Material Safety Data Sheet(MSDS) - vnsourcing.com.vn

1 Material Safety data sheet ( msds ). 1. Chemical & Company Identification Trade Name multifak EP 2 Product Code L4123. Name GS Caltex Corporation Address GS Tower, Yoksam-dong, Kangnam-gu, Seoul, 135-985, Korea Supplier Routine Inquiries 82-2-2005-6841~8. Fax 82-2-565-5156. Chemical Description Grease 2. Hazards Identification HANDLE Material IN PRESSURE EQUIPMENT WITH CARE. ACCIDENTAL INJECTION. Warning Statements CAN CAUSE SERIOUS TISSUE DAMAGE. Eyes Not expected to cause prolonged or significant eye irritation. Oral Not expected to be harmful if swallowed. Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of Inhalation oil mist at airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include coughing and difficulty breathing.

2 Contact with the skin is not expected to cause prolonged or significant irritation. Not expected to be harmful to internal organs if absorbed through the skin. High-Pressure Equipment Information: Accidental high-velocity injection under the skin of materials of this type may result Skin in serious injury. Seek medical attention at once should an accident like this occur. The initial wound at the injection site may not appear to be serious at first; but, if left untreated, could result in disfigurement or amputation of the affected part. Long term None. toxic effect 3. Composition & Ingredients Components CAS No. Range in %. Severely Hydrotreated Heavy Paraffinic Distillate 80 - 85. Additives which may include detergent-inhibitor, viscosity Not Available 15 - 20. index improver, pour point depressant, or antifoam agent 4. First Aid Measures No specific first aid measures are required.

3 As a precaution, remove contact lenses, if worn, Eyes and flush eyes with water. No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the Material from skin, apply a waterless hand cleaner, mineral oil, Skin or petroleum jelly. Then wash with soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse. Energy Leader, GS Caltex 1/4. No specific first aid measures are required. If exposed to excessive levels of Material in the air, Inhalation move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs. No specific first aid measures are required. Do not induce vomiting. As a precaution, Ingestion get medical advice. In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident may result in a small, sometimes bloodless, puncture wound.

4 However, Advice to doctor because of its driving force, Material injected into a fingertip can be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing pain. Immediate treatment at a surgical emergency center is recommended. 5. Fire Fighting Measures Ignition temp. (Degrees C) Not Determined Flammable limits (% by volume) Not Determined Flash point (Degrees C) Not Determined According to the National Fire Protection Association Guide, use water fog, dry chemical, foam, or carbon dioxide. Water or foam may cause frothing. Use Fire extinguishing agents water to cool fire-exposed containers. If a leak or spill has not ignited, use water spray to disperse the vapours and to provide protection for persons attempting to stop the leak. For fires involving this Material , do not enter any enclosed or confined space Explosion hazards without self-contained breathing apparatus to protect against the hazardous effects of combustion products or oxygen deficiency.

5 6. Accidental Release Measures Stop the source of the leak or release and contain spill if possible. Ventilate area. Use respirator and protective clothing as discussed in this msds . Cover spill with a generous amount of inert absorbent. Use a stiff broom to mix thoroughly. Sweep up and place in a disposable container. In case of spill Scrub contaminated area with detergent and water using a stiff broom. Pick up liquid with additional absorbent and place in a disposable container. Prevent contamination of groundwater or surface water. 7. Handling & Storage Minimum feasible handling temperatures should be maintained. Periods of exposure to high temperatures should be minimised. Water contamination should be avoided. General Misuse of empty containers can be hazardous. DO NOT cut, weld, heat or drill container. Residue may ignite with explosive violence if heated sufficiently. Do not pressurize or expose to open flame or heat.

6 Keep container closed and drum bungs in place. 8. Exposure Control/Personal Protection No special eye protection is normally required. Where splashing is possible, wear Safety Eyes glasses with side shields as a good Safety practice. No special protective clothing is normally required. Where splashing is possible, select protective clothing depending on operations conducted, physical requirements and other Skin Energy Leader, GS Caltex 2/4. substances in the workplace. Suggested materials for protective gloves include: Neoprene, Nitrile Rubber, Silver Shield, Viton. No special protective clothing is normally required. Where splashing is possible, select protective clothing depending on operations conducted, physical requirements and other Skin substances in the workplace. Suggested materials for protective gloves include: Neoprene, Nitrile Rubber, Silver Shield, Viton. No respiratory protection is normally required.

7 If user operations generate an oil mist, determine if airborne concentrations are below the occupational exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection from the measured Inhalation concentrations of this Material . For air-purifying respirators use a particulate cartridge. Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not provide adequate protection. Use adequate ventilation to keep the airborne concentrations of this Material below the Ventilation ACGIH TLV for mineral oil mists. Local exhaust ventilation and/or enclosure of the process is preferred in these cases. The ACGIH TLV for mineral oil mists is 5 mg/m 3 for a daily 8-hour exposure. Exposure limits A short term exposure limit (STEL) of 10 mg/m 3 is recommended. 9. Physical & Chemical Properties Appearance Heavy Brown Odor - pH Not Applicable Solubility(water) Negligible Boiling point(deg.)

8 C) Not Determined Evaporation Not Determined Vapor pr.(mmHg) Not Determined Density Not Determined Vapor density(air=1) Not Determined Viscosity Not Determined 10. Stability & Reactivity Hazardous Polymerizations DO NOT OCCUR. Carbon monoxide, carbon dioxide, and aldehydes and ketones, combustion products Products of combustion of nitrogen or sulfur. Conditions to avoid Strong oxidizers such as chlorates, nitrates, peroxides, etc. 11. Toxicological Information This product contains petroleum base oils which may be refined by various processes including severe solvent extraction, hydrocracking and hydrotreating. These oils have not been listed General in the National Toxicology Program (NTP) Annual Report nor have they been classified by the International Agency for Research on Cancer (IARC) as carcinogenic or probably carcinogenic to humans. 12. Ecological Information Environmental effects This Material is not expected to be harmful to aquatic organisms.

9 13. Disposal Considerations Place contaminated materials in disposable containers and dispose of in a manner consistent Waste disposal with applicable regulations. Contact local environmental or health authorities for approved disposal of this Material . Energy Leader, GS Caltex 3/4. Place contaminated materials in disposable containers and dispose of in a manner consistent Waste disposal with applicable regulations. Contact local environmental or health authorities for approved disposal of this Material . This Material may present environmental risks common to oil spills. Contact your local oil spill Remarks response group and applicable government agencies if a spill occurs. 14. Transport Information UN Number Not Applicable Dangerous Goods Class Not Applicable Proper Shipping Name Not Applicable Hazchem Code(Australia/NZ) Not Applicable Additional Information None Determined 15.

10 Regulatory Information In the absence of local approved authorities, follow NIOSH/MSHA, BSI, Respirator Information or joint Australia-New Zealand AS/NZS 1715/1716. Respirators must follow AS/NZS. 1715/1716 standard for approved respirators. 16. Other Information To the best of our knowledge, the information provided in this msds document is correct. Access to this information is being provided via the Internet so that it can be made available to as many potential users as possible. We do not assume any liability for consequences of the use of this information since it may be applied under conditions beyond our control or knowledge. Also, it is possible that additional data could be made available after this msds was issued. Certain hazards are described herein, however these may not be the only hazards that exist. All materials may present unknown hazards and should be used with caution.