece smoothly until blade shaft after step 5. 5 Install the batteries and perform the door handing process This step will teach your lock the orientation of your door and is crucial to lock operation.

5 A Install 4 AA batteries in battery pack. B Press and HOLD the Lock button C Did the latch bolt retract and extend on its while installing battery pack. own when the battery pack was installed? Hold button until the latch bolt starts moving on its own. K. YES NO. or Ensure correct polarity. Door handing process Remove battery For best results, use was successful! Proceed pack, wait 15 seconds, new, non-rechargeable to next step after latch then attempt the Alkaline batteries only. bolt stops moving. process again. 2/4. 6 Add the lock to your smart home system A Initiate the process to add B When prompted by your smart home system to add the C If successful, re-name the lock in your system the lock to your system at lock, press button A on the lock Interior one time. The (if applicable). your smart home controller. red LED will illuminate when the lock enters Add Mode.

6 Refer to your smart home system instructions for more information. button A D If unsuccessful, follow your system's instructions to remove the lock from the controller and any other network, then press button A on the lock one time. Perform steps 6A-6C again. If still unsuccessful, consult the Programming and Troubleshooting guide on the SmartCode 916 page Please allow time for the controller to add the lock. at 7 Add user codes (30 max). It is recommended that you add and A Make sure the door is open. Press B Enter user code. A total of 30 user C Press Lock button once. delete all user codes through your smart the Program button the number of codes may be programmed. home control system. If your system times that corresponds to the user does not allow this, codes may be added directly to the lock as shown here. code position being programmed. Programming Timeout Example: If If no button is pressed for five seconds, Each user code programming must be a unique the system will time out and you will need the third code, to restart the procedure.

7 Code between press the button 4 and 8 digits, three times. depending on your smart home system. D What lights and sounds does the lock produce? One green flash with one beep* Three red flashes with three beeps* Two beeps*. or or green red 2x 1x 3x Programming was successful. Programming was unsuccessful. Programming time out. Make sure the user code is not a duplicate and that it is Make sure not to pause for more between 4 and 8 digits during your next attempt. than 5 seconds during programming. *Beeping sound will only be heard if switch #3 (on the lock Interior ) is in the on positon. See Switches and Status LED Colors on page 4. Mastercode For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting guide on the SmartCode 910 page at 8 Test the lock (review normal operation).

8 Confirm that the code(s) added in previous step can unlock the door. Locking the Door Unlocking the Door Press Lock button once. Enter user code. Tip: You can press the Lock button before entering your user code to light up the keypad at night. 9 Re-key the lock (if needed) and install the battery cover actual size V. A Re-key the lock (if needed). B Install the battery cover. a c K a K b b IMPORTANT: Re-key the lock Reinstall Remove to work with battery M. battery your existing key. pack. pack before See the supplied re-keying. SmartKey Re-key V (3x). instructions for more H. information. 3/4. Reference guide SmartCode at a Glance System Alerts Alert Reason Solution Keypad flashes red 1 time Door jammed while Manually re-lock door. If needed, Exterior Interior (cover removed) with 1 beep* attempting to lock. reposition strike. Attempt programming procedure Unsuccessful programming.

9 Again. Back Keypad flashes red 3 times panel with 3 beeps* One incorrect code entered. Re-enter code. Button A Button B . No user code programmed. Program at least one user code. Keypad flashes red 10. Keypad Low battery. Replace batteries. Program times with 10 beeps*. Lock button Switches button Lock beeps 2 times. Status Attempt programming procedure Keypad flashes red 3 times. LED Programming timeout. again, making sure not to pause for SmartKey Keyway more than 5 seconds. Turnpiece Keypad flashes red 6 times tool hole with 6 beeps*. Keypad flashes red 15 times Three incorrect codes entered Re-enter code after 60 second keypad with 15 beeps* within one minute. lockout. *Beeping sound will only be heard if switch #3 is on. Switches and Status LED colors Troubleshooting Switches On Off Status LED. 1 2 3 4 A complete Programming and Troubleshooting guide is available on the SmartCode 910 page at Switch Function Color Lock Status Door lock status LED blinks every 6 Blinking green Unlocked 1.

10 Seconds Blinking amber Locked Lock automatically re-locks door 30 Blinking red Low battery 2 seconds after unlocking. Disabled if no codes are programmed. Door handing process did not work properly. 3 Audio Solid red See the online Programing and 4 Not used. Troubleshooting guide . Deleting a user code Factory Reset In order to delete a user code, you must override the code by adding a different user code in the same A factory reset will delete all codes associated with the lock, position. For example, if you want to delete the third code, add a different user code in position three. and it will remove it from your smart home system. Test the old user code to make sure it can no longer unlock the door. 1 Remove 2 Press and HOLD the Program battery pack. button while reinserting If you cannot remember the user code position, you may wish to perform a factory reset to delete all the battery pack.


Related search queries