ISO 9001:2008 CERTIFIED Magnetic Liquid-Level …

1 Magnetic Liquid-Level Gauges for LP Gas ServiceISO 9001:2008 CERTIFIED6200 The Measure of ExcellenceSee reverse side for dimensional data, materials of construction, performance, and advice on how to gauges are supplied standard with 0015-00007 Buna-N gasket and four0040-00414 zinc-plated steel mounting bolts (1 4" 28 x 7 8") for attachment to agauge adapter with " [51,5] diameter bolt circle (see installation instructionsMS-501/502).Models 6281 and 6284 Junior gauges used on above ground ASME storagetanks are equipped with R3D Remote Ready 5909S02733 percentage 6281 Jun ior gauges used on below ground ASME storage tanks areequipped with R3D Remote Ready 5909S02799 per cent age dials. Mod els6241 and 6244 Junior gauges used on ASME motor fuel tanks come with theoption of direct read, TwinSite , or Hall Effect dials. All gauges in the 6240 series and B6240 se ries incorporate a stronger mag net nec es sary to drive remote read ing TwinSite send ers in mo tor fuel ap pli ca tions.

2 All Senior gauges except models 6290 and 6293 come equipped with 0015-00004 Buna-N gas kets and four 0040-00415 zinc plated steel mount ing bolts,(5 16" 24 x 7 8"), for at tach ment to a gauge adapter with " [63,5] diameter boltcircle (see Roch es ter Adapt er Ma chin ing Standard MS-502). Model 6280 and6283 Senior gauges used on above ground ASME storage tanks are equippedwith direct-reading 5001S00001 per cent age di 6290 and 6293 Senior gauges with stainless steel heads may be usedon above ground hor i zon tal or ver ti cal ASME stor age tanks over 3500 [13250liters] gallon capacity and are equipped with cap bolts, teflon-filled, stainlesssteel gas kets, stronger magnets and direct-reading 4" diameter per cent agedials. Tank draw ings must be fur nished for all ver ti cal tanks so we can recom-mend com put er gen er at ed gauge adapter place ment to cor re spond with an as -sort ment of standard dials and dial sets calibrated for vertical top mounting, includes standardmagnet to drive direct-reading as 6281, except for side,end, or angle top mounting, includes strongermagnet to drive TwinSite side, end, or angle mounting,otherwise same as as 6244, exceptwith brass top mounting, includes standardmagnet to drive direct-reading as 6280, except for side,end, or angle top mounting, includes strongermagnet to drive large 4 as 6290, except for side,end, or angle Measure of Excellence11616 Harry Hines Blvd.

3 Box 29242 Dallas, TX 75229 (972) 241-2161 FAX(972) 620-3374 Liquid-Level Gauges for LP Gas Service* Materials and specifications are subject to change with out notice. Pressure ratings sub ject to change due to tem per a ture and other en vi ron men tal 1 2-14 B75 Materials of Construction*HeadAluminum die casting stan dard. Mod el B6244 has brasshead, mod els 6290 and 6293 have stainless steel HousingAluminum die-casting or Bearings, Gear, Pinion, CrossStud & Bear ing, & Dial ScrewsStainless , Centershaft & Float RodTempered alu mi BulbNitrile rubber or one piece alu mi standard. Spiral wound, teflon-filled, stainless steelon models 6290 and BoltsZinc-plated steel, stainless steel Direct Reading Dials & TwinSite SendersUltrasonically sealed DialsAluminum with acrylic or polycarbonate crystal, sealed withrubber " DialsAluminum with glass crystal, sealed with a rub ber Specifications*Temperature RangeStandard range is -40 F to 176 F, -40 C to 80 depends upon proper gauge sizing.

4 Junior andSenior dials 5%, 4 dials 4%, TwinSite dials 8%. Halldial output 4% of visual reading. Accuracy may be lessdepending upon tank shape. Accuracy may be less nearfull and empty. Accuracy may be less if tank is not may be less due to variations in liquid tempera-ture. This gauge is not to be used for filling. All accuracyestimates are expressed as percent of full high humidity below ground or under chassis ap pli ca -tions, brass, stainless steel, or painted alu mi num heads & VibrationSuitable for mobile service watts maximum dissipation for TwinSite Pressure375 psi. [25,8 Bar]ApprovalsGauges are UL listed for LP Gas service ordering, head size, Junior or Senior, or model #. diameter as shown on nameplate. location (top, side, end or angle). gauge is angle mounted, state gauge is end mounted, state the shape of the tankhead, hemispherical or H dimension (the distance in inches from the sur-face of the tank to the gasket surface on the riser).

5 To order replacement gauge , simply furnish the in for ma tionstamped on one of the flat sections on the side of the gaugehead as shown in the :For installation instructions see MS-501 number = 6244 Support length = 7 1 2 Tank diameter = 14 Mfg. date = B75 Note: gauge head may also be stamped with model &unique suf fix #.