Marchand Electronics Inc.

1 Marchand Electronics ManualXM26 Tube electronic CrossoverXM26 Tube electronic of CabinetGeneralThe XM26 cabinet contains 2 XM26 tube crossovernetworks and a PS227 power supply. Additionally thecabinet has 4 level controls, power switch, sum switchand 3 indicator lights on the front panel. The rearpanel has the 6 RCA signal connectors, line cord XM26-KK kit contains the following parts:Parts List1 Cabinet front panel XM261 Cabinet adapter panel1 Cabinet Rear Panel1 Cabinet Shell1 Cabinet Top4 Rubber feet + scews486 x Button head cap screw1PS227 Power supply Kit2XM26 Xover board Kit4XM26-FMFrequency Modules1 Line Cord1T1 Toroidal Power Transformer with mounting hardware1 Hex wrench 1/16 1 Hex wrench 5/64 A bag with the following parts.

2 3 RCA connector RED3 RCA connector BLACK1 Fuse Holder1 Fuse, 1A 250V1 Power entry connector1 Voltage selector switch171/2"Threaded Standoff5#6 x button head cap screw5#6 x machine screw176/32 * 3/8 Machine Screw216/32 * Machine Screw Black1#6 Solder Lug2 Nylon cable Machine Screw4#4 Locknut4AT12 Level Control Attenuator 50K3 Red or Amber LED3 Holder for LED2 DPDTR ocker Switch Black4 Black Aluminum Knob2'1/8"Heat Shrink Tubing2'Black#22 hookup wire8'Brown#22 hookup wire8'Red#22 hookup wire8'Orange#22 hookup wire2'Green#22 hookup wire2'Blue#22 hookup wireAssembly

3 InstructionsThe front panel, rear panel and shell will beassembled separately and joined together at the assemble the PS227-K power supply and the twoXM26-K crossover boards according to theinstructions provided. Assembly of Rear Panel The rear panel holds the RCA connectors and thepower cord and the fuse the 6 RCA connectors in the holes input, highpass, low pass. The left channel has the connectorswith the BLACK insulators. The right channel gets theRED insulators. Each connector has two insulators,one with a shoulder and the other is flat.

4 Make surethe shoulder is inserted in the hole of the panel. Installthe flat insulator on the other side of the panel. Installthe solder lug and the nut. Tighten the nut the fuse holder in the panel. The white washeris installed on the outward side. Gently tighten the much force will crack the the Power entry connector using two 4/40 x3/8 screws and #4 the voltage selector switch using two 4/40 x3/8 screws and #4 locknuts. Orient the selectorswitch so that when the selector is switched towardsthe fuse holder it shows wires to the RCA connectors.

5 Prepare 4 pairsof wire by taking an 18" length of red and brown wireand twisting together. Slip a 3/4" length of heat shrinktubing over the end of each wire at one side of thepair. Strip 1/4" of insulation off each wire. Solder thebrown wire onto the solder lug of the the red wire into the center pin of theconnector. Slip the heat shrink tubing over the solderjoints. Shrink the tubing with a heat gun. If no heat gunis available use the heat of a soldering iron. Repeat this for all RCA assembly of the rear panel is now complete.

6 Put itaside until of Front PanelInstall the 4 50K attenuators in the positions labeledlevel. Tighten the nuts carefully. One DPDT switchmounts in the position marked power and the otherDPDT switch mounts in the position marked are 3 holes left for the indicator LEDs. Do notinstall these LEDs yet at this wires to attenuators. Prepare 3 10" lengths ofred, orange and brown wire. Strip 1/4" of insulationfrom each end. Solder one end of each wire to anattenuator. T=brown, W=red, B=orange. Twist the wires to form a 3-wire cable.

7 Repeat above step for all four two blue 9" wires to the sum mode wire goes to the bottom terminal of the switchand the other goes to the center terminal. The topterminal remains unused. Cover the solder joints witha 1/2" length of heat shrink tubing and shrink with heatgun. Assembly of ShellPlace the shell on a flat surface with the bottom front of the shell is labeled as such. Place thefront of the shell towards you. The 2 XM26 crossoverboards will be mounted in the holes marked at theright hand side of the chassis.

8 Each board uses 6 1/2"standoffs and 12 # 6-32x1/4" screws. Install thestandoffs in the holes using flathead 6-32 mount the XM26 crossover boards on the PS227 at the holes marked, using four 1/2"standoffs. The side with the terminal blocks faces thetransformer. Use star locking washers under thescrews in the bottom shell. This is important. Thestarwashers will insure that the power supply isproperly the TO5 voltage regulator on the rear panel ofthe cabinet.

9 Use a mica insulator between theregulator rear panel. The mica insulator should becoated with heat sink compound on both the toroidal transformer to the left of the PS227board with the mounting hardware included with thetransformer. The wiring of the transformer to the PS227 board isshown in the manual that comes with the power wiring between the PS227 power supplyboard and the two XM26 crossover boards is shownin table 1. Prepare wire lengths of the proper lengthand color, strip 1/4" of insulation from each end, insertinto the terminal block and fasten the screw.

10 Thepower wires typically run from the PS227 to the leftXM26 with one wire and then from the left XM26 tothe right XM26 with another wire. Twisting the wirestogether will make for a nice it all togetherThe Signal Wiring for the rear panel connectors isshown in table 2. A good way to do this is to place therear panel right next to the rear of the shell, but do notscrew it on. This way it is easier to insert the wires intothe terminal blocks. Note that the input signals arehooked up to both IN1 and IN2 of the XM26 crossovernetworks.