Long Life Cermet Potentiometer 2 Million Cycles

1 Sfernice Revision: 07-Mar-171 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Life Cermet Potentiometer 2 Million CyclesDESIGN SUPPORT TOOLSFEATURES 2 Million Cycles Cermet element mm square single turn panel control 4, 6 and shaft diameters and 29 terminal styles Multiple assemblies - up to four modules Test according to CECC 41000 or IEC 60393-1 Low temperature coefficient Custom designs on request Linearity 3 % ( 2 % available) Material categorization: for definitions of compliance please see logo to get startedAvailableModelsQUICK REFERENCE DATAM ultiple moduleUp to 4 modulesSwitch moduleYesDetent moduleYesSpecial electrical lawsA: linear, L: logarithmic, F.

2 Reverse logarithmic and others see specificationsSealing levelIP 64 Lifespan2M cyclesVERSATILEMODULARCOMPACTROBUSTCONFI GURATION EXAMPLE - Dimensions in millimeters (inches) mm ( ")Single module, single shaft, vertical mounting, PC pins with support plate, metric bushing and shaftDual modules, single shaft, PC pins with front support plates, imperial bushing and shaftM10 x ( ) ( )16( ) ( )8( ) ( ) ( )3/8" x 3/8" ( ) ( ) ( ) ( )8( ) ( ) ( ) ( ) ( ) ( ) Sfernice Revision: 07-Mar-172 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT SPECIFICATIONSNote Nothing stated herein shall be construed as a guarantee of quality or durabilityELECTRICAL (initial)Resistive elementCermetElectrical travel270 10 Standard resistance values1 k , 5 k , 10 k , 50 k Tolerancestandard 20 %on request 5 % or 10 %TaperCircuit diagramPower rating at 70 Clinear W at +70 Cnon-linear W at +70 Cmultiple W at +70 C per moduleTemperature coefficient (typical) 150 ppmLimiting element voltage350 VEnd resistance (typical)2 Independent linearity 3 % ( 2 % available)

3 Insulation resistance106 M strength1500 VRMS endurance2 000 000 cycles100806040200010080604020% CLOCKWISE SHAFT ROTATION% TOTAL RESISTANCE FLAa(1)b(2)c(3)cwAMBIENT TEMPERATURE IN CPOWER IN W0204060 70 80100 120 Sfernice Revision: 07-Mar-173 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT MECHANICAL (initial)Mechanical travel300 5 Operating torque (typical)Single and dual Ncm to Ncm max. ( to max.)Three to four modules (per module) Ncm to Ncm max. ( to max.)End stop torque4 mm dia. shafts35 Ncm max. ( lb-inch max.)6 mm and 1/4" dia. shafts80 Ncm max.

4 ( lb-inch max.)Tightening torque7 mm dia. bushings150 Ncm max. (13 lb-inch max.)10 mm and 3/8" dia. bushings250 Ncm max. (21 lb-inch max.)Weight7 g to 9 g per module ( oz. to oz.)ENVIRONMENTALO perating temperature range-55 C to +125 CClimatic category55/125/56 SealingIP64 MARKING Potentiometer module vishay logo, SAP code of ohmic value, and tolerance in %, identify P11L version, variation law, manufacturing date (four digits), 3 for the lead 3 Switch module Version, manufacturing date (four digits), c for common leadPACKAGING BoxPERFORMANCESTESTSCONDITIONSTYPICAL VALUES AND DRIFTS RT/RT (%) R1-2/R1-2 (%)OTHERE lectrical endurance1000 h at rated power90 /30 - ambient temp. 70 C 2 %--Climatic sequenceDry heat at +125 C/damp heatcold -55 C/damp heat, 5 Cycles 1 %--Damp heat, steady state+40 C, 93 % relative humidity56 days 2 %-Insulation resistance: > 1000 M Change of temperature-55 C to +125 C, 5 Cycles %--Mechanical endurance2 Million cyclesturn angle: 60 temperature: 20 C 20 %-Independent linearity: 10 %Shock50 g s, 11 ms3 shocks - 3 directions % %-Vibration10 Hz to 55 mm or 10 g s, 6 h %- V1-2/V1-3 = % Sfernice Revision: 07-Mar-174 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

5 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ORDERING INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFT STYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALP11L1234 STANDARD RESISTANCE ELEMENT DATASTANDARDRESISTANCE VALUESLINEAR TAPERNON-LINEAR TAPERMAX. POWERAT 70 CMAX. WORKINGVOLTAGEMAX. POWERAT 70 CMAX. WORKINGVOLTAGE Sfernice Revision: 07-Mar-175 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Hardware supplied in separate bags ORDERING INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFT STYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIAL LF3/8"3/8"Q7 DIMENSIONSABCKJPANEL CUT OUT HGBushings F and VG HBushingQBUSHINGSmm ( )mm ( )INCHES ( )VQFAS hafts 641/4 BBushing 1073 versions thread/inchWrench Sfernice Revision: 07-Mar-176 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

