MATERIAL SAFETY DATA SHEET - Technology …

1 10 Page 1 of 7 MSDS No.: 0106 MATERIAL SAFETY data SHEET CUTTING OIL Revision Date: 08/09/2003 Technology Supplies Ltd, Phoenix House, Tern Hill, Market Drayton, Shropshire. TF9 3PX. Tel: 01630 637300 Fax: 01630 637302 PRODUCTS IDENTIFICATION: Cutting Oil USE OF SUBSTANCE: Water mix cutting fluid COMPANY: Morris Lubricants Castle Foregate Shrewsbury Shropshire SY1 2EL Telephone Number: 01743 232200 Fax No: 01743 353584 EMERGENCY TELEPHONE: 01743 232200 This product is classified as hazardous under current UK Health/ SAFETY /Environmental Legislation but should be handled in accordance with good industrial hygiene and SAFETY practices. Adverse Health Effects: Repeated contact with the skin may result in skin irritation.

2 Other Hazards: The product can burn when strongly heated. Hazardous decomposition products may be formed. Hazardous Components in Product: Name CAS No % Mass Symbols/OEL R Phrases Diethylene glycol 111-46-6 1-5 Xi R22 Butylene diglycol 112-34-5 1-5 Xi R36/38 Fatty Alcohol Ethoxylate 68920-66-1 1-5 Xi R36/38 Severely refined mineral oil (IP 346 DMSO extract <3%) 60-90 OEL 1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND THE COMPANY / UNDERTAKING 2. HAZARDS IDENTIFICATION 3. COMPOSITION/INFORMATION ON INGREDIENTS 10 Page 2 of 7 MSDS No.: 0106 MATERIAL SAFETY data SHEET CUTTING OIL Revision Date: 08/09/2003 Technology Supplies Ltd, Phoenix House, Tern Hill, Market Drayton, Shropshire. TF9 3PX. Tel: 01630 637300 Fax: 01630 637302 Inhalation: If inhalation of mist, fumes or vapour causes irritation to the nose or throat remove to fresh air.

3 If symptoms persist obtain medical advice. Skin Contact: Wash skin thoroughly using soap and water and seek medical advice if symptoms persist. Eye Contact: Rinse with plenty of water (also under eyelids) for at least 10 minutes and seek medical attention if symptoms persist. Ingestion: Seek medical attention. DO NOT INDUCE VOMITING Extinguishing Media: Use carbon dioxide, foam or water spray. Prevent water used in spray from entering watercourses. Not to be Used: Direct water jet. (use water only to keep fire exposed containers cool). Special Fire-Fighting Procedures: In the event of a large fire self-contained breathing apparatus should be worn. WARNING: Heat from fire could possibly result in drums bursting.

4 Contain and collect spillage with help of absorbent materials such as floor granules. Protect drains from potential spills to minimise contamination. If spillage enters drains call Environment Agency Emergency hotline on 0800 807060. Product waste should be disposed of according to Item 13. Handling: Precautions should be taken against skin and eye contact. Avoid inhalation of vapour mist or fume. Do not wear contaminated clothing. Wear SAFETY shoes when handling containers. Storage: 4. FIRST-AID MEASURES 5. FIRE-FIGHTING MEASURES 6. ACCIDENTAL RELEASE MEASURES 7. HANDLING AND STORAGE 10 Page 3 of 7 MSDS No.: 0106 MATERIAL SAFETY data SHEET CUTTING OIL Revision Date: 08/09/2003 Technology Supplies Ltd, Phoenix House, Tern Hill, Market Drayton, Shropshire.

5 TF9 3PX. Tel: 01630 637300 Fax: 01630 637302 Store away from sources of strong heat and strong oxidising chemicals. Keep containers tightly closed in a cool dry, well ventilated place. Take precautionary measures to prevent spills into drains, soil or water. External tanks or stillage should be bunded. Engineering Measures: Ensure good ventilation. Use protective equipment and/or local ventilation when needed. Avoid skin contact and inhalation of oil mist. Exposure Values: Comply with current local occupation exposure limit. It is recommended that mineral oil mists are kept below 5mg/m3 (8hr TWA value) EH40. Protection and Hygiene: Wash hands before breaks and immediately after handling the product. Thoroughly clean contaminated skin and change dirty clothing and equipment .

