MATERIAL SAFETY DATA SHEET - Chammas Cutters

1 SUPPLIER: Chammas Cutters , or Component:Black PowderN/ANEC opper 1 mg / m 3 ZincNEBOILING POINT: N/ASPECIFIC GRAVITY (H2O = 1) - POINT:N/AN/A VAPOR DENSITY (AIR=1): N/AEVAPORATION RATE (Butyl Acetate=1):N/ASOLUBILITY/WATER: HighAPPEARANCE AND ODOR: Black - No OdorFLASH POINT: N/AAUTO IGNITION: > 464 F LEL: N/A UEL: N/ANFPA HAZARD CLASSIFICATION: Flammable 1 HEALTH: 0 REACTIVITY: 0 SPECIAL: N/AFIRE FIGHTING: Do not fight fires. Evacuate FIRE/EXPLOSION HAZARDS:Powder may deflagrate or explode in a fire due to heat and/or confinement. Detonation produces hazardous fragments. Gases produced may contain iron, lead, carbon and nitrogen NO PEL/OSHA TLV/ACGHI NE 1 mg / m 3 NEVAPOR PRESSURE (mm hg):EMERGENCY NUMBER: 1-800-255-3924 FIRE and EXPLOSION DATAPHYSICAL / CHEMICAL CHARACTERISTICS and DATAPRODUCT - IGNITERMATERIAL SAFETY data SHEETUN0454 PGII EX#2010040812 INGREDIENT HAZARD STATEMENT: BLACK POWDERC hammas Cutters Inc Part Numbers:# 068017 - 11/16-1 1/4 IGNITER (Small BP4) UN0454 11320 FM 529, Bldg.

2 IHouston, Texas 77041 Tel: 713-856-8777#137017 - 1 3/8-7 1/2 IGNITER (Regular BP4) UN0454 #137027 - 1 3/8-7 1/2 IGNITER (Long BP4) UN0454 PRODUCT INFORMATION:BRASS SHELLS CONTAINING BLACK POWDER07440-50-807440-66-6 PRODUCT IDENTIFICATION:Trade Name: Igniter, UN0454, Class , Packing Group II, EX#2010040812 Chammas Cutters , 1 MSDS 03/2011 CARCINOGENICITY NTP: N/AIARC: N/AOSHA: N/ASPILLS/RELEASE: Packets may be picked up carefully and returned to : Avoid rough handling and dropping, may detonate with impact or on SMOKING, store in a cool, dry not open containers in bulk storage PROTECTION: SAFETY Glasses or gogglesCLOTHING: Use static free clothing, cotton overalls, undergarments, and socks. Conductive soled shoes, impervious rubber PRECAUTIONS: Keep away from friction, impact, and heat. NO SMOKING. Wash hands after handling. Do not consume food or drink in areas where they may become contaminated with these HAZARD: XSUDDEN PRESSURE RELEASE:REACTIVITY :ACUTE (IMMEDIATE) HEALTH HAZARD: DELAYED (CHRONIC) HAZARD:CONVERSION VALUE TO POUNDS: 50.

3 CHEMICAL DESCRIPTOR: CLASS C EXPLOSIVES tore in accordance with the requirements of Subpart K, ATF: Explosives Law and Regulations (27 CFR ).supervisor or the manufacturer before you have any questions or doubts as to how to use any explosive product, DO NOT USE IT. Consult with yourexperienced persons in accordance with all applicable federal, state, and local laws, regulations, or handled and used following approved SAFETY procedures either by or under the direction of competent,Emergency Response Guidebook, Guide 114 for further details. All explosives are dangerous and must beGuard against intruders. Division Explosives - Evacuate the area for 1500 feet (1/3 mile). Consult the 2000 VENTILATION: Use only with adequate ventilationRESPIRATORY PROTECTION: NIOSH approved particle masks for dust and do not present health hazards in normal handling and use; however, the products are Division explosives anddetonation may cause severe physical injury, including death.

4 All explosives are dangerous and must be handledcarefully and used following approved SAFETY procedures under the direction of competent, experienced persons in SARA HAZARD CATEGORIESCONTROL MEASURES accordance with all applicable federal, state, and local laws, regulations, and of explosives powders may cause nervous system irregularities including headaches and oxides generated during the use are skin, eye, and respiratory tract HANDLING & USE DATAHEALTH DATAREACTIVITY DATASTABILITY: Product is stable, HANDLE CAREFULLY and keep away from flame or excessive / BY-PRODUCTS: Polymerization will not occurINSTABILITY: Acids and alkalisDO NOT FIGHT EXPLOSIVES FIRES. Try to keep fire from reaching explosives. Isolate Cutters , 2 MSDS 03/2011