6 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ORDERING INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFT STYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALA =see table belowB =C =0 =withoutpegLOCATING PEGS (anti-rotation lug)The locating peg is provided by a plate mounted on the bushing and positioned by the module sides. Four set positions are available, clock face orientation: 12, 3, 6, d (mm)L (mm)e (mm)All P11 bushings have a double flat. When panel mounting holes have been punched accordingly, an anti-rotation lug is not peg code C not available for bushing pegs are supplied in separate bags with nuts and washers 12L369 Sfernice Revision: 07-Mar-177 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

7 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ORDERING INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATING PEGSHAFTSHAFTSTYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIAL LS = slottedAP = Custom shaftR = = = customEJ422FG616FL625FR650GG1/4"5/8"GH1/ 4"3/4"GJ1/4"7/8"GL1/4"1"GO1/4" "SHAFTS - Dimensions in millimeters (inches)The shaft length is always measured from the mounting shafts are designed by a 3 letters code (3 digits). Shaft slots and flats are aligned with the wiper position ( 10 ); picture shows shaft with wiper at middle of mechanical/electrical standard shafts are slotted except flatted and splined, see exeptions for SHAFTFLATTED SHAFTCUSTOM SHAFTSWhen special shafts are required - flat, threated ends, special shaft lengths, etc.

8 A drawing is COMBINATION OF SHAFT STYLES AND BUSHINGSSHAFT CODESHAFT LENGTH AND STYLE AVAILABLE IN STANDARD(others on request) 7 619 Bushing: QShaft: : FShaft: Sfernice Revision: 07-Mar-178 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATING PEGSHAFTSHAFTSTYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALA vailable leadsA00 W00 X00 Y00 Z00A10 W10 X03 Y03 Z03A13 W20 X04 Y04 Z04A14X10Z10A20X13Z13A23X14Z14A24X20Z20X 23Z23X24Z24 FIRST DIGITSECOND DIGITTHIRD DIGITYS oldering lugs0Y = ( ") A, X, Z, W = ( ") pin spacing pins section x ( " x ") ( ") space between modulesXPCB ( ") space between modulesZPCB pins with front support ( ") space between modulesAPCB pins with front and back support ( ") pin spacing pin section x ( " x ")

9 WPCB pins - vertical mounting with 2 extra pins - 1 module ( ") pin spacing pins section x ( " x ")DIMENSIONS in millimeters (inches) mm ( ")THE POSITION OF EACH MODULE IS FREEBUSHINGSMILLIMETERS ( )INCHES ( )VQFEL eads Z1. Z2. Z0: ( ")Leads , Z2: ( ")JLeads ( ) ( )J13( ) ( ) ( ) ( ) ( ) ( ) ( )5( ) ( ) ( )SOLDER LUGS ( ) ( )X12X-X23123 PCB PIN OUTHORIZONTAL ( )321A/A2( ) ( )A1 AND REAR SUPPORT PLATESFRONT SUPPORT PLATE ( ) ( ) ( ) ( ) ( ) ( )2Z1ZZ123123123 VERTICAL MOUNTINGABCK4( ) ( ) ( ) ( ) ( ) ( )W-W21 2 3W112 3 Rear Sfernice Revision: 07-Mar-179 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (part number)P11L2 FAGOSY00502 KAMODELNUMBER OFMODULESBUSHINGLOCATING PEGSHAFTSHAFTSTYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALR esistance code:1K = 102 5K = 502 10K = 103 50K = 503 Tolerance code:standard: M = 20 %on request: K = 10 %, J = 5 %Taper: A, L, Forspecial code given by VishaySPECIAL CODES GIVEN BY VISHAYO ption available.

10 Custom shaft Specific design on request Specific linearity Multiple assemblies with various modulesAPPLICATION NOTE The Potentiometer shall be used in voltage divider with an impedance load at least 100 times higher than the total Potentiometer nominal resistance load impedance: 1 M min. for resistance range of 1 k to 50 k (1) a(2) bc (3)cwVsVeZ >1 M Sfernice Revision: 07-Mar-1710 Document Number: 51060 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT OPTION: ROTARY SWITCH MODULES Rotary switch Current up to 2 A Actuation CW or CCW position Sealing IP60 MODULES: RS ON/OFF SWITCH RSI CHANGEOVER SWITCHThe position of each module is and RSI rotary switches are housed in a standard P11L module size mm x mm x mm ( " x " x ").