Lifting Capacities - Hatton Crane & Rigging

1 Litho in 12/00 1 #6289 (Supersedes #6234) Lifting CapacitiesTelescopic Hydraulic Truck CraneHTC 865050 ton ( metric ton)Boom and fly Capacities for this machine are listed by the following sections:Fully Extended Outriggers Working Range Diagram (11,000 lbs. Counterweight) to ft. ( m) main boom Capacities , A max mode to 110 ft. ( m) main boom Capacities , Basic Mode B 34 ( m) ft. offset fly Capacities , Basic Mode B 34 to 56 ft. ( m) two piece offset fly Capacities , Basic mode B Link BeltHTC-8660 HTC-8650 CAUTION: This material is supplied for reference use only. Operator must refer toin cab Crane Rating Manual to determine allowable machine Lifting Capacities andoperating 2 -WARNINGREAD AND UNDERSTAND THE OPERATOR'S AND SAFETY MANUALS AND THEFOLLOWING INSTRUCTIONS AND RATED Lifting Capacities BEFORE OPERATING THECRANE.

2 OPERATION WHICH DOES NOT FOLLOW THESE INSTRUCTIONS MAY RESULT INAN INSTRUCTIONSGENERAL:1 . Rated Lifting Capacities in pounds as shown on lift charts pertainto this Crane as originally manufactured and normallyequipped. Modifications to the Crane or use of optionalequipment other than that specified can result in a reduction . Construction equipment can be dangerous if improperlyoperated or maintained. Operation and maintenance of thiscrane must be in compliance with the information in theOperator s, Parts, and Safety Manuals supplied with this these manuals are missing, order replacements through.

3 The operator and other personnel associated with this craneshall read and fully understand the latest applicable AmericanNational Standards ASME safety standards for . The rated Lifting Capacities are based on Crane standing levelon firm supporting UP:1 . The Crane shall be leveled on a firm supporting on the nature of the supporting surface, it may benecessary to have structural supports under the outriggerpontoons or tires to spread the load to a larger bearing . When making lifts on outriggers, all tires must be free ofsupporting surface. All outrigger beams must be extended tothe same length; fully retracted, intermediate extended, or fullyextended.

4 The front bumper outrigger must be . When operating on fully retracted outriggers, do not exceed70 maximum boom angle with 11,000 lb. counterweight. Lossof backward stability will occur causing a backward . When making lifts on tires, they must be inflated to therecommended pressure. (See Operation note 20 and TireInflation.)5 . Before swinging boom to over side position on tires, or on fullyretracted outriggers where Capacities are not published, boomsections must be fully retracted and 45 boom angle . For required parts of line, see Wire Rope Capacity and.

5 When installing or removing counterweights, Crane must be onfully extended outriggers and boom fully retracted. Do notexceed a 30 ft. radius when moving . Before setting up on intermediate outriggers, retractedoutriggers, or tires, refer to Working Range Diagrams and ratedlifting Capacities to determine allowable Crane :1 . Rated Lifting Capacities at rated radius shall not be not tip the Crane to determine allowable loads. For concretebucket operation, weight of bucket and load shall not exceed80% of rated Lifting Capacities . For clamshell bucket operation,weight of bucket and bucket contents is restricted to amaximum weight of 7,000 pounds or 80% of rated liftingcapacity, whichever is less.

6 For magnet operation, weight ofmagnet and load is restricted to a maximum weight of 7,000pounds or 80% of rated Lifting capacity, whichever is less. Forclamshell and magnet operation, maximum boom length isrestricted to 55 ft. and the boom angle is restricted to aminimum of 35 degrees. Lifts with either fly erected isprohibited for both clam and magnet . Rated Lifting Capacities shown on fully extended outriggers donot exceed 85% of the tipping loads. Rated Lifting capacitiesshown on intermediate extended or fully retracted outriggersare determined by the formula, rated load = (tipping load Xload factor) Rated Lifting Capacities shown on tires do notexceed 75% of the tipping loads.

7 Tipping loads are determinedby SAE Crane stability test code J . Rated Lifting Capacities in the shaded areas above the boldlines, are based on structural strength or hydraulic limitationsand have been tested to meet minimum requirements of SAEJ 1063 cantilevered boom Crane structures method of rated Lifting Capacities below the bold lines are based onstability ratings. Some Capacities are limited by a maximumobtainable 78 boom . Rated Lifting Capacities include the weight of the hook block,hook ball, slings, bucket, magnet, and auxiliary Lifting weights must be subtracted from the listed rated capacityto obtain the net load which can be lifted.

8 Rated liftingcapacities include the deduct for either fly stowed on the baseof the boom. For deducts of either fly erected, but not used, seeCapacity Deductions For Auxiliary Load Handling . Rated Lifting Capacities are based on freely suspended attempt shall be made to move a load horizontally on theground in any . Rated Lifting Capacities are for lift Crane service . Do not operate at radii or boom lengths (minimum or maximum)where Capacities are not listed. At these positions, the cranecan tip or cause boom . The maximum loads which can be telescoped are not definablebecause of variation in loadings and Crane maintenance, but itis permissible to attempt retraction and extension within thelimits of the applicable load rating.

9 For main boom Capacities when either boom length or radius orboth are between values listed, proceed as boom lengths not listed, use rating for next longerboom length or next shorter boom length, whichever load radii not listed, use rating for next larger 3 -HTC-865010 . The user shall operate at reduced ratings to allow for adversejob conditions, such as: soft or uneven ground, out of levelconditions, wind, side loads, pendulum action, jerking orsudden stopping of loads, hazardous conditions, experience ofpersonnel, traveling with loads, electrical wires, etc. Side loadon boom or fly is dangerous and shall be.

10 Rated Lifting Capacities do not account for wind on suspendedload or boom. Rated Capacities and boom length shall beappropriately reduced as wind velocity approaches or exceeds20 . When making lifts with auxiliary head machinery, the effectivelength of the boom increases by 2 . Power sections of boom must be extended in accordance withboom mode A or B . In boom mode B all power sectionsmust be extended or retracted . The least stable rated working area depends on theconfiguration of the Crane set . Rated Lifting Capacities are based on correct must be made for excessive reeving.