6 Respiratory Protection: Oil Mist: respirator (combined particle and organic vapour filter type A2/P2) Hand Protection: Wear gloves (PVC, Nitrile rubber). For further information consult glove manufacturer for recommendations of glove type associated with your particular application, so that break-through times can be assessed. Show this data SHEET . Eye Protection: SAFETY goggles if there is a risk of splashing Skin Protection: protective clothing when needed. Appearance at 20 C: Clear liquid Odour: Phenolic pH: Density at 15 C: Viscosity at 40 C cSt: 36 Flash Point (ASTM D93): Greater than 170 C Auto-ignition Temperature (ASTM E659): Greater than 250 C Explosion Limits: Not established Vapour Pressure 20 C < kPa Solubility: Miscible with water to form an emulsion Physical Characteristics: Appearance (Emulsion): Rich Milky White SG at 15 C: pH @ 20 C (5% Emulsion): Corrosion Breakpoint IP 287: 25:1 (4%) 8.

7 EXPOSURE CONTROLS/ personal PROTECTION 9. PHYSICAL AND CHEMICAL PROPERTIES 10 Page 4 of 7 MSDS No.: 0106 MATERIAL SAFETY data SHEET CUTTING OIL Revision Date: 08/09/2003 Technology Supplies Ltd, Phoenix House, Tern Hill, Market Drayton, Shropshire. TF9 3PX. Tel: 01630 637300 Fax: 01630 637302 Corrosion Test IP 125: 35:1 ( ) Stability: Stable under normal conditions of use Thermal Decomposition: Slow decompositions above 200 C. Hazardous Reactions: Incomplete combustion will generate smoke, carbon dioxide, hazardous gases including carbon monoxide. Eyes: Unlikely to cause more than transient stinging or redness if accidental eye contact occurs Skin: Unlikely to cause harm to the skin on brief or occasional contact but prolonged or repeated exposure may lead dermatitis.

8 Ingestion: Unlikely to cause harm if swallowed in small doses. Larger doses may cause nausea and diarrhoea. Inhalation: At normal ambient temperatures is unlikely to cause inhalation hazard because of low volatility. Acute Toxicity: The refines mineral base oils used in this formulation are of low order of toxicity. LD50 (RAT) for base oil greater than 5g/kg Water: The individual components range from readily to poorly biodegradable. The components are not expected to be highly toxic to aquatic life. If released to water, the product may deplete the oxygen supply to bottom dwelling organisms. Soil: Small quantities will be absorbed in the upper layers where biodegradation should take place. Larger quantities may penetrate the anaerobic soil layers in which some of the organic compounds may persist.

9 Some compounds have a high soil absorption coefficient; some will be capable of penetrating the soil to cause ground water contamination. 10. STABILITY AND REACTIVITY 11. TOXICOLOGICAL INFORMATION 12. ECOLOGICAL INFORMATION 10 Page 5 of 7 MSDS No.: 0106 MATERIAL SAFETY data SHEET CUTTING OIL Revision Date: 08/09/2003 Technology Supplies Ltd, Phoenix House, Tern Hill, Market Drayton, Shropshire. TF9 3PX. Tel: 01630 637300 Fax: 01630 637302 Waste: Send to a registered waste disposal site using the sources of a Registered Waste Disposal Contractor. Ensure conformation with Local and National Regulations. Packaging: Labels should not be removed from containers until they have been cleaned. Empty containers may contain hazardous residues.

10 Ensure conformance with Local and National Regulations. Specific Advice: As supplied MATERIAL should be considered as Special Waste and Disposal should conform with the relevant Regulations. General: Under no circumstances should this product be disposed of by putting into drains, soil or water courses. UN No: N/A Packaging Group: N/A Shipping Name: N/A Marine Pollutant: No IMO Class: N/A ICAO/IATA: N/A ADR/RID: N/A This product is not classified as hazardous for supply in the UK SAFETY Phrases: S24/25 Avoid contact with the skin and eyes Statutory Instruments: The Health & SAFETY at Work Act 1974 Consumer Protection Act Environmental Protection Act COSHH Regulations CHIP Regulations Guidance: COSHH Essentials CHIP for everyone 13.