LF353-NWide Bandwidth Dual JFET Input Operational Amplifier
• Fast Settling Time to 0.01%: 2 μs input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift. Typical Connection 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
LMC6482 CMOS Dual Rail-To-Rail Input and Output ...
www.ti.comLMC6482 www.ti.com SNOS674E –NOVEMBER 1997–REVISED APRIL 2015 5 Pin Configuration and Functions D, DGK and P Packages 8-Pin SOIC, VSSOP and PDIP (Top View) Pin Functions PIN TYPE DESCRIPTION NO.
LM136-2.5,LM236-2.5,LM336-2 - TI.com
www.ti.comLM136-2.5/LM236-2.5/LM336-2.5V Reference Diode General Description The LM136-2.5/LM236-2.5 and LM336-2.5 integrated cir-cuits are …
SimpleLink™ CC3120, CC3220 Wi-Fi ... - Texas …
www.ti.comUser User x x x x x x x x x x x x x x x x x x x x Application Servers Vendor IoT Devices Internet Introduction www.ti.com 4 SWRA509A–February 2017–Revised March 2017 Submit Documentation Feedback
www.ti.com SNVS749F - Texas Instruments
www.ti.comLM136-2.5-N SNVS749F – MAY 1998– REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Temperature Drift Figure 13. …
MSP430x2xx Family User's Guide (Rev. J) - TI.com
www.ti.comMSP430x2xx Family User's Guide Literature Number: SLAU144J December 2004– Revised July 2013
Guide, User, Family, Msp430x2xx family user s guide, Msp430x2xx
1.8-V Micropower CMOS Operational Amplifier …
www.ti.com5 OPA2333-HT www.ti.com SBOS483I –JULY 2009–REVISED MAY 2015 Product Folder Links: OPA2333-HT Copyright © 2009–2015, Texas Instruments Incorporated Submit Documentation Feedback
Operational, Texas, Texas instruments, Instruments, Cmos, Amplifier, Micropower, Micropower cmos operational amplifier
OPAx354 250-MHz, Rail-to-Rail I/O, CMOS …
www.ti.comOPA354 IN +IN V OUT V+ V Product Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use …
Analog linearization of resistance temperature …
www.ti.com21 Analog Applications Journal Texas Instruments Incorporated 4Q 2011 www.ti.com/aaj High-Performance Analog Products …
Resistance, Temperatures, Texas, Texas instruments, Instruments, Analog, Analog linearization of resistance temperature, Linearization
TMS320C28x DSP/BIOS 5.x Application …
www.ti.comSPRU625L—August 2012 API Functional Overview 9 Submit Documentation Feedback www.ti.com Naming Conventions 1.2 Naming Conventions The format for a DSP/BIOS operation name is a 3- or 4-letter prefix for the module that contains the
WL18x7MOD WiLink™ 8 Dual-Band Industrial …
www.ti.comProduct Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
Related documents
Precision, Very Low Noise, Low Input Bias Current, Wide ...
www.analog.comoutput phase reversal when input voltages exceed the maximum common-mode voltage range. Fast slew rate and great stability with capacitive loads make the AD8510/AD8512/AD8513 a perfect fit for high performance filters. Low input bias currents, low offset, and low noise result in a wide dynamic range of photodiode amplifier circuits. Low
SECTION 4 SWITCHED CAPACITOR VOLTAGE CONVERTERS …
www.analog.comSwitched capacitor voltage converters do not maintain high efficiency for a wide range of ratios of input to output voltages, unlike their switching regulator counterparts. Because the input to output current ratio is scaled according to the basic voltage conversion (i.e., doubled for a doubler, inverted for an inverter)
Ranges, Input, Voltage, Wide, Wide range
ICM7555 General purpose CMOS timer
www.nxp.comn Wide operating supply voltage range guaranteed 3 V to 16 V over full automotive temperatures n Normal reset function; no crowbarring of supply during output transition ... VI input voltage TRIGGER: VDD = 5 V 0.29VDD 0.31VDD 0.34VDD V CONTROL_VOLTAGE: VDD = 5 V 0.62VDD 0.65VDD 0.67VDD V THRESHOLD: ...
LM2576 - 3.0 A, 15 V, Step-Down Switching Regulator
www.onsemi.com• Adjustable Version Output Voltage Range, 1.23 to 37 V ±4% Maximum Over Line and Load Conditions • Guaranteed 3.0 A Output Current • Wide Input Voltage Range • Requires Only 4 External Components • 52 kHz Fixed Frequency Internal Oscillator • TTL Shutdown Capability, Low Power Standby Mode • High Efficiency
Ranges, Input, Voltage, Wide, Wide input voltage range, Voltage range
LM339 - Single Supply Quad Comparators
www.onsemi.com• Low Input Bias Current: 25 nA (Typ) • Low Input Offset Current: ±5.0 nA (Typ) • Low Input Offset Voltage • Input Common Mode Voltage Range to GND • Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA • TTL and CMOS Compatible • ESD Clamps on the Inputs Increase Reliability without Affecting Device Operation
AEROSEMI - Olimex
www.olimex.comInput and Output capacitors should be placed close to the IC and connected to ground plane to reduce noise coupling. The GND should be connected to a strong ground plane for heat sinking and noise protection. Keep the main current traces as possible as short and wide. SW node of DC-DC converter is with high frequency voltage swing.
Analog to Digital Conversion - mccdaq.com
www.mccdaq.cominput of 10 VDC can resolve the measurement into 10 VDC/4096 = 0.00244 VDC = 2.44 mV. Similarly, for the same 0 to 10 VDC range, a 16-bit ADC resolution is 10/216 = 10/65,536 = 0.153 mV. The resolution is usually specified with respect to the full-range reading of the ADC, not with respect to the measured value at any particular instant.
KAAP686 Mathematics and Signal Processing for …
www1.udel.eduApr 27, 2011 · The rectified signal is low pass filtered, with in the 5 – 100 Hz range, and the result looks like the “envelope” of the original signal. One way to low pass filter a signal is to simply take the mean value, in a window which “slides” along the signal. Some authors advocate this “rectify and mean” approach. Such a moving–average