KMS ShopChartz™ (Tap Drill.slsmn)

FILE IDENTIFICATION CHART - KMS Tools

Double-cut top and bottom. One safe edge and one single-cut edge. Bastard, second and smooth cuts. For removing metal on sharp corners, shoulders and flat surfaces. 4" – 12" long. Knife File — Triangular cross section. Tapered. Double-cut top and bottom. One safe edge and one single-cut edge. Safe back. Bastard, second and smooth cuts.

  Edges, Knife

TAP AND DIE CHART - FREE TECHNICAL CHARTS

drill this size hole: tap & die chart tap & die chart drill this size hole totapforthissize bolt or screw: 14m - 1.50 ptdl 14m-1.25 pitch 9/16-18

  Chart, Tap and die chart, Die chart tap, Die chart

Metric Tap Size Chart - FREE TECHNICAL CHARTS

Metric Tap Size Chart Tap size Diameter (in) Diameter (mm) Thread count (TPI) Thread pitch (mm) Tap drill size M1x0.2 0.0394 1.0000 ~127 0.200 0.8 mm

  Chart, Size, Metrics, Metric tap size chart, Metric tap size chart tap

Tapping Drill Char T 339 - Construction Supply

Tapping Drill Char T UNC Unified National Coarse ... TAp mETAL OR pLAsTIc • Secure workpiece and drill hole using correct size tapping drill as shown on this chart. • Select suitable lubricant – see chart below. • Secure tap in wrench and place tap squarely in hole.

  Chart, Drill, Tapping, Arch, Tapping drill char t

Tap Drill Chart - Fasteners Inc.

Tap Drill Chart (Metric H6) Tap Size Cut Tap Drill Roll Tap Drill Minor Ø Major Ø ...

  Chart, Drill, Tap drill chart

Tools and Dies - TNB.COM

The catalog numbers shown in the chart above are for the upper half of the die. For the bottom half (the indenter), order one Cat. No. 6TONX for all 6TONX Series, one Cat. No. TBM62X for all TBM62X Series Die Codes 21X–66X, ... Tools and Dies — ...

  Chart, Tool, Edis, Tools and dies

Compression Connector System - TNB.COM

Compression Connector System. Step One Preparing the Cable ... Main Branch 1 Branch 2 Branch 3 H-Tap Color Die Tool # Of Crimps Die Embossing Strip Length Insulating Cover 8-14 (8-14) 8-14 (8-14) - - CHT814-10 Green 15CA37RCH* Group 1 1 37R 1/2" HTC2S ... Tool and Die Chart for Standard C-Taps

  Chart, System, Connectors, Compression, Compression connector system, And die chart

tap & die charts - Avon Engineering Supplies Christchurch

169A Wordsworth St P.O. Box 22-066 Christchurch ENGINEERING SUPPLIES LIMITED www.avontools.co.nz Phone (03) 366 5190 Fax (03) 961 4899 tool@avontools.co.nz

BURNDY Products Reference TABLE OF CONTENTS

BURNDY ® Products Reference ... Die Set Conversion Chart (Obsolete Dies) ... If moisture does penetrate the tap-ing, it will not dry out as readily as if the joint were untaped. Various plastic materials are available today for covering low voltage con-nections or for bare conductor connections

  Chart, Burndy

UNJ Thread Taps - Guhring, Inc.

Series 1059 through holes Standard DIN 2184-1 TiCN coated Standard DIN 371 external cooling Tool Material HSS-E PM Flute Spiral Point Chamfer Form B (3.5 - 5) Class of Fit 3BX Cutting Direction right-hand Series 1060

  Thread, Pats, Unj thread taps

REFERENCE TABLES - Union Millwright

REFERENCE TABLES American National and Unified Coarse and Fine Thread Dimensions and Tap Drill Sizes (continued) Threads per inch Outside Pitch Root Tap Drill Decimal

  Reference, Table, Reference tables